Where do I put the catflap?
Author
Discussion

james_tigerwoods

Original Poster:

16,347 posts

228 months

Tuesday 25th October 2011
quotequote all
Idiot question....

I need to fit a catflap - well, not so much "need" as "have" - however, I'm not 100% where, structurally, would be the best place to put it:



It's a 4.5cm thick wooden (exterior) door and I don't want to fit it where it would weaken the door.

I did suggest just making the cat live in the shed, but this was frowned upon...

Thanks

JTW

mgtony

4,226 posts

221 months

Tuesday 25th October 2011
quotequote all
Your only option is really only at the bottom of one of the raised panels. If there is a step down on the outside of the door, that position could make it too high for the cat, unless you can teach it to do a running jump at it.
Once cut, the bottom of the panel (the top of the cat flap) might want a bit of reinforcing.

Why are cat flaps so horrid to look at? smile

S1_RS

782 posts

230 months

Tuesday 25th October 2011
quotequote all
In the righthand panel, the std size flap should fit in without cutting into any of the main door frame. If you put it in the left hand panel it will hit the wall to the left when you open the door.

Stevenj214

4,941 posts

259 months

Tuesday 25th October 2011
quotequote all
james_tigerwoods said:
Idiot question....

I need to fit a catflap - well, not so much "need" as "have" - however, I'm not 100% where, structurally, would be the best place to put it:

It's a 4.5cm thick wooden (exterior) door and I don't want to fit it where it would weaken the door.

I did suggest just making the cat live in the shed, but this was frowned upon...

Thanks

JTW


HTH.

Please note: Despite the accuracy of these drawings they are no substitute for a full engineers report and calculations.

Shaw Tarse

31,904 posts

234 months

Tuesday 25th October 2011
quotequote all
Stevenj214 said:


HTH.

Please note: Despite the accuracy of these drawings they are no substitute for a full engineers report and calculations.
rofl

Munter

31,331 posts

272 months

Tuesday 25th October 2011
quotequote all
Doesn't matter where you put it. The cat will refuse to use it to come in. Oh sure it'll go out. But then it'll sit outside and complain that the usual window is not open to allow access to the house. Pesky things.

james_tigerwoods

Original Poster:

16,347 posts

228 months

Tuesday 25th October 2011
quotequote all
Catflap in the wall? Been there, done that:



And the cat would probably ignore it, but I'm more than happy to not cave in to it's unreasonable demands. Funnily enough there seems to be a catflap in the garage door - I'm also not allowed to insist the cat lives in there.

Thanks for responses though smile

eltawater

3,554 posts

210 months

Tuesday 25th October 2011
quotequote all

E36GUY

5,907 posts

249 months

Tuesday 25th October 2011
quotequote all
mgtony said:
...that position could make it too high for the cat...
rofl No such thing.

Simpo Two

93,115 posts

296 months

Tuesday 25th October 2011
quotequote all
E36GUY said:
mgtony said:
...that position could make it too high for the cat...
rofl No such thing.
My catflap has a little step underneath on the outside so ickle furbag doesn't hurt her tummy in transit paperbag

anonymous said:
[redacted]
I had a new kitchen door made recently and the factory (local d/g place) was quite happy to pre-fit one, either from their stock or fit one I supplied.

But which part of cutting a hole is difficult?

james_tigerwoods

Original Poster:

16,347 posts

228 months

Tuesday 25th October 2011
quotequote all
The ridiculous thing is that my cat hasn't moved from her perch all day - She never goes out anyway.

She'd go out for a few minutes, come back in to either st in the litter tray or on the floor, then go back on to her perch again.

This is where she spends all her time:



Yes, that is a lamp on a timer for the cat. No, I didn't put it there by my own choice.

XJSJohn

16,152 posts

250 months

Tuesday 25th October 2011
quotequote all
james_tigerwoods said:
Yes, that is a lamp on a timer for the cat. No, I didn't put it there by my own choice.
rofl

Simpo Two

93,115 posts

296 months

Tuesday 25th October 2011
quotequote all
anonymous said:
[redacted]
They do - well mine did. It was a uPVC kitchen door with solid lower panel. The panel is only two sheets of plastic with foam in the middle. Very easy to cut. So go and find yourself a nice local outfit that makes stuff on site and sells direct, not some multinational sleazeball on commission-only.

del 203

12,728 posts

280 months

Tuesday 25th October 2011
quotequote all
anonymous said:
[redacted]
:snigger:


AdeTuono

7,626 posts

258 months

Tuesday 25th October 2011
quotequote all
james_tigerwoods said:
The ridiculous thing is that my cat hasn't moved from her perch all day - She never goes out anyway.

She'd go out for a few minutes, come back in to either st in the litter tray or on the floor, then go back on to her perch again.

This is where she spends all her time:



Yes, that is a lamp on a timer for the cat. No, I didn't put it there by my own choice.
What did you use to cut the worktop? A chainsaw? yikes

mart77

250 posts

211 months

Tuesday 25th October 2011
quotequote all
i hate cats.evil bird killing little sts that just want feeding.sell the cat,but a dog and keep your door in one piece.simples

jimmyjimjim

8,348 posts

269 months

Tuesday 25th October 2011
quotequote all
mart77 said:
i hate cats.evil bird killing little sts that just want feeding.sell the cat,but a dog and keep your door in one piece.simples
Until the fecker wants to get out and claws his way through it!

SWH

1,261 posts

233 months

Tuesday 25th October 2011
quotequote all
The installation can go slightly awry when a daft hound becomes involved....


Yes, an internal door; keeps sleeping cats/dog apart.

Tim330

1,346 posts

243 months

Tuesday 25th October 2011
quotequote all
Teach the cat this

http://www.youtube.com/watch?v=wsTpC7CKMa4&fea...

I don't think any cat would be dexterous enough to deal with a locked door though

Nickyboy

6,826 posts

265 months

Tuesday 25th October 2011
quotequote all
Stevenj214 said:


HTH.

Please note: Despite the accuracy of these drawings they are no substitute for a full engineers report and calculations.
roflroflroflroflrofl