Cape Cod Polishing Cloths - Advice
Cape Cod Polishing Cloths - Advice
Author
Discussion

JAGS

Original Poster:

1,092 posts

239 months

Monday 3rd June 2013
quotequote all
Hi,

Just ordered up a pack of these, intending to use them on a couple of things. Wanted to double check I wouldn’t be doing more harm than good before I set about polishing…

Item 1: Gold/Steel Rolex DJ on Oyster bracelet/Domed bezel

A few scratches on the gold parts, on the bezel and strap. The polished steel sides of the case also have a few scratches on them, which I wanted to get rid of.
Will be taping the brushed bits of steel off, so that the cloth does not get near them. Would this be ok to do? Just wanted to find out if using the cloth on the gold/steel polished areas will not discolour/damage the material at all?




Item 2: Mont Blanc Miesterstuck Diamond Le Grand Ballpoint Pen

Got a few scratches on the clear tip that has the floating diamond in it. Wanted to get it back to clear and ‘shiny’. The pen also has a few hairline scuffs from regular use. Would using the cloth on both areas of the pen have any potentially catastrophic results? Will cover/tape off any potentially sensitive areas (clip and other plated metalwork).


Thanks in advance.

JAGS

Original Poster:

1,092 posts

239 months

Tuesday 4th June 2013
quotequote all
Bump - anyone?

bobbybee

889 posts

185 months

Tuesday 4th June 2013
quotequote all
if you tape off the brushed parts and are really careful, you shouldn't have much of an issue. Even if you make some areas shiny, you can get a fibreglass refinishing pen, to put the brush effect back.

As to whether you can use a Cape-Cod on gold or other softer materials, their literature does not mention gold, so I would steer clear. As it is a very soft metal you'll only wear it away. Vut that's just IMHO

CardShark

4,264 posts

210 months

Tuesday 4th June 2013
quotequote all
Never tried it myself but, as above, taping off any brushed areas seems to be the way to go as well as using a fibreglass pen to refresh brushed areas. I have used CC cloths on polished steel, they work well IMO.

C&P'd from the Cape Cod site "FOIL POUCH CAPE COD® METAL POLISHING CLOTHS
Two 4" X 6" Cape Cod® Metal Polishing Cloths: moist polishing cloths that clean, polish, and protect any type of metal. Re-closable foil pouch." and clicky here suggests that the cloths will be fine for gold.

JAGS

Original Poster:

1,092 posts

239 months

Thursday 6th June 2013
quotequote all
Thanks for the advice all.

Decided against using the cloth on my MB Pen, but did go to work on my Tissot Visodate first and then onto the Rolex...

Forgot to take 'before' pics of the Tissot, but it turned out looking like brand new after 15 minutes of careful polishing:






Rolex before:




Rolex after:






Although this was only about 15 odd minutes of polishing on the Rolex, there is a marked improvement. most of the bigger scuffs have gone, but there are a few hairline scratches left, which I will re-visit in a few days. taped up the brushed bits accordingly and they were well protected. removed the tape and gave the watch a final buffing. I am pleased with the results. The polished gold bits were looking almost brushed on the strap. They look much better now.


£4.60 very well spent on a couple of polishing cloths!

CardShark

4,264 posts

210 months

Thursday 6th June 2013
quotequote all
thumbup

jonny70

1,280 posts

189 months

Thursday 6th June 2013
quotequote all
JAGS said:
Thanks for the advice all.

Although this was only about 15 odd minutes of polishing on the Rolex, there is a marked improvement. most of the bigger scuffs have gone, but there are a few hairline scratches left, which I will re-visit in a few days. taped up the brushed bits accordingly and they were well protected. removed the tape and gave the watch a final buffing. I am pleased with the results. The polished gold bits were looking almost brushed on the strap. They look much better now.


£4.60 very well spent on a couple of polishing cloths!
I have a few scratches on the side of Rolex ceramic sub (the polised part not brushed) will these clothes remove the scratches?


JAGS

Original Poster:

1,092 posts

239 months

Thursday 6th June 2013
quotequote all
I don't see why not.

Just take your time when using the cloth. Even pressure (moderate, not heavy) and going one way only should see the scratches reduce after a couple of minutes polishing. Polish for a few mins, buff off and see results. repeat until happy.

Obviously you are taking a bit of material off when polishing, so don't over do it!

Please do post up before/after pics if you do it.

jonny70

1,280 posts

189 months

Thursday 13th June 2013
quotequote all
JAGS said:
I don't see why not.

Just take your time when using the cloth. Even pressure (moderate, not heavy) and going one way only should see the scratches reduce after a couple of minutes polishing. Polish for a few mins, buff off and see results. repeat until happy.

Obviously you are taking a bit of material off when polishing, so don't over do it!

Please do post up before/after pics if you do it.
this is what i need?

http://www.ebay.co.uk/itm/CAPE-COD-Fine-Metal-Poli...

for the polished sides of my ceramic sub?

bobbybee

889 posts

185 months

Friday 14th June 2013
quotequote all
jonny70 said:
this is what i need?

http://www.ebay.co.uk/itm/CAPE-COD-Fine-Metal-Poli...

for the polished sides of my ceramic sub?
Yes, I use the same on the polished sections of my Sub-Date