CV joint grinding noise????
CV joint grinding noise????
Author
Discussion

speed_monkey

Original Poster:

3,503 posts

220 months

Monday 12th August 2013
quotequote all
Hi All,

Recently I haveheard quite an audible grinding noise at low speed from my Polos front end.

Its like a loud rubbing noise, I have always been under the impression that CV joints make a "clicking noise" but is it possible for them to make a grinding noise, worse when any amount of angle is on the steering wheel.

After changing my discs and pads successfully I now feel like a mechanical god of automotives.... So, is replacing the CV joints something DIYable?

speed_monkey

Original Poster:

3,503 posts

220 months

Monday 12th August 2013
quotequote all
Ok... before I click to pay for new joints to be delivered, can someone tell me if this is a job that I could do myself?

Looking online it would appear it is, however if someone from the PH masses could say yay or nay??

cheesesliceking

1,577 posts

271 months

Monday 12th August 2013
quotequote all
what car is it?

Prof Prolapse

16,163 posts

221 months

Monday 12th August 2013
quotequote all
Have you checked the wheel bearings first?

speed_monkey

Original Poster:

3,503 posts

220 months

Monday 12th August 2013
quotequote all
Its a 2000 plate Polo GTi

Oh.... wheel bearings are a good shout, jack it up and feel for play in the wheel? Is that sufficient?

tigger1

8,486 posts

252 months

Monday 12th August 2013
quotequote all
Had this on an old clio. A seal on the joint had gone, pissing grease everywhere - so joint was dry. Could be similar.

boyse7en

8,248 posts

196 months

Monday 12th August 2013
quotequote all
That will tell you if wheel bearings are knackered, but they may or may not be the source of your noise.

I had a Citroen that made a grinding noise on left-hand turns. Replaced wheel bearings (both sides), cv joint, driveshaft centre bearing, then the whole o/s driveshaft. Still made the noise. I just lived with until, about 6 months later, I realised the noise had stopped of its own accord.

To replace your wheel bearings you'll need access to a hydraulic press to remove old one and fit new one, once you've got the hub carrier off the car (for which you'll need a balljoint splitter of some type)

speed_monkey

Original Poster:

3,503 posts

220 months

Monday 12th August 2013
quotequote all
tigger1 said:
Had this on an old clio. A seal on the joint had gone, pissing grease everywhere - so joint was dry. Could be similar.
Would that mean a unit replacement or just the boot? Mind you, you need to take the unit off to replace the boot so a whole unit change would probably be best.

Prof Prolapse

16,163 posts

221 months

Monday 12th August 2013
quotequote all
boyse7en said:
To replace your wheel bearings you'll need access to a hydraulic press to remove old one and fit new one, once you've got the hub carrier off the car (for which you'll need a balljoint splitter of some type)
I'd have a bash with a hammer and a blowtorch personally.

Only VW I've ever done this on was an early Golf GTi, but for seperating the joints you can use this:

http://www.machinemart.co.uk/shop/product/details/...

£6 and lasts a lifetime.




Prof Prolapse

16,163 posts

221 months

Monday 12th August 2013
quotequote all
OP,

Check the wheel bearings. There's a million guides as to how. Also inspect the CV boot.

Rotating the wheel whilst your under it should give you some idea as to where the problem lies. If you can't replicate the sound on the jack it would point to the wheel bearing.

If you're doing it on the cheap and can't be sure of which it is replace the cheapest part first.

speed_monkey

Original Poster:

3,503 posts

220 months

Monday 12th August 2013
quotequote all
Prof Prolapse said:
OP,

Check the wheel bearings. There's a million guides as to how. Also inspect the CV boot.

Rotating the wheel whilst your under it should give you some idea as to where the problem lies. If you can't replicate the sound on the jack it would point to the wheel bearing.

If you're doing it on the cheap and can't be sure of which it is replace the cheapest part first.
Not doing on the cheap per se, just after doing my brakes last weekend has given me the "bug" so anything that I can do at home I will have a crack at pulling apart myself....

I will wait till I get home tonight and check wheel bearings, unfortunately I do not have access to a hydraulic press so may be out of my hands. How much on average would I expect to pay for wheel bearings to be replaced?

