How to remove rusted bolt without shearing?
How to remove rusted bolt without shearing?
Author
Discussion

youngsyr

Original Poster:

14,742 posts

223 months

Monday 22nd April 2013
quotequote all
Hi all, I'm hoping to get some advice on removing a very rusty bolt from my 14 year old MX-5. It's a 10mm hex head bolt that holds the headlight bracket on. When I removed the one on the other side, I managed to shear it with just a tiny little 6" long spanner and a moderate amount of force.

So far I've bathed it in WD40 and I can't use heat because it holds the plastic headlight bracket to the front cross member.

Any help gratefully appreciated... smile

Also, any help on getting the sheared bolt on the otherside out would also be appreciated - I take it it's a drill and bolt extractor job?




OdramaSwimLaden

1,971 posts

200 months

Monday 22nd April 2013
quotequote all
Beat it as hard as you dare with a large hammer to shock it into un seizing itself.

It's often worked for me.

garycat

5,439 posts

241 months

Monday 22nd April 2013
quotequote all
Impact driver?

Monty Python

4,813 posts

228 months

Monday 22nd April 2013
quotequote all
Try oil rather than WD40 - that's really aimed at displacing water rather that lubrication.

MGgeordie

939 posts

215 months

Monday 22nd April 2013
quotequote all
14 year old? Wait till its 24 year old like my MX5! biggrin

Only thing I suggest is letting it soak for a couple of days in some decent penetrating fluid, WD40 may not be good enough to be honest. I used to have some but can remember the name of it, sorry.

Jacobyte

4,768 posts

273 months

Monday 22nd April 2013
quotequote all
PlusGas is what you should be using, not WD40.

V8mate

45,899 posts

220 months

Monday 22nd April 2013
quotequote all
Monty Python said:
Try oil rather than WD40 - that's really aimed at displacing water rather that lubrication.
Plus Gas.

conkerman

3,520 posts

166 months

Monday 22nd April 2013
quotequote all
Get a bit of heat on it if you can.

Remove bolt using a backwards/forwards motion. Be gentle. If it suddenly feels like it is loosening up STOP!

Or Just rip the head off it and deal with it later.

Dr Interceptor

8,183 posts

227 months

Monday 22nd April 2013
quotequote all
http://www.halfords.com/webapp/wcs/stores/servlet/...

This stuff has been a god send working on the 1936 Vauxhall biggrin

SuperchargedVR6

3,138 posts

251 months

Monday 22nd April 2013
quotequote all

youngsyr

Original Poster:

14,742 posts

223 months

Monday 22nd April 2013
quotequote all
doogz said:
Impact. Know anyone with a compressor, or battery powered/12V impact wrench?
Good call - I completely forgot that I have one myself.paperbag

Thanks for the tips everyone, I'll get some decent penetrating oil, bathe it for a few days and then have a go with the impact wrench.

youngsyr

Original Poster:

14,742 posts

223 months

Monday 22nd April 2013
quotequote all
SuperchargedVR6 said:
Thanks but that just helps you grip a mangled bolt head, I suspect?

The bolt head is fine (and the one I sheared on the other side is just the stem, so too small and not proud enough for those).


Robb F

4,614 posts

202 months

Monday 22nd April 2013
quotequote all
SuperchargedVR6 said:
How's that going to help?

Just let it shear then drill the old bolt out.

youngsyr

Original Poster:

14,742 posts

223 months

Monday 22nd April 2013
quotequote all
Robb F said:
How's that going to help?

Just let it shear then drill the old bolt out.
How would you do this - I have reasonably powerful drills (500w?) and the reverse threaded bolt extractors bits, but how do you actually drill a hole in the old bolt's stem?

Presumably you need the right drill bit, as all the ones I've ever tried barely scratch the surface of steel?

Robb F

4,614 posts

202 months

Monday 22nd April 2013
quotequote all
You just need a decent metal drillbit and a normal battery drill. Put a centre dot in bolt to ensure it drills where you want it to, plenty of pressure so you don't just rub the top of the metal and work harden it and drill away. Non structural bolts are made from pretty soft metal.

Sogra

471 posts

242 months

Monday 22nd April 2013
quotequote all
Use a cobalt drill bit (expensive) and then use screw extractor, but try plus Gaz first its brilliant.

Captain Muppet

8,540 posts

296 months

Monday 22nd April 2013
quotequote all
PlusGas has seriously reduced the grief of working on my 21 year old MX5. Although I'm running out of bolts to undo that I haven't already undone in the last 6 years.


I've just realised that if the MX5 lasts another year it'll be in joint first place as my longest serving car. Blimey. Not bad for a shed I bought as a temporary track hack.

RizzoTheRat

29,153 posts

223 months

Monday 22nd April 2013
quotequote all
You say a plastic headlight bracket, is the bolt screwing in to plastic or in to a captive nut? If it's plastic you then WD40 or other mineral oils might cause it to swell and grip the bolt even harder.

Plus gas is definitly worth a shot, and a few mates have said the halfords shock and unlock spray works well, it's penetrating oil that cools the metal as well.

BliarOut

72,863 posts

270 months

Monday 22nd April 2013
quotequote all
If you can get to the threads wire brush them. Another top tip, it's often easier to tighten it a fraction before you start to loosen. Try loosening a little then tightening a fraction less, this helps work the detritus out of the threads.

Monty Python

4,813 posts

228 months

Tuesday 23rd April 2013
quotequote all
RizzoTheRat said:
You say a plastic headlight bracket, is the bolt screwing in to plastic or in to a captive nut? If it's plastic you then WD40 or other mineral oils might cause it to swell and grip the bolt even harder.

Plus gas is definitly worth a shot, and a few mates have said the halfords shock and unlock spray works well, it's penetrating oil that cools the metal as well.
Swelling only happens with natural rubbers, not hard plastics.