VERY slow puncture, permmanent repair options...
Discussion
Hi all. I know this has been asked before (probably) but I am going to ask it anyway. How do I find the cause of, and then repair, a slow puncture that I seem to have.
The tyre is an Eagle F1 Assy 2 and is less than 3 months (2000 miles) old. It seems to be deflating to 20 psi over the course of a few days, and interestingly, not deflating any more.
What could be causing this. Obviously a pin prick hole but wouldn't it go completely flat? Could a leaky valve be the issue? Do valves even leak and can they be replaced?
Erm, so basically, what I'm asking is, if you were me what would you do? (I'm not rich yet so would prefer not to buy another tyre!)
P.S: Apologies in advance for the spelling mistake in the title. It's really hard to keep one's spelling accurate while using their touchscreen phone while driving at excessive speed around the local industrial estate/orphanage for deaf children...
Cheers
Jimbob
The tyre is an Eagle F1 Assy 2 and is less than 3 months (2000 miles) old. It seems to be deflating to 20 psi over the course of a few days, and interestingly, not deflating any more.
What could be causing this. Obviously a pin prick hole but wouldn't it go completely flat? Could a leaky valve be the issue? Do valves even leak and can they be replaced?
Erm, so basically, what I'm asking is, if you were me what would you do? (I'm not rich yet so would prefer not to buy another tyre!)
P.S: Apologies in advance for the spelling mistake in the title. It's really hard to keep one's spelling accurate while using their touchscreen phone while driving at excessive speed around the local industrial estate/orphanage for deaf children...
Cheers
Jimbob
I had a slow puncture on a new X5 tyre. Local tyre shop put the wheel in a bath to locate the nail and then removed the nail, drilled the hole bigger and inserted a mushroom from the inside out using glue. 10 minutes later off i go £20 lighter.
Very easy and if valve it will just be changed.
Very easy and if valve it will just be changed.
I would take it to the place that fitted the tyres and ask them to check it.
I sorted one out for a friend recently that turned out to be light corrosion on the wheel rim that had prevented the tyre bead sealing properly. The tyre fitter took the tyre off and sanded the rim a bit, then refitted it and checked it again. I think it cost about £20 and has been fine since.
I sorted one out for a friend recently that turned out to be light corrosion on the wheel rim that had prevented the tyre bead sealing properly. The tyre fitter took the tyre off and sanded the rim a bit, then refitted it and checked it again. I think it cost about £20 and has been fine since.
stick100 said:
If its a alloy wheel 9 times out of ten its leaking round the rim it needs the flaking powder coat taking of round where the bead seats
Yes, agreed. That is my experience over the years particularly if when a tyre was fitted in the past those clip-on balance weights were hammered into the rim edges. Thus destroying the unseen protective paint covering on the tyre-rim seal interface. Rain and winter road salt then attacks the metal where scratched and the corrosion spreads further destroying the air pressure seal.Lost count of the times I've had slow punctures in good condition Alloy Wheels which have been damaged by heavy handed rim clip balance weight fitting.
Using a cheap plastic Mist Sprayer ( Garden Centres for about two quid ) with a 10-1 diluted Washing Up Liquid mix, I spray the whole tyre making sure the tyre-rim interface gets a good soaking. Any escaping air pressure in damaged interface areas will soon produce tell tale air bubbles in the soapy spray :~
Rim clip weights removed. You can see where they were :~


New unused Factory spare ... MG Guilty!


Extreme cases :~

After removal of the tyre and balance weight clips :~

Some outfits use sealant to "seal" the damaged interface. Rarely lasts :~

Having tyres removed, I then rub down smoothing the corroded interface areas with various grades or sand or wet and dry paper. Hand painted the unseen area after treatment with suitable silver paint. Allow to harden off for a day or so. Then take the wheel and tyre and have them refitted and balanced ... insisting that SELF-ADHESIVE balance weights are used and never rim clip versions which always damage the protective paint and soft alloy no matter how careful they are fitted. Usually hammered on quickly as I have seen in places where some folks confuse uncaring speed with a job well done.
Those damaged alloy wheel rims I repaired all hold pressure as good as new.
By the way, I used City Powder Coaters in Birmingham a couple of years back to refurbish two sets of 17" Rover Vitesse Alloys on my son's and my own 620ti. Not expensive and still looking good. Not bad for wheels close to sixteen years old :~

Gassing Station | General Gassing | Top of Page | What's New | My Stuff



