Error code 19

[peteA]

What's this then? On the way home today enjoying the sunshine the dash pops up with error code 19 petrol sensor? When pulling away there was a lul and then the car shot forward...not unlike a sticking throttle I guess? Other than that the car drove fine...

Is it a faulty lambda sensor?

Sure it's been done before but for future convenience has anyone got a list of error codes and what they are?

Thanks in advance.

[shep1001]

It won't be the lambda. Send me your email and I will send the list later. Can't remember what it is though.


Oil_P_Under_Min =0x01 =1
Oil_P_Over_Max =0x02 =2
Oil_P_Lamp_On =0x03 =3
EFI_MIL_Lamp_On =0x04 =4
Water_T_Over_Max =0x05 =5
Oil_T_Over_Max =0x06 =6
Battery_Over_Max =0x07 =7
Alternator_Lamp_On =0x08 =8
Inertia_Lamp_On =0x09 =9
Battery_Under_Min =0x0a =10
Fuel_L_Under_Min =0x0b =11
Air_T_Under_Min =0x0c =12
Brake_Fluid_Lamp_On =0x0d =13
RH_Door_Lamp_On =0x0e =14
LH_Door_Lamp_On =0x0f =15
Light left on =0x10 =16
No seat belt =0x11 =17
Gear_T_Over_Max =0x12 =18
Diff_T_Over_Max =0x13 =19
Low_Fuel_Pressure =0x14 =20
High_Fuel_Pressure =0x15 =21

Fault Codes:

Water sensor =0x80 =128
Oil temp sensor =0x81 =129
Oil pressure sensor =0x82 =130
Fuel level sensor =0x83 =131
Air temp sensor =0x84 =132
Speedo zero =0x85 =133
Tacho zero =0x86 =134
Heater controls =0x87 =135
Heater flap zero =0x88 =136
Aircon Fault =0x89 =137
Gear_T_Sensor_Fault =0x8a =138
Diff_T_Sensor_Fault =0x8b =139
Fuel_P_Sensor_Fault =0x8c =140
Brake Fluid Sw.fault =0x8d =141

Power supply control =0x90 =144
Display FRAM failed =0x91 =145
Display FRAM corrupt =0x92 =146
Stepper FRAM failed =0x93 =147
Stepper FRAM corrupt =0x94 =148
Time clock failed =0x95 =149
Time clock corrupt =0x96 =150
Inter uP comms failed =0x97 =151
System initiation =0x98 =152
software invalid =0x99 =153
display switches fault =0x9a =154

Edited by shep1001 on Wednesday 10th July 00:32

[peteA]

Thanks Shep - tried to email you last night but my iphone wasn't playing ball?

Cheers for the codes - so are the top ones error codes and the bottom ones fault codes - assume they are different?

Looking at it my error code 19 it a diff temp issue....if you had asked me before this happened if my car had a diff temp sensor I would have said no! I know it was hot yesterday but not that hot! What are you supposed to do when this happens....pull over and wait a few hours?

I fired the car up this morning and its gone (as you would expect I guess).

Thanks again

[jrb43]

peteA said:

What are you supposed to do when this happens....I fired the car up this morning and it's gone (as you would expect I guess).

Very often the correct response - well done you've fixed it

An error code means that the parameter being measured is out of accepted range (driver's door open, water temperature too hot etc.) A fault code means the sensor is returning inappropriate data (usually, but not always, meaning there's a problem with the sensor/its wiring).