Lift trucks - not sure where to put this?
Lift trucks - not sure where to put this?
Author
Discussion

twoblacklines

Original Poster:

1,575 posts

192 months

Sunday 13th October 2013
quotequote all
At some point in the future I am going to need a proper unit on a business park as my business is expanding quickly.

I have been looking at the basics of what I really need and one of which is a forklift truck. There is only so much I can do with a hand held one. Not looking for huge vertical pallet storage, maybe about 5 pallets high, so no need for a telehandler I should think.

I have no idea on makes and models so was just looking at CaT ones, now you have a choice of diesel vs electric, has anyone any experience of either? I tend to look at electric vehicles like I would a Prius- avoid like the plague. And how does one charge them and for how long? Are they safe to leave charging overnight, with everything locked up?

Many Thanks

davepoth

29,395 posts

230 months

Sunday 13th October 2013
quotequote all
Electric is fine for inside use (and a bit of outside too), and much cleaner. You can leave them on charge overnight.

Spitbarnatt

87 posts

214 months

Sunday 13th October 2013
quotequote all
The best truck will depend on a lot of variables. But mainly how much do you intend to use the truck? Are you going to buy or lease and what is your budget? Why not LPG?

There are a lot of good trucks out there, the Cats are just a Mitsubishi in a different colour.

Electrics are fine when properly maintained.

mph1977

12,467 posts

199 months

Sunday 13th October 2013
quotequote all
part of the issues is that if you are going to 5 pallet high racking you'll be looking at needing a reach or VNA truck to reach level 5 depending on how tightly your racking is is spaced, these are nearly all ways electric .

electric or gas or diesel for Counterbalance truck depends on the use it;s put to

if it's 99% outside then gas or diesel

if it's 99% inside electric

if it's 50/50 gas

charging for electrics depends on what you want to do - many VNA , LLOP and PPT electrics have relatively easily swappable battery packs with the correct kit - where the electric CBs i've seen then not to.

twoblacklines

Original Poster:

1,575 posts

192 months

Sunday 13th October 2013
quotequote all
I don't know what that alphabet soup means?

Would be using it daily. 99% inside, outside only to remove old pallets and unload from a truck. Either way the ground would be completely flat with no obstacles such as drainage.

Is it best to buy new or second hand?

Digga

48,649 posts

314 months

Monday 14th October 2013
quotequote all
twoblacklines said:
Is it best to buy new or second hand?
We've always bought secondhand and, if you get a decent make - Yale and (s)Hyster are virtually the same thing and very good, Lindes are also very tough - that's in reasonable nick, and is easy to get spares for it will last ages. Avoid weird/cheap Chinese rubbish at all costs and do not buy new, because they will cost you way more than used.

However, you will need annual servicing and to have the lift chains tested, so you'll need an engineer/fitter to look after it. We sourced our trucks (latterly) though the local engineer we were using, on the basis that he is vouching for their condition and being expected to look after them.

You need to quantify the maximum lift weight and height, in order to know which is the optimum size. As a general rule, always get a bigger truck than you need, for safety and convenience sake.

Davel

8,982 posts

289 months

Monday 14th October 2013
quotequote all
We run diesel trucks here, as electric seem to have a habit of going flat at just the wrong time.

Our warehouses are well ventilated.

We hire ours and that includes maintenance and free mast checks every twelve months. We don't want the responsibility of maintaining them ourselves.

We use 2.5 tonne counterbalance trucks, which should give an adequate lifting height for one tonne pallets. Just bear in mind the weight and height of each pallet might prevent you from stacking at the height you want.

We also have a JCB Tele-handler for the shovel or higher level work.

Hope that this helps.

Redarress

730 posts

238 months

Monday 14th October 2013
quotequote all
Beware of charging electric forklifts overnight if you unit is not manned. Insurance companies are getting a little twitchy due to fires caused by recharging forklift batteries

Try a propane gas forklift We have always bought refurbished Cats from our local dealer who also services them twice a year for us. You will get a good one for £6 to 8k that will last for years. Try to go for a fork truck with manual hydraulic valves rather than electric ones. Simple is best. Also we.have electric Bendi trucks in out warehouse which has enabled us to have the aisles between the racking much closer than usual.
Hope that helps

mph1977

12,467 posts

199 months

Monday 14th October 2013
quotequote all
Redarress said:
<snip> Also we.have electric Bendi trucks in out warehouse which has enabled us to have the aisles between the racking much closer than usual.
Hope that helps
hence my reference to VNA with regard to the 5 pallets high storage ... to go to 5 levels of racking you'll need bendi or turret VNA kit unless you've the space to spread the racking wide enopugh to let a big reach truck do it

Kwacker

641 posts

315 months

Monday 14th October 2013
quotequote all
Just be careful who you buy one from. Both times we bought one we had issues.

When we bought the second one, the cheeky feckers even tried to deliver us the crappy one that was next to the one we had selected. We had to tell the delivery driver what to do with the wrong one. A few phone calls later and he was back with the correct machine.

Kwacker

Digga

48,649 posts

314 months

Tuesday 15th October 2013
quotequote all
Redarress said:
Beware of charging electric forklifts overnight if you unit is not manned. Insurance companies are getting a little twitchy due to fires caused by recharging forklift batteries

Try a propane gas forklift We have always bought refurbished Cats from our local dealer who also services them twice a year for us. You will get a good one for £6 to 8k that will last for years. Try to go for a fork truck with manual hydraulic valves rather than electric ones. Simple is best. Also we.have electric Bendi trucks in out warehouse which has enabled us to have the aisles between the racking much closer than usual.
Hope that helps
^This, is all good advice.

I've always favoured propane gas trucks because it's cleaner than diesel and less hassle than electric. I was at a factory once where a worker plugged a forklift into a socket intended for a mig welder and it literally blew part of the fusebox from the wall - so i was never a big fan.