Another, Dad I think .... MG ZS Rear Brake Calipers
Another, Dad I think .... MG ZS Rear Brake Calipers
Author
Discussion

MGJohn

Original Poster:

10,203 posts

214 months

Wednesday 1st May 2013
quotequote all
I do not often drive my wife's MG ZS so when my son got back after using it he remarked that he thinks the rear Brake Calipers were partially seizing on. He was right about that as a quick check a few days ago showed both rear wheels difficult to turn by hand. The offside being more difficult than the nearside wheel.

So ordered some new rear Brake pads ( £19 posted ~ ebay ) and these arrived yesterday. Today made a start and both rear Brake Calipers showed evidence of the pads being seized in their Carrier locations with irregular/tapered wear :~



Some evidence of light corrosion on the Pistons too which will need to be cleaned away before rewinding them :~



Carefully used old wire brush helped with an initial clean. I stress carefully to avoid damage to the seal :~



Although it was not excessive, I took the opportunity to remove the wear Lip from both sides of both discs with and angle grinder and a well worn Flappy Disc :~



For cleaning, I used a mist sprayer loaded with a mixture of Fairy Liquid and water ~ I guess about 20-1 mix which is fairly strong. An old long handled nylon washing up brush got that piston nicely cleaned ready to be rewound back into the Caliper using this tool :~



Here's the tool in action plus a close up view:~



Close up :~



Take it slowly using the rewind tool. Too hasty can ruck up the piston weather seal and even damage it.

I then cleaned the Brake Pads locations in the stainless steel location shims and added a smear of grease for the new Brake Pads to sit on. Even so, all the pad lugs needed to be lightly treated with the angle grinder to allow them to slide properly as the pad friction material wears down with brake use. Soon had it all back together and delighted with how well the rear brakes, including the hand brake now worked after a short drive to settle the new parts in. I used a smear of Copper Grease on key areas to minimise further corrosion of the metal. making sure to keep away from the nrake Discs and Brake pads.

As I worked, a Courier arrived with a parcel. It contained this :~



A remanufactured Front Right Brake Caliper to replace the seizing one on my Rover 45.

My younger son showed interest in the job and I took time to show him what these jobs entailed. Pleased about that as I do not want any family member to be a "I dunno where my bonnet release is" type of car user. That is not good news.

MGJohn

Original Poster:

10,203 posts

214 months

Wednesday 1st May 2013
quotequote all
So with all the tools out ready for the job ~ that always takes time setting up the tools for a job ~ thought three birds one stone and got the Rover 45 with its front right wheel clear supported by an axle stand.

This is what the original old Caliper looked like when I gave it some TLC recently ~ It did not improve things much and after a fast run, the front right alloy wheel was considerably warmer than the cool nearside one. Sure sign the Caliper was still partially sticking on :~



So with that nice shiny remanufactured Caliper all ready, soon had it on in place of the old one. Here it is being bled :~



Again using my younger son as helper, successfully bled caliper and all working well with no evidence of binding now.



Cleared all the tools away. Took it for a run and no doubt about it, that binding front brake depressed acceleration, speeds in all gears and no doubt affected fuel consumption too! Car is again a delight to drive ~ complete with bum warmers ... wink

cherad

37 posts

229 months

Wednesday 1st May 2013
quotequote all
Lovely write-up, MGJohn. Enjoyed this! smile

ChickenvanGuy

337 posts

202 months

Wednesday 1st May 2013
quotequote all
Always enjoy your threads, John - you make me (a mechanical dunderhead) feel I could have a go...


MGJohn

Original Poster:

10,203 posts

214 months

Wednesday 1st May 2013
quotequote all
ChickenvanGuy said:
.
Always enjoy your threads, John - you make me (a mechanical dunderhead) feel I could have a go...
.
One of the main reasons I take the time to post them up. It really isn't Rocket Science. I have no formal training in any mechanical areas and my skills are all self-taught from when I bought my first MGB close on half a century ago and a local garage did a very poor job on my still fairly new car. Once bitten twice wossname and despite not knowing a ring spanner from a socket drive, went out and bought a few starter tools and a BMC Factory Workshop Manual for the MGB.

First job I did was replace a front disc on the B ~ BTW, that new MGB Brake Disc cost a whole 28/= ( twenty eight shillings ... £1.40p ... wink ) and with each job, both my confidence and experience improved and enabled me to tackle more involved and complicated jobs on my cars.

My sons and I sat down recently and costed the work we've done on several family and friends' cars recently. In the average workshops all that work would easily exceed £3000 !! In top repair establishments rather more. All it cost us was about £250 for parts and our time. Working at a leisurely pace without a time or profit gun held to our heads, it is a pleasantly rewarding pastime in many ways ~ therapeutic in fact for me.. wink

Since those now faraway days with my first cars, must have saved a nice few quid and at the same time, safe in knowing the job not only well done, but actually done!

By the way, I sold that official BMC MGB Factory Workshop Manual recently ~ I know most of the stuff by heart now after twenty plus years of MGB and MGB GT ownership... got a good price for that too .. every little helps ... wink