DB9 Big End Bearings - Help needed
DB9 Big End Bearings - Help needed
Author
Discussion

MaverickV12

Original Poster:

1,086 posts

169 months

Friday 12th July 2013
quotequote all
Hello people,

I have stripped down the sump off of the old V12, and I want to change the bearings. I took the first one off and took a photo .....



I asked Aston to send a new set of big end bearings, but they said that they needed the Bearing number (which I gave them), then they asked for the number on the Conrod, I delved into the engine and found the number that is printed on the conrod (not stamped).

Gave Aston this number, then they said, they need the number on the crown of the Piston, I guess this means that I have to take the spark plug out etc,

It would appear that I have asked Aston for the secret to eternal youth and they don't want to give it over, indeed the Franchise Dealer that is helping me has said that it appears that Aston dont want to be very helpful (thats from a Franchise dealer)

Does anyone know where I can get a set of bearings for a DB9 ......... smile

Jon39

15,022 posts

174 months

Friday 12th July 2013
quotequote all

MaverickV12 said:
Does anyone know where I can get a set of bearings for a DB9 ?
Once again you have my admiration, for doing heart surgery on your car.
If my memory is correct, I think last time you had the top end in pieces, and then immediately drove to the Arctic. A man who trusts his mechanical ability.

Might B & R be the answer to your question?



Edited by Jon39 on Friday 12th July 15:37

DB9VolanteDriver

2,661 posts

207 months

Friday 12th July 2013
quotequote all
Just look at you! You are one very determined and brave dude, stripping the bottom end off your engine. Please keep posting your progress. It mat not be about JLC, red trousers, George, being left behind, or who the biggest 'tosser' is, but it is very interesting to some of us. Good job!

PiloteAM

868 posts

241 months

Friday 12th July 2013
quotequote all
Hm, odd, you would think Aston would be a bit more helpful - how many times can they have changed the bearing design over that timeperiod?

Maybe try someone like Aston Martin Bits? Never used them myself, but I've heard that the guy is very knowledgeable and helpful over the phone.

If not, BR have done a number of rebuilds - so I guess they would know the easiest way to find the number Aston need. It can't involve much more dismantling than you've already done!

Russwhitehouse

962 posts

162 months

Friday 12th July 2013
quotequote all
Jon39 said:
Once again you have my admiration, for doing heart surgery on your car.
If my memory is correct, I think last time you had the top end in pieces, and then immediately drove to the Arctic. A man who trusts his mechanical ability.

Might B & R be the answer to your question?


Drove to the Arctic!! Holy moly!! I'd like to hear more of that story! Very best of luck with the search and the rebuild. You are clearly a very rare type of owner.
Edited by Jon39 on Friday 12th July 15:37

Ikebaddog

318 posts

166 months

Friday 12th July 2013
quotequote all
DB9VolanteDriver said:
Just look at you! You are one very determined and brave dude, stripping the bottom end off your engine. Please keep posting your progress. It mat not be about JLC, red trousers, George, being left behind, or who the biggest 'tosser' is, but it is very interesting to some of us. Good job!
+1, top man, most owners on here are scared to open the bonnet without paying AM to do it.

avinalarf

6,438 posts

173 months

Friday 12th July 2013
quotequote all
Ikebaddog said:
+1, top man, most owners on here are scared to open the bonnet without paying AM to do it.
Open the bonnet ? yikes

Russwhitehouse

962 posts

162 months

Friday 12th July 2013
quotequote all
avinalarf said:
Open the bonnet ? yikes
Which bit is the bonnet? Oh I know, it's connected to the wheels or something. Do red cars go faster?

avinalarf

6,438 posts

173 months

Friday 12th July 2013
quotequote all
Russwhitehouse said:
avinalarf said:
Open the bonnet ? yikes
Which bit is the bonnet? Oh I know, it's connected to the wheels or something. Do red cars go faster?
Not sure Russ ,I think it's the sticking out bit at the front.
Better ask Neilc123 he seems to know a lot about Astons.
I really do not understand the problem or the fuss I have underlings that I pay to get their hands dirty.

P.S. Sincere apologies to Maverick for going off topic and for whom I have great admiration for having the skill and balls to have a go.


Edited by avinalarf on Friday 12th July 19:39


Edited by avinalarf on Friday 12th July 19:40

crypto

240 posts

272 months

Sunday 14th July 2013
quotequote all
MaverickV12 said:
Hello people,
Does anyone know where I can get a set of bearings for a DB9 ......... smile
You are really doing heart surgery wink In the AMOC club news are always a number of companies doing engine mods/rebuilds. If you don't have one at hand, try contacting one of these :
www.enginology.co.uk
www.oselli.com
info@headshop-uk.com +44(0)1925 851166/77

I'm not sure if you can order a "set". Maybe tolerances are nowadays so tight that they are really all the same. I would measure each of them, because in my earlier days crank journals had certain tolerances. To make sure you have the right oil pressure, shells must have been selected accordingly.

