Drilling a new number plate?
Drilling a new number plate?
Author
Discussion

Tyy

Original Poster:

268 posts

174 months

Thursday 31st May 2012
quotequote all
Hi all, I only recently signed up on PH so firstly, hey there! biggrin, I was just looking for a little advice from you knowledgeable folks :P

I bought a new car number plate recently and am just waiting for the DVLA to issue me with my updated tax disc etc over the next couple of weeks before I can put it on my car, the actual plate has been delivered today and I'm just wondering if anyone could help me out with the best way to drill it to avoid cracking the plates? i.e back to front? small pilot whole first then a larger drill bit maybe?

Any advice would be very much appreciated smile

Thanks

longblackcoat

5,047 posts

214 months

Thursday 31st May 2012
quotequote all
Put bit of gaffa tape over the area you want to drill (front and rear), then a good sharp drill will sort it. No cracking.

HustleRussell

26,708 posts

191 months

Thursday 31st May 2012
quotequote all
Sharp drill bit, moderate speed, very low pressure. Drill from the back to the front, leaving the protective film on the front of the plate until it's ready to screw on. I've never done a pilot hole but no harm in doing so I suppose.

Chicane-UK

3,861 posts

216 months

Thursday 31st May 2012
quotequote all
I've previously used the sticky pads instead of drilling. Use enough of them and no amount of force will remove the plate! Not too keen on drilling holes in body work TBH!

Tyy

Original Poster:

268 posts

174 months

Thursday 31st May 2012
quotequote all
Great, thanks very much for the quick response, I'll give it a go and see how it turns out smile

fflyingdog

621 posts

270 months

Thursday 31st May 2012
quotequote all
Chicane-UK said:
I've previously used the sticky pads instead of drilling. Use enough of them and no amount of force will remove the plate! Not too keen on drilling holes in body work TBH!
Sticky pads work well,agree with Mr Chicane-UK

Guffy

2,372 posts

296 months

Thursday 31st May 2012
quotequote all
Just to reiterate, drill from the back, otherwise the backing material will de-laminate!

HustleRussell

26,708 posts

191 months

Thursday 31st May 2012
quotequote all
Yup. Another tip is to drill the new plate 'through' the old one- I.e use the old one as a jig to ensure the holes are in exactly the right place.

Tyy

Original Poster:

268 posts

174 months

Thursday 31st May 2012
quotequote all
Chicane-UK said:
I've previously used the sticky pads instead of drilling. Use enough of them and no amount of force will remove the plate! Not too keen on drilling holes in body work TBH!
scratchchin I guess that might be worth looking into as well, knowing my luck I would stick it on, step back and it would look wonky though ;( I get the feeling it would be a real pig to shift then D:

mat777

10,714 posts

191 months

Thursday 31st May 2012
quotequote all
And apply masking tape over where the holes will be on both sides, this stops the plastic cracking

Tyy

Original Poster:

268 posts

174 months

Thursday 31st May 2012
quotequote all
HustleRussell said:
Yup. Another tip is to drill the new plate 'through' the old one- I.e use the old one as a jig to ensure the holes are in exactly the right place.
Yeah I saw that on Youtube but the lady drilled into stone underneath which didn't seem to smart haha.

http://www.youtube.com/watch?v=vKO8Qo8QUN8

mini me

1,451 posts

224 months

Thursday 31st May 2012
quotequote all
All that has been said already, plus use a block of wood on the underside to drill into. Stops the clear plastic cracking.

sparks_E39

12,738 posts

244 months

Thursday 31st May 2012
quotequote all
Mine are stuck on... they won't be coming off without some effort!

andrew

10,366 posts

223 months

Thursday 31st May 2012
quotequote all
try and adjust the plate height so that the screws don't pierce the edge of a letter wink

and buy some black/white/yellow screw covers !

2 sMoKiN bArReLs

32,045 posts

266 months

Thursday 31st May 2012
quotequote all
Chicane-UK said:
I've previously used the sticky pads instead of drilling. Use enough of them and no amount of force will remove the plate!
Me too.

LaurasOtherHalf

21,429 posts

227 months

Thursday 31st May 2012
quotequote all
oh & if you're using a battery drill with a keyless chuck just make sure the drill bit is in the chuck as tight as possible.

if the drill bit jams in the hole it will delaminate it straight away.

yeah ask me how i know rolleyes

so, to recap...

keep protective film on new plate.

put a bit of masking tape in the area of the holes.

put the old plate on top of the new one & mark the holes.

put the drill bit in the chuck tight!!!

place the new plate on a block of wood.

spin the drill up to a good highish speed.

drill through in one motion & pull the drill bit out whilst still turning

repeat

stand back & bask in the knowledge that yeah, you do your own work on your cars wink

Tyy

Original Poster:

268 posts

174 months

Thursday 31st May 2012
quotequote all
LaurasOtherHalf said:
stand back & bask in the knowledge that yeah, you do your own work on your cars wink
Lol thanks for the info but I have a horrible feeling that I'll stand back in the knowledge that I should have paid someone else to do it laugh

andrew said:
try and adjust the plate height so that the screws don't pierce the edge of a letter wink
It's few enough letters that I don't have to worry about that coolthumbup

MrReg

1,939 posts

253 months

Thursday 31st May 2012
quotequote all
If you're not certain what to do Halfords will stick three sticky pads on the reverse of your new plate and attach it to your old plate for just £14.99 plus the sticky pads. Bargain!

andrew

10,366 posts

223 months

Thursday 31st May 2012
quotequote all
MrReg said:
If you're not certain what to do Halfords will stick three sticky pads on the reverse of your new plate and attach it to your old plate for just £14.99 plus the sticky pads. Bargain!
for that "using false plates" look ???

Nedzilla

2,439 posts

205 months

Thursday 31st May 2012
quotequote all
Another vote for sticky pads.Saves damaging the bodywork and as said already if you use enough of them,it would be easier and quicker to steal your plates by unscrewing them!!