Need Help! Did the garage fook my driveshaft?
Need Help! Did the garage fook my driveshaft?
Author
Discussion

Idontdrinkrsmoke

Original Poster:

126 posts

167 months

Saturday 17th August 2013
quotequote all
Hi All

My car went in to a well known tyre/brakes/suspension/exhaust place for a rear wheel bearing yesterday and after 6 hours the garage told me my driveshaft was knackered and no point doing the bearing until I get driveshaft fixed.

In June my car was serviced by a specialist and in the report there is a big green tick at 'driveshaft'.

So, is it possible to damage a driveshaft while attempting to replace a wheel bearing? RWD car.

Any thoughts/opinions appreciated.


Willy Nilly

12,511 posts

198 months

Saturday 17th August 2013
quotequote all
Every time I have been in one of those places they try to sell me something else. Last time it was brakes, the car passed it's MOT with no advisories a couple of months later. The time before that it was shock absorbers, that was about 4 years ago.

Idontdrinkrsmoke

Original Poster:

126 posts

167 months

Saturday 17th August 2013
quotequote all
Willy Nilly said:
Every time I have been in one of those places they try to sell me something else. Last time it was brakes, the car passed it's MOT with no advisories a couple of months later. The time before that it was shock absorbers, that was about 4 years ago.
To be fair they weren't selling me a new driveshaft because they suggested I find a reconditioned one.

I'll be getting a second opinion next week but just thought I'd ask the question as it'll be bugging me all weekend.


MG CHRIS

9,322 posts

198 months

Saturday 17th August 2013
quotequote all
Would be good to know what car it is, on some rwd older cars bmw/mx5 trying to remove the driveshafts can be a nightmare to remove from the splines in the hub.

Idontdrinkrsmoke

Original Poster:

126 posts

167 months

Saturday 17th August 2013
quotequote all
e46 BMW 320i Touring.

Thanks.

MG CHRIS

9,322 posts

198 months

Saturday 17th August 2013
quotequote all
They can seize in the splines in the hub and you can if using the wrong tools fk up the end of the driveshaft mayby they did this.

Ive done similar on an older e36 even with heating up the driveshaft and on a press it snapped the casing before it moved.

lexusboy

1,101 posts

174 months

Saturday 17th August 2013
quotequote all
Shaft nut could have been seized on and they've just ragged it off with an air gun and stripped the threads off

Andyjc86

1,149 posts

180 months

Saturday 17th August 2013
quotequote all
I would guess the thread is fked, either by:

A) nut stripping it on the way off
B) shaft seized, thread damaged when large hammer hit it.
C) thread was stripped when nut went back on.

I did c recently when I was doing a customers car, I was on the phone not concentrating, didn't notice the nut was cross threaded and stuck an air gun on it. I replaced the outer cv joint foc frown

Idontdrinkrsmoke

Original Poster:

126 posts

167 months

Sunday 18th August 2013
quotequote all
Thanks for all replies. Car is going in to a proper mechanics tomorrow for a second opinion.

Mound Dawg

1,931 posts

205 months

Sunday 18th August 2013
quotequote all
Take the wheel off and look for "tool marks" on the nuts and bolts around the hub. If there aren't any, then they may well have just looked at it and decided that there was no point in doing the job because the drive shaft was knackered.