What I want to know is why is my boot light not working!
Discussion
Yeah, on my old Rover 45 ... why is that?
... OK.
So out with the Multimeter and a quick check of the two terminals on the switch which is integral with the boot lock. A healthy 12.7 volts there so no problem there :~

Next, remove the plastic cover for the lock, undo the two 8mm retaining bolts, juggle the lock assembly out of its location in the double skin of the boot lid. Much easier to do that having disconnected the remote cable release and the boot lock key operated release rod too. Then the lock was completely free of its location and could be checked. I suspect someone has had a go this lock in the past. It was loaded with masses of LM type Grease which I cleaned most away to reveal the various moving parts of the lock assembly. Here the lock is in the shut boot position, showing the boot light switch contacts apart so no circuit. The small screwdriver points to this.

So far so good. Then released the lock from the shut position and this showed the switch still not making electrical electrical contact as this closer view clearly shows :~

So, carefully bent the curved brass switch so that it made good contact in the boot lock open position as in this picture. The small screwdriver again points to the contact :~

Reassembled switch prior to putting into the boot lid :~

Then moved the lock to the open position and voila :~

I can see for miles with this baby! :~

All very well clever dick, how do you know it actually goes out when the boot lid is shut?
Here's how. Lower one of the seat backs and observe. First with boot lid shut. That's the lamp light hanging down top centre of picture ~ OFF ..
:~

Now after pulling the boot release lever by the driver's seat ~ It's ON! ..
:~

Sorted! No more groping about in the dark for me ... Oh Matron ...
MGJohn's Conscience said:
.
Then get up off your backside and find out!
.
... Then get up off your backside and find out!
.
... OK.So out with the Multimeter and a quick check of the two terminals on the switch which is integral with the boot lock. A healthy 12.7 volts there so no problem there :~

Next, remove the plastic cover for the lock, undo the two 8mm retaining bolts, juggle the lock assembly out of its location in the double skin of the boot lid. Much easier to do that having disconnected the remote cable release and the boot lock key operated release rod too. Then the lock was completely free of its location and could be checked. I suspect someone has had a go this lock in the past. It was loaded with masses of LM type Grease which I cleaned most away to reveal the various moving parts of the lock assembly. Here the lock is in the shut boot position, showing the boot light switch contacts apart so no circuit. The small screwdriver points to this.

So far so good. Then released the lock from the shut position and this showed the switch still not making electrical electrical contact as this closer view clearly shows :~

So, carefully bent the curved brass switch so that it made good contact in the boot lock open position as in this picture. The small screwdriver again points to the contact :~

Reassembled switch prior to putting into the boot lid :~

Then moved the lock to the open position and voila :~

I can see for miles with this baby! :~

All very well clever dick, how do you know it actually goes out when the boot lid is shut?
Here's how. Lower one of the seat backs and observe. First with boot lid shut. That's the lamp light hanging down top centre of picture ~ OFF ..
:~
Now after pulling the boot release lever by the driver's seat ~ It's ON! ..
:~
Sorted! No more groping about in the dark for me ... Oh Matron ...

Errr...ok.
As an aside, is that sort of arrangement normal? Most light mechanisms I've come across just have a sprung plastic post (nothing to do with the lock) and when the door/boot is opened, the post is raised and the circuit is completed.
As an aside, is that sort of arrangement normal? Most light mechanisms I've come across just have a sprung plastic post (nothing to do with the lock) and when the door/boot is opened, the post is raised and the circuit is completed.
Edited by Risotto on Tuesday 23 April 21:22
mattley said:
MJK 24 said:
Do you always carry a spare inlet manifold and rear silencer in your boot?
It's a Rover 45, Always worth carrying spares 
Top bit of fixing minor irritations OP!

Normally I carry a spare K-Series 1.8 engine just in case, to be on the safe side. Very wise.

Many folks have advised me that these Rovers and MGs are so unreliable that it's wise to carry a few spares. Good advice that ...

Mind you, in over fifty years of driving these MGs and Rover cars, NEVER had one let me down. Not a one.
I'm a tad superstitious so best to give it mum's the word and all that

Too bluddy late now....
Always a first time though ... 
Here's me back in the middle ages in my second MGB. Well mid 1960s actually ~ swinging sixties, dolly birds, mini skirts and all that.

Youngsters today, don't know theyze born. And I lived in a cardboard box. Was a nice one though.
Risotto said:
Errr...ok.
As an aside, is that sort of arrangement normal? Most light mechanisms I've come across just have a sprung plastic post (nothing to do with the lock) and when the door/boot is opened, the post is raised and the circuit is completed.
Most of my MGs and Rovers have the switch integral to the boot lock. Much the same as the one pictured in this thread. I finally got round to fixing the one in my 620ti after seven years. Managed without it for so long. In previous ownership, whoever worked on the car removed the single boot switch connector from its terminal and refitted it rotated 180 degrees. So only one terminal was connected .. As an aside, is that sort of arrangement normal? Most light mechanisms I've come across just have a sprung plastic post (nothing to do with the lock) and when the door/boot is opened, the post is raised and the circuit is completed.
I cleaned it and refitted it correctly positioned and guess what ... let there be light and you could see for miles ... 
Funny old game folks and their cars. The previous owner of my 620ti entrusted all work on his car to professionals. It came with a massive folder of "history" and plenty of hefty Invoices for work including new brakes fitted a few months before I bought the car. Those pads had been pushed ( hammered ) into there carriers without the brake dust a road crud being thoroughly cleaned away. Net result, one of the lugs became seized unable to slide in the carrier correctly as they should as the pads wear with use. That resulted in fairly new Brake Pads being rendered useless in a few miles. Note the twisted pads and the huge tapered difference in wear of the inboard pad and the almost completely worn away down to the metal of the outboard tapered worn pad.

Hence my maxim from my early days of entrusting the care of my cars to professionals... It is this :~
BEWARE PROFESSIONALS
Not just automotive pros, in all walks of life!
:~
BorkFactor said:
MGJohn said:
Too bluddy right mates ! ... 
Normally I carry a spare K-Series 1.8 engine just in case, to be on the safe side. Very wise.

Normally I carry a spare K-Series 1.8 engine just in case, to be on the safe side. Very wise.


Brilliant!
This has inspired me to investigate why my boot light has forgotten it's purpose in this world, can't be that hard, right?
Gassing Station | General Gassing | Top of Page | What's New | My Stuff



