Breaking the bond: Alloy wheel removal
Breaking the bond: Alloy wheel removal
Author
Discussion

eltax91

Original Poster:

10,799 posts

237 months

Monday 29th April 2013
quotequote all
Hi guys. Recently picked up a daily driver of an e61 5 series. The iDrive has been nagging at me to sort the rear brake pads, so I got onto ECP's site and got some kit delivered and set to over the weekend.

So, I found the crappy plastic jack point and got it in the air. The undercarriage is a vast display of plastic so I'm struggling to find somewhere to put the axle stand. I opted to remove the wheel, place it under the sill and then find somewhere suitable.

Therein lies the trouble. I couldn't even get the bloody wheel off! Undid the bolts no worries, but clearly they have never been greased or treated at any point, so are stuck solid to the hub.

Of course I really need them off, so I hit it with my biggest (rubber) hammer, but that didn't work.

So, DIY people of PH, how do I get it off when it's on the relatively unstable trolley jack? Any tips or tricks?

biggrin

Adam_W

1,098 posts

231 months

Monday 29th April 2013
quotequote all
take all the bolts out, wind 2 or 3 back in a few turns then drop the car with the jack, ping 1 wheel released, jack back up and remove.

eltax91

Original Poster:

10,799 posts

237 months

Monday 29th April 2013
quotequote all
Adam_W said:
take all the bolts out, wind 2 or 3 back in a few turns then drop the car with the jack, ping 1 wheel released, jack back up and remove.
Hmmm. You will love this but I tried that!! Although I didn't take it all the way off the jack as I was worried about causing havoc. Might have another crack tomorrow then.

How far would you drop the bolts back in? Just a quarter of the thread or so?

Krikkit

27,943 posts

212 months

Monday 29th April 2013
quotequote all
Give them a few turns, make sure they're seated - that won't be enough to hold it on fully, which is what you want. smile

jas xjr

11,309 posts

270 months

Monday 29th April 2013
quotequote all
Adam_W said:
take all the bolts out, wind 2 or 3 back in a few turns then drop the car with the jack, ping 1 wheel released, jack back up and remove.
i had this a few weeks ago . i drove it back and forth a couple of times too

P I Staker

3,308 posts

187 months

Monday 29th April 2013
quotequote all
Kick it.

Hit either side of the wheel alternatively with the palms of your hands.

Get a hammer and a block of wood and knock them off.

sim16v

2,177 posts

232 months

Monday 29th April 2013
quotequote all
Or put all 5 back in, about half way, then drive 10 yards up and down the road.


Emeye

9,781 posts

254 months

Monday 29th April 2013
quotequote all
I had this problem with my old mx5. I lay under the car and kicked the wheel off using my feet. eek I did have an axle stand under there though, and I put a spare wheel under the car just in case. Probably not my smartest moment... hehe

mini turbo

303 posts

225 months

Monday 29th April 2013
quotequote all
Jack the car up take all the bolts out, wind 1 back in a little, lie on your back behind the car and kick the back of the wheel with the sole of ur foot.

clarkey540i

2,220 posts

205 months

Monday 29th April 2013
quotequote all
Plastic hammer usually does it. Put a bit of copper grease on the mating surface once you've got them off and it won't happen again.

eltax91

Original Poster:

10,799 posts

237 months

Monday 29th April 2013
quotequote all
sim16v said:
Or put all 5 back in, about half way, then drive 10 yards up and down the road.
Is this trick as handy with rear wheels as it is with the (steered) fronts. Doesn't seem there would be much lateral load to me. That said, it's worth a try. Will give it a bash.

mat777

10,714 posts

191 months

Monday 29th April 2013
quotequote all
clarkey540i said:
Plastic hammer usually does it. Put a bit of copper grease on the mating surface once you've got them off and it won't happen again.
Is this the point where we get another numpty coming in and saying that the bolts dont hold the wheel on, its hub friction due to clamping force blah blah and whatever we do dont grease the mating surface?

John D.

21,188 posts

240 months

Monday 29th April 2013
quotequote all
Emeye said:
I had this problem with my old mx5. I lay under the car and kicked the wheel off using my feet. eek I did have an axle stand under there though, and I put a spare wheel under the car just in case. Probably not my smartest moment... hehe
fk that.

SystemParanoia

14,343 posts

229 months

Monday 29th April 2013
quotequote all
P I Staker said:
Kick it.
this smile

works every time.... eventually!

Cemesis

771 posts

193 months

Monday 29th April 2013
quotequote all
Ideally you need to whack the tyre with the rubber mallet all the way around and keep doing it until the wheel pops off. Its better if you can rotate the wheel as you go but I suspect you'll have trouble doing that.

Keep at it though, the wheel will come off.

bearman68

4,942 posts

163 months

Monday 29th April 2013
quotequote all
BMW's bloody awful for this. Probably because no-one can afford to maintain them rofl

I had mine over the pit, and used a hydraulic jack from the side of the pit to the side of the wheel. 6 tonnes did it in the end. Took me a few hours though. (Didn't think of the driving about idea, so I'm going to try that next time).

y2blade

56,325 posts

246 months

Monday 29th April 2013
quotequote all
Kick it.

Deva Link

26,934 posts

276 months

Monday 29th April 2013
quotequote all
P I Staker said:
Get a hammer and a block of wood and knock them off.
I used a long bit of wood that I could hit from the other side of the car so I didn't have to be underneath it.

Deva Link

26,934 posts

276 months

Monday 29th April 2013
quotequote all
bearman68 said:
I had mine over the pit, and used a hydraulic jack from the side of the pit to the side of the wheel. 6 tonnes did it in the end. Took me a few hours though.
Hours? I'm amazed the wheel didn't fracture.

TTmonkey

20,911 posts

278 months

Monday 29th April 2013
quotequote all
I would go with loosening the bolts and going for a little drive. Your wheels wont fall off.


oh, and its not the job you want to do without the correct tools. Replacing rears is usually harder than fronts, and often you need a specialised tool to wind the rear hydraulics back in. Do you have that? Can be very tricky (but not impossible) without it.