Prof Prolapse

16,163 posts

221 months

Monday 12th August 2013
quotequote all
About an hours labour plus about £30 for the bearing a side. Depends on charge per hour and what bearings they use.

It's a piece of piss job so take it to a monkey garage and supply the part yourself to keep costs down. I would get a reasonable quality bearing to replace it with personally.

(If it's the bearing!)



speed_monkey

Original Poster:

3,503 posts

220 months

Monday 12th August 2013
quotequote all
Prof Prolapse said:
About an hours labour plus about £30 for the bearing a side. Depends on charge per hour and what bearings they use.

It's a piece of piss job so take it to a monkey garage and supply the part yourself to keep costs down. I would get a reasonable quality bearing to replace it with personally.
Ah excellent, not too much of a sting then!

I will get a reasonably priced bearing as I am going to get rid of this liability of a car as soon as I clear the intermittent ABS fault and the intermittent "check engine" light..... bloody thing!!!

Edited by speed_monkey on Monday 12th August 13:20

Prof Prolapse

16,163 posts

221 months

Monday 12th August 2013
quotequote all
Compromise parts are usually best!

I normally try and find out who supplied the manufacturer then use their parts. Saves a fortune and you know its OEM spec!

XG332

3,927 posts

219 months

Monday 12th August 2013
quotequote all
Wheel bearings. Jack up the wheel and holding the tyre at 12 - 6 and 9 - 3 try to move the wheel in and out.
Do this cold and after a journey when warm.
If you feel movement check its not play in the steering rack, track rod end or lower ball joints.

CV joint. Have a quick look at the boot and look for any cv grease that has been thrown out when the shaft turns.
Then at walking pace drive in a figure of 8 on full lock. Listen out for any ticking, knocking, grinding or similar.

Hope this helps.

Super Slo Mo

5,374 posts

229 months

Monday 12th August 2013
quotequote all
You're assuming it is the bearing of course, however, it does sound like it. You ought to be able to grab the top of the wheel and pull/push it back and forth to find out, or failing that, jack it up. If there's any kind of clicking movement it's the bearings. CV joints tend to knock when they go.

Both are a job that requires around 200 lb/ft of torque to undo and re-tighten the nut on the end of the driveshaft. You'll need an assistant to stand on the brake pedal while you do this, personally I'd suggest going to a garage, as another poster has suggested, it's not that expensive of a job.

As a general rule of thumb, front wheel bearings make more noise when you turn away from the side that's failing (so turn left for a RH bearing, and vice versa), rear wheel bearings are not so obvious, but will still get louder as you turn.

ETA: This noise didn't start shortly after you replaced the disks/pads by any chance?

speed_monkey

Original Poster:

3,503 posts

220 months

Monday 12th August 2013
quotequote all
Prof Prolapse said:
Compromise parts are usually best!

I normally try and find out who supplied the manufacturer then use their parts. Saves a fortune and you know its OEM spec!
Just found that Euro car parts have them in stock for £28.00 is that a reasonable price?

XG332

3,927 posts

219 months

Monday 12th August 2013
quotequote all
Changing the bearings and joints is pretty simple, as others have said.
Bearing is as simple as press out and press in.

Cv joint is simply knock the old joint off the shaft and push the new one on.
It isn't usually that simple as over time corrosion an a corroded spring clip will make it a right pain.

speed_monkey

Original Poster:

3,503 posts

220 months

Monday 12th August 2013
quotequote all
speed_monkey said:
Just found that Euro car parts have them in stock for £28.00 is that a reasonable price?
Scratch that... £21.00 from GSF

speed_monkey

Original Poster:

3,503 posts

220 months

Monday 12th August 2013
quotequote all
XG332 said:
Changing the bearings and joints is pretty simple, as others have said.
Bearing is as simple as press out and press in.

Cv joint is simply knock the old joint off the shaft and push the new one on.
It isn't usually that simple as over time corrosion an a corroded spring clip will make it a right pain.
I just don't have the tools available to do the bearings (hydraulic press), looking at online guides the CV joints dont look too difficult