Titan Black Rolex
Discussion
I was sent a link to the Titan Black website by a mate the other day. Do any of you watch aficionado's have good or bad thoughts about them? Do you think that they are likely to gain/hold value well? All seem to be limited production runs, and there are one or two in particular that I like the look of....
http://www.titanblack.co.uk/collection/rolex/dayto...
http://www.titanblack.co.uk/collection/rolex/dayto...
http://www.titanblack.co.uk/collection/rolex/dayto...
http://www.titanblack.co.uk/collection/rolex/dayto...
As long as people have money and want black Rolexes these "exclusive", "limited" and "individual" versions will be produced. When you come to sell it you'll easily find a buyer but you may find it difficult to get what you paid for it or even much of a premium over a normal stainless steel model.
CommanderJameson said:
I would imagine that their 2nd hand values will drop like a rock, because (I think) Rolex will not service these watches.
This - buy one second hand though if you can - i did and believe i got a great deal - discussed in this thread - http://www.pistonheads.com/xforums/topic.asp?h=0&a...To be honest, it's the same as anything. If you think it's worth the money and you have the money then why not. It doesn't matter what people on the internet say.
I personally like that Daytona, but I don't think it's worth what the sellers want, so I'll stick with my SS Daytona. If I really want PVD and a new face (for the watch, not me), I can have those done for a lot less than that.
I personally like that Daytona, but I don't think it's worth what the sellers want, so I'll stick with my SS Daytona. If I really want PVD and a new face (for the watch, not me), I can have those done for a lot less than that.
Hi,
Yer some can be a pain if they have a tight tolerance fit or not familiar with the case or movement etc.
Obvs Rolex can be stressful sometimes Panerais usually ok just depends the odd model can be stressful occasionally.
You also have to be sure replacement parts like gaskets that can easily get nipped or not spotted can be sourced, and obvs with chrono pushers and small parts that might get misplaced or lost at the coaters.
Bracelets aren't that easy to coat as the coating is done by 'line of sight' very different to electroplating, most PVD coaters rely on PA-CVD which is Plasma Assisted Chemical Vapour Deposition to coat 3D objects, so the odd parts might need recoating, which usually means all the parts will be sent back here the uncoated part detected and the coating removed and posted back for recoating.
Another thing Ar coated sapphires the coatings are fragile can easily be marked if not handled or removed carefully, even a tiny bit of grit on the polishing cloth will micro scratch an Ar!
Yer some can be a pain if they have a tight tolerance fit or not familiar with the case or movement etc.
Obvs Rolex can be stressful sometimes Panerais usually ok just depends the odd model can be stressful occasionally.
You also have to be sure replacement parts like gaskets that can easily get nipped or not spotted can be sourced, and obvs with chrono pushers and small parts that might get misplaced or lost at the coaters.
Bracelets aren't that easy to coat as the coating is done by 'line of sight' very different to electroplating, most PVD coaters rely on PA-CVD which is Plasma Assisted Chemical Vapour Deposition to coat 3D objects, so the odd parts might need recoating, which usually means all the parts will be sent back here the uncoated part detected and the coating removed and posted back for recoating.
Another thing Ar coated sapphires the coatings are fragile can easily be marked if not handled or removed carefully, even a tiny bit of grit on the polishing cloth will micro scratch an Ar!
Edited by bry1975 on Sunday 23 June 12:40
Gassing Station | Watches | Top of Page | What's New | My Stuff



