E36 328i Suspension overhaul, what else do I need?
Discussion
Hi all, soon when I can get enough funds together the 'underneath' is getting a refresh.
I have done control arms/bushes/tie rods etc before on e36/e46's.
This is the first time I've done shocks/springs, so It would be great if anyone could help me
with a 'shopping list' for the little parts that go with shocks (top mounts? etc)
Probably going to go for a set of B12's
(OEM B8 with Eibch prokit, dont want it too low!)
http://www.larkspeed.com/index.pl?p=5746180957&...
Front lower control arms
Droplinks
Tie/ Steering rods
Poly bushes front and rear.
Also any recommendations for where to get these? I've always used allgermanparts, they're normally excellent service/ price.
Just need some help with the other bits that would want doing at the top of the strut?
Thanks alot.
I have done control arms/bushes/tie rods etc before on e36/e46's.
This is the first time I've done shocks/springs, so It would be great if anyone could help me
with a 'shopping list' for the little parts that go with shocks (top mounts? etc)
Probably going to go for a set of B12's
(OEM B8 with Eibch prokit, dont want it too low!)
http://www.larkspeed.com/index.pl?p=5746180957&...
Front lower control arms
Droplinks
Tie/ Steering rods
Poly bushes front and rear.
Also any recommendations for where to get these? I've always used allgermanparts, they're normally excellent service/ price.
Just need some help with the other bits that would want doing at the top of the strut?
Thanks alot.
Also if anyone could help,
If I go a little too 'enthusiastically' on a bend, instead of breaking traction/tyre squeal,
I get a horrendous vibration, like a jackhammer on the rear axle. ASC off.
Obviously I dont do this, but on bumpy roads too its really bad.
Is that going to be Reat trailing arm bush? Or are there other parts of the rear suspension, Im not 100% familiar with it.
But somethings definatley not right and I need to sort it,
Thanks.
If I go a little too 'enthusiastically' on a bend, instead of breaking traction/tyre squeal,
I get a horrendous vibration, like a jackhammer on the rear axle. ASC off.
Obviously I dont do this, but on bumpy roads too its really bad.
Is that going to be Reat trailing arm bush? Or are there other parts of the rear suspension, Im not 100% familiar with it.
But somethings definatley not right and I need to sort it,
Thanks.
Captain Cadillac said:
Could be RTABs, but I'd check where the diff mounts to the bodyshell, very carefully. They're known for structural failures back there, requires dropping the diff (easy, but it's kinda heavy) and welding in repair plates.
Oh dear, that doesn't sound good.Just browsing for a kit to get an idea, mostly US. Is that the subframe kit?
http://www.vacmotorsports.com/catalog/vac---e36-re...
or something different.
duckhunt said:
Oh dear, that doesn't sound good.
Just browsing for a kit to get an idea, mostly US. Is that the subframe kit?
http://www.vacmotorsports.com/catalog/vac---e36-re...
or something different.
That's it. I don't remember the Euro spec bodyshells being substantially different back there other than Euro M3s (US Spec E36 M3s are unique to N America... Basically a 332is)Just browsing for a kit to get an idea, mostly US. Is that the subframe kit?
http://www.vacmotorsports.com/catalog/vac---e36-re...
or something different.
FWIW, those are factory BMW parts, and Turner sells them for less. Those are us spec M3 subframe mount plates.
Cool,
trouble is welding is a different game, Il have to get that done in a shop. Il have to inspect it all first.
I've done a bit more reading on other sites and there are similar symptoms ranging from RTABs, subframe bushings, flex disc (donut) etc.
Probably worth me doing these with the suspension.
Anyone help on a 'shopping list'?
trouble is welding is a different game, Il have to get that done in a shop. Il have to inspect it all first.
I've done a bit more reading on other sites and there are similar symptoms ranging from RTABs, subframe bushings, flex disc (donut) etc.
Probably worth me doing these with the suspension.
Anyone help on a 'shopping list'?
duckhunt said:
Cool,
trouble is welding is a different game, Il have to get that done in a shop. Il have to inspect it all first.
I've done a bit more reading on other sites and there are similar symptoms ranging from RTABs, subframe bushings, flex disc (donut) etc.
Probably worth me doing these with the suspension.
Anyone help on a 'shopping list'?
As you've got poly bushes on the list you presumably want to tighten it up a bit? Have you considered an X- brace as a cheap addition?trouble is welding is a different game, Il have to get that done in a shop. Il have to inspect it all first.
I've done a bit more reading on other sites and there are similar symptoms ranging from RTABs, subframe bushings, flex disc (donut) etc.
Probably worth me doing these with the suspension.
Anyone help on a 'shopping list'?
As you will know there is loads you can do to the E36s
Firstly I'd check out the problem you are getting first, as mentioned it could be the diff carrier bushes or rtabs
If its the former then I'd just replace them with standard bushes if its the latter then I'd recommend poly bushes, fitting poly bushes to the rtabs won't affect the ride quality too much where as the diff carrier bushes will
If it is the dreaded cracks in the floor don't worry too much its not a massive job to fix just time consuming and not a nice to do if your working on the ground
BMW sell the strengthening plates that are fitted to the M3s for about £60
For the front end I'd recommend fitting E30 wishbones , they bolt straight on and will give a sharper turn in and should you need to replace the outer ball joints its a easier job as they are solid mounted
For the lollipop bushes I'd recommend poly bushes but however i'd recommend the offset ones that are fitted to the 3.0 M3s they will go well with the E30 wishbones and really help the turn in and self centering
As previously said a X-brace will stiffen up the front end you will need to get captive nuts and bolts, I had to enlargen the holes in the subframe slightly to fit them and you can still fit a upper strut brace should you wish
For the rear end uprated top mounts are recommended also Z3 reinforcement plates are a good move whilst you have the rear end apart
Firstly I'd check out the problem you are getting first, as mentioned it could be the diff carrier bushes or rtabs
If its the former then I'd just replace them with standard bushes if its the latter then I'd recommend poly bushes, fitting poly bushes to the rtabs won't affect the ride quality too much where as the diff carrier bushes will
If it is the dreaded cracks in the floor don't worry too much its not a massive job to fix just time consuming and not a nice to do if your working on the ground
BMW sell the strengthening plates that are fitted to the M3s for about £60
For the front end I'd recommend fitting E30 wishbones , they bolt straight on and will give a sharper turn in and should you need to replace the outer ball joints its a easier job as they are solid mounted
For the lollipop bushes I'd recommend poly bushes but however i'd recommend the offset ones that are fitted to the 3.0 M3s they will go well with the E30 wishbones and really help the turn in and self centering
As previously said a X-brace will stiffen up the front end you will need to get captive nuts and bolts, I had to enlargen the holes in the subframe slightly to fit them and you can still fit a upper strut brace should you wish
For the rear end uprated top mounts are recommended also Z3 reinforcement plates are a good move whilst you have the rear end apart
Edited by disco!!!! on Sunday 23 September 16:02
Gassing Station | BMW General | Top of Page | What's New | My Stuff