Because I don't know B&R is there a web-link ?

3200gt

2,727 posts

255 months

Sunday 14th July 2013
quotequote all
Only gives one part number in the parts manual "02-85781"

MaverickV12

Original Poster:

1,086 posts

169 months

Sunday 14th July 2013
quotequote all
......thanks guys,

The conrod has, "Ford", stamped all over it, so basically its just a 500cc Ford piston, I'll get on to it Monday and see if I can track some down.

Looking at the bearings that I have taken out, they look brilliant, I have taken 2 out and looked at 3 others (5 in total) and they look like they really don't need replacing, unless of course there is something I'm missing, or don't understand.

Cleaned the sump up nicely .....



smile

Jon39

15,022 posts

174 months

Sunday 14th July 2013
quotequote all

MaverickV12 said:
Looking at the bearings that I have taken out, they look brilliant, I have taken 2 out and looked at 3 others (5 in total) and they look like they really don't need replacing.
When I first read your post, the thought did occur to me, what made you decide to remove the sump and main bearings? Was there a knocking noise?

I have never owned a car (even after 200,000 miles) where the main bearing shells have worn out.

What is that mechanics old saying? "If it aint broke .........." smile



GTDB7

958 posts

199 months

Sunday 14th July 2013
quotequote all
Maverick has a ticking noise that is coming from the rear bottom end somewhere.

I wonder if it could be an output shaft bearing?

Even just a slight flat spot on one of the racers could produce a tick I guess.

As the engine is stripped to this level it might be worth checking.


MaverickV12

Original Poster:

1,086 posts

169 months

Monday 15th July 2013
quotequote all
Hi guys, do you mean this ........



Can you tell me what I'm looking for?

Also, I just had an email from FPS, not quite sure what that stands for, but they supply bearing etc. They said this ......




Good Afternoon,

I have investigated your query with our main engine parts suppliers, and
unfortunately they are unable to provide such an item for your DB9 as they
do not catalogue any Aston Martin parts and were unable to locate parts
using the details you sent across.

It may well be that the parts are marked Ford but are specially made for
Aston Martin, and that due to the high performance nature of the car and
wanting to ensure it still performs once parts are replaced, this is perhaps
the reason why Aston aren't prepared to divulge part number details,
according to the technical advisor I spoke to at our main supplier of such
parts.

I'm sorry I couldn't be of more help.

Many thanks




TBH, I did not have much time this morning to look for this stuff (work always gets in the way) and this was the only people that I had contacted, does anyone have any phone numbers they can post that I can call some suppliers of bearing etc.

Turning to the existing bearings, what am I looking for? because the micrometer has a flat surface on the measurement thingy and the bearing is curved, then I can only measure relatively accurately....... smile

MaverickV12

Original Poster:

1,086 posts

169 months

Monday 15th July 2013
quotequote all
Can the oil pump be taken out from below? smile Or do you have to take off the front of the engine? frown

john ryan

542 posts

163 months

Tuesday 16th July 2013
quotequote all

Turning to the existing bearings, what am I looking for? because the micrometer has a flat surface on the measurement thingy and the bearing is curved, then I can only measure relatively accurately.......

Use a ball bearing - mike the diameter, and then put in between the mike anvil and the concave side of the bearing shell. A subtraction will give shell thickness.

MaverickV12

Original Poster:

1,086 posts

169 months

Wednesday 17th July 2013
quotequote all
I looked at the bearings again and started to measure them.....

This photo shows the inside of the bearings .......



Whilst they show black marks, they are as smooth as a babies bum ......

Turned over .......



..... they look as, "silver", as the day they came out of the factory (ish).

I measured the bearings, I assume you mean like this ......



I took three measurements across the bearings and they were

18.365mm
18.360mm
18.345mm

and

18.330mm
18.365mm
18.365mm

I am assuming that this is about what we would expect? Is it? I haven't a clue ........ confused

I have emailed Bamford Rose and asked Mike for help in trying to locate some bearings or even if they could supply some, hopefully he/they can point me in a good direction smile

V12Vantage

477 posts

170 months

Wednesday 17th July 2013
quotequote all
It's the thickness of the bearing you should be checking not the width. You can do this with a ball bearing between the shell face and the micrometer.

You probably also need to check the main bearings for wear / damage at the same time.

Jon39

15,022 posts

174 months

Wednesday 17th July 2013
quotequote all

MaverickV12 said:
I measured the bearings, I assume you mean like this ......



I took three measurements across the bearings and they were

18.365mm
18.360mm
18.345mm

I am assuming that this is about what we would expect? Is it? I haven't a clue ........ confused
As I have previously mentioned, you certainly have my admiration Maverick, for attempting the engine work that you do.

However, I think I might have spotted a windup. Your comment about measuring the width of the bearings, is akin to measuring the width of a tyre, to check the tread wear.

Yes very good, you caught us all. smile

Oh by the way. Did you mark each bearing shell, so that they can all be returned to their original positions?