Which way do the exhaust gaskets go?
Which way do the exhaust gaskets go?
Author
Discussion

chris1972

Original Poster:

3,597 posts

167 months

Monday 6th May 2013
quotequote all
Flat side to block? Also, do you use any compound to seal?

carsy

3,019 posts

195 months

Monday 6th May 2013
quotequote all
They will only go on one way. Although they fit the bolt holes either way round, they only fit the ports correctly one way. Have a closer look.

s p a c e m a n

12,114 posts

178 months

Monday 6th May 2013
quotequote all
Have no idea, but I have a pair here that I need to stick on mine so I am interested smile

chris1972

Original Poster:

3,597 posts

167 months

Monday 6th May 2013
quotequote all
carsy said:
They will only go on one way. Although they fit the bolt holes either way round, they only fit the ports correctly one way. Have a closer look.
Cheers. What about compound?

SILICONEKID350HP

14,997 posts

261 months

Monday 6th May 2013
quotequote all
chris1972 said:
Cheers. What about compound?
You can use this stuff ,most people use nothing ..

http://www.ebay.co.uk/itm/RTV-Silicone-Permatex-Ul...

EGB

1,774 posts

187 months

Monday 6th May 2013
quotequote all
SILICONEKID350HP said:
chris1972 said:
Cheers. What about compound?
You can use this stuff ,most people use nothing ..

http://www.ebay.co.uk/itm/RTV-Silicone-Permatex-Ul...
I did not use any and it's ok.

carsy

3,019 posts

195 months

Monday 6th May 2013
quotequote all
chris1972 said:
Cheers. What about compound?
Nothing.

chris1972

Original Poster:

3,597 posts

167 months

Monday 6th May 2013
quotequote all
Okay then, I may go commando to begin with and if I get a blow I'll squirt some gunge in there...

phazed

22,509 posts

234 months

Monday 6th May 2013
quotequote all
Use nothing then check the bolts after a while.

Checked my ARP bolts with Nordlock washers after 2K miles and all bolts needed tightening!

Discopotatoes

4,101 posts

251 months

Monday 6th May 2013
quotequote all
phazed said:
Use nothing then check the bolts after a while.

Checked my ARP bolts with Nordlock washers after 2K miles and all bolts needed tightening!
I have found the nord locks to be an expensive waste of time

s p a c e m a n

12,114 posts

178 months

Tuesday 7th May 2013
quotequote all
Has anyone got a link handy for the bolts so that I know I have the right ones, didnt think of getting some of them paperbag

chris1972

Original Poster:

3,597 posts

167 months

Tuesday 7th May 2013
quotequote all
I bought a set of stainless studs off Ebay for the RV8. Cost about £10 delivered.

carsy

3,019 posts

195 months

Tuesday 7th May 2013
quotequote all
Discopotatoes said:
I have found the nord locks to be an expensive waste of time
yes We could do with these Stage 8 locking tabs.

http://www.summitracing.com/search/brand/stage-8-l...

chris1972

Original Poster:

3,597 posts

167 months

Tuesday 7th May 2013
quotequote all
Now they look good and cheaper than the Nordlock stuff.

phazed

22,509 posts

234 months

Tuesday 7th May 2013
quotequote all
The logic of the Nordlocks makes little sense, they also wont bite into a stainless bolt?

So the point is?..

chris1972

Original Poster:

3,597 posts

167 months

Tuesday 7th May 2013
quotequote all
phazed said:
The logic of the Nordlocks makes little sense, they also wont bite into a stainless bolt?

So the point is?..
Is this a rhetorical question Peter?

phazed

22,509 posts

234 months

Tuesday 7th May 2013
quotequote all
chris1972 said:
phazed said:
The logic of the Nordlocks makes little sense, they also wont bite into a stainless bolt?

So the point is?..
Is this a rhetorical question Peter?
It dam well is, they're useless!

chris1972

Original Poster:

3,597 posts

167 months

Wednesday 8th May 2013
quotequote all
phazed said:
It dam well is, they're useless!
Very expensive too! Life would have a been a little easier if TVR had left two inches either side of each manifold.