HELP with alloy fitments!! NEWB
HELP with alloy fitments!! NEWB
Author
Discussion

ABaruwal

Original Poster:

14 posts

159 months

Saturday 10th August 2013
quotequote all
Hello,

I'm completely new at buying/fitting car parts and have very little knowledge.
I recently bought a golf mk4 and am about to buy a set of new alloys with new fitted tyres.

Info of tyres and alloys are as followed:
5 Stud fitment, 5x100/5x110 PCD,
35mm offset
73.1mm Centre Bore
Tyres are 225/40R18

So i'm wondering what i need to consider before buying?

Correct me if i'm wrong but as far as i know 5x100 pcd is correct fitment for my car, as the bore hole is too big i will need spigot rings.

So the questions are:

Will the standard studs fit the new alloys or will i need to buy new set of studs?
Are the tyres too big or will they fit ?
Also, is it wise to have all four tyres the same size or should the front two be slightly smaller? (Sorry if this is bit of a dumb q)
Does the alloy's offset look right for the golf mk4?

I would also appreciate any other thing i need to consider or any suggestions in general.

Thanks in advance

McWigglebum4th

32,414 posts

235 months

Saturday 10th August 2013
quotequote all
No idea but it will look silly on huge alloys and they will cause untold problems while making your car slower and handle worse

jet_noise

6,111 posts

213 months

Saturday 10th August 2013
quotequote all
Dear A,

by how much will your insurance increase when you tell them the car's been modified?

regards,
Jet

ABaruwal

Original Poster:

14 posts

159 months

Saturday 10th August 2013
quotequote all
McWigglebum4th said:
No idea but it will look silly on huge alloys and they will cause untold problems while making your car slower and handle worse
But the outer diameter of the wheels will be the same as the old standard steel wheels with tyres

tinkertaylor

566 posts

173 months

Saturday 10th August 2013
quotequote all
I'm guessing this is going to be some ridiculous dub car slammed to the ground hehe

Chongwong

1,045 posts

178 months

Saturday 10th August 2013
quotequote all
Does the entire wheel fit beneath the wheel-arch, as if you can see Tyre or alloy from above it is illegal (i think, but you'd be best researching that)

ABaruwal

Original Poster:

14 posts

159 months

Saturday 10th August 2013
quotequote all
jet_noise said:
Dear A,

by how much will your insurance increase when you tell them the car's been modified?

regards,
Jet
I need to change the tyres anyway so i thought it'd be wise to change both alloys and tyres together as it was actually cheaper. I found a good deal with both new alloys and fitted tyres

McWigglebum4th

32,414 posts

235 months

Saturday 10th August 2013
quotequote all
ABaruwal said:
McWigglebum4th said:
No idea but it will look silly on huge alloys and they will cause untold problems while making your car slower and handle worse
But the outer diameter of the wheels will be the same as the old standard steel wheels with tyres
But they are cheap alloys so will weigh about as much as an elephant


ABaruwal

Original Poster:

14 posts

159 months

Saturday 10th August 2013
quotequote all
tinkertaylor said:
I'm guessing this is going to be some ridiculous dub car slammed to the ground hehe
Haha not really.. I wont be touching the suspension at all. The only reason im changing is because the current wheels are 14 inch and looks like they came of a toy car, also they're very old and have age related marks and kerbing.

ABaruwal

Original Poster:

14 posts

159 months

Saturday 10th August 2013
quotequote all
McWigglebum4th said:
But they are cheap alloys so will weigh about as much as an elephant
As long as they're lighter than the current steel wheels i'll b happy :-)

McWigglebum4th

32,414 posts

235 months

Saturday 10th August 2013
quotequote all
ABaruwal said:
McWigglebum4th said:
But they are cheap alloys so will weigh about as much as an elephant
As long as they're lighter than the current steel wheels i'll b happy :-)
You're going to get a nice surprise

ABaruwal

Original Poster:

14 posts

159 months

Saturday 10th August 2013
quotequote all
Chongwong said:
Does the entire wheel fit beneath the wheel-arch, as if you can see Tyre or alloy from above it is illegal (i think, but you'd be best researching that)
Thank you for the only helpful answer. The upgrade alloys will be just few mm bigger than the current wheels in diameter so there're will be plenty of space between the arch and the wheels.

Ps. I'm not lowering the car or altering the suspension

ABaruwal

Original Poster:

14 posts

159 months

Saturday 10th August 2013
quotequote all
McWigglebum4th said:
You're going to get a nice surprise
Oh dear, you're scaring me :-(

mikecassie

676 posts

190 months

Saturday 10th August 2013
quotequote all
ABaruwal said:
Chongwong said:
Does the entire wheel fit beneath the wheel-arch, as if you can see Tyre or alloy from above it is illegal (i think, but you'd be best researching that)
Thank you for the only helpful answer. The upgrade alloys will be just few mm bigger than the current wheels in diameter so there're will be plenty of space between the arch and the wheels.

Ps. I'm not lowering the car or altering the suspension
I think Chongwong is meaning if you are looking directly down from above the wheelarch, do you see any tyre or alloy? The width/offset being different might well render the fitment illegal. Or if not that then it might well rub on the arches as you go over our high quality highways.....

TheEnd

15,370 posts

219 months

Saturday 10th August 2013
quotequote all
ABaruwal said:
McWigglebum4th said:
You're going to get a nice surprise
Oh dear, you're scaring me :-(
They might be heavier, but driving to and from work and popping out to the shops isn't going to make a difference.

Spiggot rings- yep, needed.
Studs - should be fine, usually only need changing if spacers are added.

Keep all tyres the same size, it makes things easier, and shouldn't cause any traction control or ABS problems

Not sure about the offset, have a look on ebay at people selling similar sized wheels and you'll get a feel of what offsets are needed.

HustleRussell

26,715 posts

191 months

Saturday 10th August 2013
quotequote all
18" wheels with cheap tyres on a mk4 will just make it ride and handle terribly. The alloys will be much heavier than the steels.

ABaruwal

Original Poster:

14 posts

159 months

Saturday 10th August 2013
quotequote all
TheEnd said:
They might be heavier, but driving to and from work and popping out to the shops isn't going to make a difference.

Spiggot rings- yep, needed.
Studs - should be fine, usually only need changing if spacers are added.

Keep all tyres the same size, it makes things easier, and shouldn't cause any traction control or ABS problems

Not sure about the offset, have a look on ebay at people selling similar sized wheels and you'll get a feel of what offsets are needed.
Thank you so much.. Just what i needed

wildoliver

9,325 posts

247 months

Saturday 10th August 2013
quotequote all
Why not just by some standard Vw alloys that fit and suit the car?

Or is that too logical?

PaulGT3

377 posts

203 months

Chongwong

1,045 posts

178 months

Saturday 10th August 2013
quotequote all
mikecassie said:
I think Chongwong is meaning if you are looking directly down from above the wheelarch, do you see any tyre or alloy? The width/offset being different might well render the fitment illegal. Or if not that then it might well rub on the arches as you go over our high quality highways.....
This: I was still feeling last nights beverages,so my explanation was crappy biggrin
I'm not a big fan of Blingy wheels, but each to there own. If you like it and it's legal, do it. smile