Removing Links / Adjusting Bracelet
Discussion
_Nathan_ said:
Not in this situation, the other side of the link is completely molded.
Googling about, there are other people who solved the problem by inserting a flat head screw driver inbetween the link and smashing it with a hammer !
You could't fit the smallest of screwdrivers in there.
That sounds a bit drastic! If the screw is spinning then it suggests that the thread itself may be stripped, but perhaps a slight bend is preventing the screw from coming free. Sounds like there is going to be some sacrifice required on the bracelet's part whatever happens...Googling about, there are other people who solved the problem by inserting a flat head screw driver inbetween the link and smashing it with a hammer !
You could't fit the smallest of screwdrivers in there.
If it's Chinese fake Sub-type bracelet, it might be easier to buy another one on eBay, and swap the whole thing.
If the screw is turning both ways, but the head is in the fully-screwed-in position, then the thread is damaged. Quite possibly came out of the factory like that. If it's the link that's riveted to the clasp, there's not much you can do. Even if you cut it off with a hacksaw, you won't be able to put it back together, as the thread in the link is probably damaged, as well as the thread on the screw.
If the screw is turning both ways, but the head is in the fully-screwed-in position, then the thread is damaged. Quite possibly came out of the factory like that. If it's the link that's riveted to the clasp, there's not much you can do. Even if you cut it off with a hacksaw, you won't be able to put it back together, as the thread in the link is probably damaged, as well as the thread on the screw.
CardShark said:
Looking at the bracelet style, the case back and the shape of the case itself I'd guess at it being more than a fake bracelet.
It could be an homage - Steinhart (although the bracelet quality would be a lot better), Alpha, Invicta, etc. - or even a self-build.Might even be a real Sub with a Chinese bracelet.
I've got a fake bracelet on my Sub. I needed to remove an extra (riveted) link from the bracelet of my 14060, as i have small wrists, and the clasp wouldn't sit centrally on the back of my wrist.
Rather than butcher the original, I bought a fake (with no logo) on eBay. Hacksawed off one of the fixed links, and fitted the original Rolex clasp. So, it's a genuine watch and clasp, with fake links.
You are probably right, though!
It's not a screw - its a split pin.
You're looking at the end of the split pin (which looks like flat head screw).
They're very hard to get out, you'll need the wee tool you can find on Amazon - its like a mini vice that screws a small pin on top of the split pin and forces it out. Not expensive to buy and useful for the next strap.
Actually - edit. Looking more closely at your pics, it does look more like a screw!!
You're looking at the end of the split pin (which looks like flat head screw).
They're very hard to get out, you'll need the wee tool you can find on Amazon - its like a mini vice that screws a small pin on top of the split pin and forces it out. Not expensive to buy and useful for the next strap.

Actually - edit. Looking more closely at your pics, it does look more like a screw!!
NDA said:
It's not a screw - its a split pin.
You're looking at the end of the split pin (which looks like flat head screw).
They're very hard to get out, you'll need the wee tool you can find on Amazon - its like a mini vice that screws a small pin on top of the split pin and forces it out. Not expensive to buy and useful for the next strap.
That was my first thought.You're looking at the end of the split pin (which looks like flat head screw).
They're very hard to get out, you'll need the wee tool you can find on Amazon - its like a mini vice that screws a small pin on top of the split pin and forces it out. Not expensive to buy and useful for the next strap.

However, the OP says that the other side of the link is "completely moulded", which I take to mean that it's a blind hole. If it was a split pin, there would be a hole on both sides of the link to allow the pin to be pushed out.
Gassing Station | Watches | Top of Page | What's New | My Stuff



