Mondeo st
Author
Discussion

Teejay1988

Original Poster:

13 posts

163 months

Tuesday 9th April 2013
quotequote all
Good afternoon all

I'm after a little feed back on my ford mondeo st not starting starting its on a 2007 plate and the 2.2 diesel.

It's got no fuel going to the injectors and no signs of metal swarf on the top of the injectors. Also the battery has been dissconnect for a day or two there was a code logged it was P0251 I think off the top of my head, which does relate to the fuel system do I need reprogram anything or is a fault on the vehicle.

Any information should helpful thank Teejay.

philmots

4,666 posts

291 months

Tuesday 9th April 2013
quotequote all
Fuel pump?

Teejay1988

Original Poster:

13 posts

163 months

Tuesday 9th April 2013
quotequote all
Is there any way of bypassing the electrical system to start the engine?

v64paul

120 posts

252 months

Tuesday 9th April 2013
quotequote all
Rail pressure needs to be at a certain level before injection is attempted. If no obvious leaks then it's fuel pump time, which in turn means that the injectors WILL be fubar.

Teejay1988

Original Poster:

13 posts

163 months

Tuesday 9th April 2013
quotequote all
There no fuel going to the injectors at all I've loosened the high pressure pipes and it not even attempting to create pressure.
Also the fuel pump shouldn't need timing if its common rail should it?

Teejay1988

Original Poster:

13 posts

163 months

Tuesday 9th April 2013
quotequote all
There no fuel going to the injectors at all I've loosened the high pressure pipes and it not even attempting to create pressure.
Also the fuel pump shouldn't need timing if its common rail should it?

v64paul

120 posts

252 months

Tuesday 9th April 2013
quotequote all
In the simplest terms, the pump won't develop any kind of pressure it there is a leak, real or artificial like opening the high pressure connection at the pump or the fuel rail. No, timing isn't critical, it is what it is; a pump. The ECU controls duration and timing of injection by telling the injectors when to open. I really do reccomend gathering as much info as possible before going ahead. Usually though there really only are the usual reasons for failure of this sort. As an observation, don't try and tow start the car as you will risk killing the dual mass flywheel too.

Steffan

10,362 posts

259 months

Tuesday 9th April 2013
quotequote all
v64paul said:
In the simplest terms, the pump won't develop any kind of pressure it there is a leak, real or artificial like opening the high pressure connection at the pump or the fuel rail. No, timing isn't critical, it is what it is; a pump. The ECU controls duration and timing of injection by telling the injectors when to open. I really do reccomend gathering as much info as possible before going ahead. Usually though there really only are the usual reasons for failure of this sort. As an observation, don't try and tow start the car as you will risk killing the dual mass flywheel too.
Good advice. Tow starting and using booster packs is no longer a simple job with the increased complexity of electrical and mechanical systems in cars in recent years. Without a doubt car electricians are going to be the master class in car mechanics in the future. The effects of remapping are only the begginings of the changes that will come. Dial up tuning is on its way.

Steve_F

881 posts

225 months

Tuesday 9th April 2013
quotequote all
Where did you buy it? Wonder if it's my old one as I had a few fears something like that might happen!

Teejay1988

Original Poster:

13 posts

163 months

Tuesday 9th April 2013
quotequote all
From Glasgow

Steve_F

881 posts

225 months

Tuesday 9th April 2013
quotequote all
The reg plate doesn't start NJ07 does it??

Hoping not but there was nothing I could put my finger on that made me suspect it might end up doing something like that.

Complicated diesel engines are just a headache. No ideas what could be wrong with it though :-(

Teejay1988

Original Poster:

13 posts

163 months

Tuesday 9th April 2013
quotequote all
No mate DK07 thanks for making me feel better tho

nipsips

1,167 posts

166 months

Tuesday 9th April 2013
quotequote all
Pumps on these are coded. They are also fairly common to fail. Along with injectors. Rails etc etc. Modern diesels are sadly not very reliable when they start to rack up the miles.

Teejay1988

Original Poster:

13 posts

163 months

Tuesday 9th April 2013
quotequote all
Is it possible that I have lost the code by dissconnecting the battery?

nipsips

1,167 posts

166 months

Tuesday 9th April 2013
quotequote all
Very very unlikely if im honest. The pumps a complete assembly from Ford - although there is a metering valve and a temperature sensor available seperately. My advice would be get it onto Ford's IDS - this will allow them to give you a bit more information. The only downside is there can often be more than one fault frown

mdm1uk

1,344 posts

179 months

Tuesday 9th April 2013
quotequote all
Dont want to state the Obvious but but could this be an immobiliser issue as the battery was out for two days ?

nipsips

1,167 posts

166 months

Tuesday 9th April 2013
quotequote all
Again the keys just wouldnt lose the code because power is lost. It wouldnt crank if the immobiliser had kicked in - would just flash the clock light repeatedly. Im guessing its cranking or its pointless cracking the HP pipes off the injectors to see if diesel is flowing.

The only saving grace the OP may have is a blocked fuel filter possibly? Id change that first and foremost with any diesel running issue.

Teejay1988

Original Poster:

13 posts

163 months

Wednesday 10th April 2013
quotequote all
Is there a solenoid controlling the fuel pressure on a mondeo st 155 2007 model

nipsips

1,167 posts

166 months

Saturday 13th April 2013
quotequote all
Theres a fuel pressure sensor on the common rail fuel rail, however this is part of the rail.