Intermittent clutch / gearbox problem
Discussion
I'm having an intermittent issue with my car and was just wondering if anyone knew what might be causing it. It's an MX5 1.8 Mk3 with about 67k miles.
The problem is noticeable in two situations, but I wouldn't be surprised if it was the same issue causing both problems.
The most common occurrence is that the car won't go into reverse. It doesn't seem to make a difference whether the car is warmed up or not. The vast majority of the time it's absolutely fine, but occasionally (and what seems to be more frequently recently) the gear lever will only move about half way into reverse before feeling like it's reached the end of its travel. Obviously I haven't forced it any further.
In this kind of situation, sometimes going to fifth, back to neutral and bringing the clutch back up, before trying to put it into reverse again works. Other times this doesn't work, but keeping a light pressure on the gear stick whilst slowly lifting the clutch pedal up results in it 'popping' in to gear without any drama.
The second situation can be where I try to change gear whilst driving and it doesn't quite go into gear. Again, whether the car is warmed up or not doesn't seem to matter nor does the specific gear. It happened yesterday when changing to second but it's happened changing to third and fourth quite recently too. Imagine changing gear with the clutch pedal 'almost' fully depressed and the ensuing grinding of gears and that's pretty much it, except that the clutch pedal is completely depressed.
Aside from these specific issues, the car normally drives fine and there's no odd noises, changes gear fine, etc... Does anyone have any idea what could be causing this?
The fact that it's intermittent is what bugs me. I would have thought if something was mechanically wrong, it would always do it rather than just now and then.
The problem is noticeable in two situations, but I wouldn't be surprised if it was the same issue causing both problems.
The most common occurrence is that the car won't go into reverse. It doesn't seem to make a difference whether the car is warmed up or not. The vast majority of the time it's absolutely fine, but occasionally (and what seems to be more frequently recently) the gear lever will only move about half way into reverse before feeling like it's reached the end of its travel. Obviously I haven't forced it any further.
In this kind of situation, sometimes going to fifth, back to neutral and bringing the clutch back up, before trying to put it into reverse again works. Other times this doesn't work, but keeping a light pressure on the gear stick whilst slowly lifting the clutch pedal up results in it 'popping' in to gear without any drama.
The second situation can be where I try to change gear whilst driving and it doesn't quite go into gear. Again, whether the car is warmed up or not doesn't seem to matter nor does the specific gear. It happened yesterday when changing to second but it's happened changing to third and fourth quite recently too. Imagine changing gear with the clutch pedal 'almost' fully depressed and the ensuing grinding of gears and that's pretty much it, except that the clutch pedal is completely depressed.
Aside from these specific issues, the car normally drives fine and there's no odd noises, changes gear fine, etc... Does anyone have any idea what could be causing this?
The fact that it's intermittent is what bugs me. I would have thought if something was mechanically wrong, it would always do it rather than just now and then.
If this makes any difference: When stopped with the engine off, there are no issues at all in selecting a gear. In fact the gear lever can be moved far easier than it ever is whilst driving.
In comparison, when driving most gears seem to have much more resistance.
Would this be more indicative of a clutch problem than a selector?
In comparison, when driving most gears seem to have much more resistance.
Would this be more indicative of a clutch problem than a selector?
Hydraulic clutch on these if the internet can be believed. Were it a knackered old MG I would say it was a failing seal in either the clutch master or slave cylinder. If that's the case there will possibly be a bit of clutch fluid leaking. Check the level in the reservoir and see if it goes down over the week.
Thanks for the advice:
Gearbox oil: This was changed about a year ago. I'm pretty sure it's not due on the service schedule for another couple of years at least.
Clutch fluid: The reservoir bottle was wet and so 'could' be leaking. But I haven't noticed any wet patches on my drive, and the fluid level is just below the max. mark. I've cleaned it off and will keep an eye on it. The clutch/brake fluid (they share a reservoir) looks completely black, is this normal?
I'm not a very mechanically minded person, but not through lack of trying... So I'll look in to how to bleed the clutch and see if it makes any difference.
Gearbox oil: This was changed about a year ago. I'm pretty sure it's not due on the service schedule for another couple of years at least.
Clutch fluid: The reservoir bottle was wet and so 'could' be leaking. But I haven't noticed any wet patches on my drive, and the fluid level is just below the max. mark. I've cleaned it off and will keep an eye on it. The clutch/brake fluid (they share a reservoir) looks completely black, is this normal?
I'm not a very mechanically minded person, but not through lack of trying... So I'll look in to how to bleed the clutch and see if it makes any difference.

Gassing Station | General Gassing | Top of Page | What's New | My Stuff


