Does £260 all in sound about right for this for my E39?
Does £260 all in sound about right for this for my E39?
Author
Discussion

sparks_E39

Original Poster:

12,738 posts

244 months

Saturday 30th June 2012
quotequote all
New water pump and viscous coupling, fitted. It isn't broke yet but I dare not leave it any longer really. Price is from an indie.

steve_bmw

1,591 posts

206 months

Saturday 30th June 2012
quotequote all
I would pay that if I couldn't DIY it, probably £100 worth of parts and a couple of hours labour. Its expensive but not a complete rip off.

sparks_E39

Original Poster:

12,738 posts

244 months

Saturday 30th June 2012
quotequote all
Parts are about £160, it's beyond my DIY ability.

E30M3SE

8,493 posts

227 months

Saturday 30th June 2012
quotequote all
Whilst drained down I'd do the 'stat as well and check condition of all the hoses.

sparks_E39

Original Poster:

12,738 posts

244 months

Saturday 30th June 2012
quotequote all
The thermostat was replaced in 2009 as well as the radiator and hoses.

joe_90

4,206 posts

262 months

Saturday 30th June 2012
quotequote all
About 80ish for the parts (from eBay), an it's really easy to do yourself, will take about 3 hours the first time, I could prob do it in about under 2 now..

Note, this was on my e36 track car, it honestly and easy job.

sparks_E39

Original Poster:

12,738 posts

244 months

Saturday 30th June 2012
quotequote all
I wouldn't trust cheaper components for the cooling system I'm afraid. Everything I buy for the car is either OEM or has trusted positive reviews over the last few years. It cost's a fair bit doing it that way but it gives me peace of mind. This new pump and viscous coupling has a metal fan rather than plastic. I can do simple things like brakes, filters and oil changes, but don't trust my ability to start fixing bits of the engine. Especially that if the engine overheats once, it's pretty much fooked.

Edited by sparks_E39 on Saturday 30th June 19:58

pits

6,704 posts

221 months

Sunday 1st July 2012
quotequote all
sparks_E39 said:
Parts are about £160, it's beyond my DIY ability.
Can you operate a screw driver?
Can you operate a spanner and a hammer?
Can you operate a ratchet?
It is a 30 minute job.
Undo top hoses.
Unclip expanding rivets on radiator housing, but don't pop out yet
Buy a sink/bath spanner 32/34mm put it on viscous fan nut, hit it with a hammer really fking hard clockwise, undo fan by spinning it.
Take belts off remembering where they run (pry bar of sorts on tensioners)
Undo thermostat housing,
Undo water pump housing
replace, refit, make sure you fit a metal water pump..

Seriously, 20 minutes if you know what you're doing, 2 hours if not, once the fan is off which is one nut you can see and reach everything.

eliot

11,999 posts

285 months

Sunday 1st July 2012
quotequote all
sparks_E39 said:
The thermostat was replaced in 2009 as well as the radiator and hoses.
Ready for a new one then!

joe_90

4,206 posts

262 months

Sunday 1st July 2012
quotequote all
pits said:
sparks_E39 said:
Parts are about £160, it's beyond my DIY ability.
Can you operate a screw driver?
Can you operate a spanner and a hammer?
Can you operate a ratchet?
It is a 30 minute job.
Undo top hoses.
Unclip expanding rivets on radiator housing, but don't pop out yet
Buy a sink/bath spanner 32/34mm put it on viscous fan nut, hit it with a hammer really fking hard clockwise, undo fan by spinning it.
Take belts off remembering where they run (pry bar of sorts on tensioners)
Undo thermostat housing,
Undo water pump housing
replace, refit, make sure you fit a metal water pump..

Seriously, 20 minutes if you know what you're doing, 2 hours if not, once the fan is off which is one nut you can see and reach everything.
It is really that easy, bleeding can be a bit troublesome, just take your time to stop air bubbles, and you can get the big spanner from halfords. (not the fan is a left thread)

Fox-

13,578 posts

277 months

Sunday 1st July 2012
quotequote all
The parts are more than 80 quid because you need to use a genuine viscous coupling as the aftermarket ones are totally rubbish and tend not to function correctly.

joe_90

4,206 posts

262 months

Sunday 1st July 2012
quotequote all
Fox- said:
The parts are more than 80 quid because you need to use a genuine viscous coupling as the aftermarket ones are totally rubbish and tend not to function correctly.
Maybe, mine was real bmw on ebay, its stamped with the correct marking and came in the right box..(so i think its legit, it may be) anyways.. its on my track car, so makes no odds, some track cars (e36's) run with no fan at all.. its not needed really.

sparks_E39

Original Poster:

12,738 posts

244 months

Sunday 1st July 2012
quotequote all
eliot said:
Ready for a new one then!
I reckon those components have life left in them, they have.only done 25k!

pits

6,704 posts

221 months

Monday 2nd July 2012
quotequote all
joe_90 said:
It is really that easy, bleeding can be a bit troublesome, just take your time to stop air bubbles, and you can get the big spanner from halfords. (not the fan is a left thread)
Depends how you fill it up, I had no air bubbles
igntion on
heaters on
fill through the top hose into block till it starts coming out the top hose
Fill through bottom hose into radiator till it is full
start car heaters on full whack, and leave the bleed nipples open slightly.

Whilst you are at it, may I advise you buy 2 new bleed nipples one for radiator and one for thermostat housing as they tend to have got a bit hot, and undoing them destroys them if you use wrong screwdriver.
BMW part no. Vent screw 17111712788


This is how the belts go


Seriously though it is so easy a child can do it (to a point)

As for the spanner, go to some sort of plumbing centre and they should sell a bath spanner, 32mm one side 34mm other side, slightly cheaper than Halfords I would imagine.


Actually it is a really good "technical job" to get your teeth into, it isn't hard, there is no real way you can balls it up and you feel like you have achieved something

Fox-

13,578 posts

277 months

Monday 2nd July 2012
quotequote all
I dont think its fair to say there is no way you can balls up work which involves the cooling system on an E39. There really is - its not like messing up fitting a parking sensor or something.

pits

6,704 posts

221 months

Monday 2nd July 2012
quotequote all
Fox- said:
I dont think its fair to say there is no way you can balls up work which involves the cooling system on an E39. There really is - its not like messing up fitting a parking sensor or something.
Explain? I managed to do it first time without ballsing it up, and my E34 they are epically simple if you can wield a spanner and a hose pipe.

Fox-

13,578 posts

277 months

Monday 2nd July 2012
quotequote all
pits said:
Explain? I managed to do it first time without ballsing it up, and my E34 they are epically simple if you can wield a spanner and a hose pipe.
If you make a mistake or you don't bleed it properly or whatever the consequences can be an overheating engine. I'm not saying its hard, I'm saying its inaccurate to say you can't balls it up because you can - you can go quite badly wrong.

sparks_E39

Original Poster:

12,738 posts

244 months

Monday 2nd July 2012
quotequote all
I agree with Fox, one overheat and that's likely to kill it, £1000+ for a replacement engine to be sourced and fitted.

Fox-

13,578 posts

277 months

Monday 2nd July 2012
quotequote all
Rightly or wrongly as soon as I see a task on my car involves coolant it goes to somebody else to do for me, I cannot be bothered with the faff of bleeding it etc etc and the cooling system is bad enough as it is without me adding to the problems hehe

sparks_E39

Original Poster:

12,738 posts

244 months

Monday 2nd July 2012
quotequote all
Yes, as I mentioned earlier I find brakes, oil and filter changes easy enough but work on the engine, on a part of it that really is quite fragile isn't something I'm confident about.