E36 328i cam position sensor - talk to me please
E36 328i cam position sensor - talk to me please
Author
Discussion

Daniel1

Original Poster:

2,931 posts

229 months

Tuesday 5th June 2012
quotequote all
Had the car a couple of weeks now and have done 3 or so early morning blasts. The car is averaging about 16-17 mpg on this type of driving which I don't mind but I think is a little low. The car is also a little hesitant below 4k. Not lumpy like I'm off cam, just not as sharp a throttle response and a little hesitant. At and after 4k rpm it can "sometimes" feel like I've come onto vtec - almost - and runs very smoothly to the redline. I must stress that it is subtle. It's analogous to say it feels more like very subtle modern traction control rather then a massive boost dip on a old fashioned turbo charged car.

My Internet forum browsing has pulled up the cam positioning sensor as a possible fault causing these symptoms so I'd thought I'd ask for advice as well as costs ( both for me with a box of spanners and a decent garage) plus other possible tests etc to eliminate the sensor.

4rephill

5,171 posts

209 months

Tuesday 5th June 2012
quotequote all
Could be that the VANOS seals are failing (see here: http://www.beisansystems.com/procedures/vanos_sing... )

Part of that page says:


Symptoms

Cars experience:

Overall loss of torque and power, particularly in the lower RPM range, < 3k. Bogging then surging at 3k RPM. Uneven power distribution and RPM transition. Engine hesitations in the lower RPM range, < 3k. Louder idle and intermittent idle RPM hiccups. Difficult takeoffs. Loss of power and bogging when AC on. Increased fuel consumption.


You need to get the fault codes read before you start replacing parts, to see if there's a code showing exactly what the fault is.

anonymous-user

85 months

Tuesday 5th June 2012
quotequote all
http://www.youtube.com/watch?v=vY28qUcyFVc

seems simple enough?

I think I need to do this too. The error came up, and it sometimes 'skips a beat'? if that makes sense?


There seems to be alot on ebay:

http://www.ebay.co.uk/sch/i.html?_nkw=bmw%20camsha...

But I would always want dealer or a well reputed parts company for bits like this.

Toathus

32 posts

176 months

Tuesday 5th June 2012
quotequote all
When I had a 328 I had a similar issue. Firstly it was hesitant before 3k then after a while it had literally no power under 3k and ran extremely rough.

After checking the forums I came to the conclusion it could be the cam position sensor so replaced it with non genuine sensor from a motor factors. This cured the flat spot but it still didn't feel quite right under 3000rpm and a year later the hesitation had returned.

I decided to replace the sensor again but this time got a OEM sensor from BMW. It was expensive at around £100 but was well worth the money, it entirely transformed the car, engine pulling aggresivley right until the redline coupled with the M50 manifold and hotter cams it felt like a proper performance car.


anonymous-user

85 months

Tuesday 5th June 2012
quotequote all
Toathus said:
I decided to replace the sensor again but this time got a OEM sensor from BMW. It was expensive at around £100 but was well worth the money, it entirely transformed the car, engine pulling aggresivley right until the redline coupled with the M50 manifold and hotter cams it felt like a proper performance car.
is that video i posted the one you did?


Toathus

32 posts

176 months

Tuesday 5th June 2012
quotequote all
duckhunt said:
is that video i posted the one you did?
Yeah that's the one. Was a bit of a bugger getting it plugged in by the engine but simple enough to do

OldSkoolRS

7,296 posts

210 months

Tuesday 5th June 2012
quotequote all
My Z3 3.0 was like this when I bought it. I bought the INPA software and a cable and found that the exhaust camshaft sensor was generating faults. I bought the dearer of the two options (£42 approx) from my local GSF and fitted that after clearing the faults again and resetting the ECU. The car is much more lively at the lower end and mpg is a little improved too (though I'm using the extra power so not gaining so much mpg as I could smile ). I think the inlet sensor was more expensive, but without the cable & software I would have had to guess at which one was faulty, so the software paid for itself first time out.

Daniel1

Original Poster:

2,931 posts

229 months

Tuesday 5th June 2012
quotequote all
OldSkoolRS said:
My Z3 3.0 was like this when I bought it. I bought the INPA software and a cable and found that the exhaust camshaft sensor was generating faults. I bought the dearer of the two options (£42 approx) from my local GSF and fitted that after clearing the faults again and resetting the ECU. The car is much more lively at the lower end and mpg is a little improved too (though I'm using the extra power so not gaining so much mpg as I could smile ). I think the inlet sensor was more expensive, but without the cable & software I would have had to guess at which one was faulty, so the software paid for itself first time out.
Where do I get hold of the software and lead? I will google it but if you have any experience that would be helpful I'd appreciate it.

OldSkoolRS

7,296 posts

210 months

Tuesday 5th June 2012
quotequote all
I got mine from this place (the £34.99 option with the 20 pin to 16 pin adaptor):

http://bmwcables.moonfruit.com/

It comes with detailed instructions to install the INPA and also DIS/SSS software (though I've only installed the INPA software as it does everything such as ECU, airbag and ABS resets and fault codes).