80 Cabrio
Author
Discussion

Adenauer

Original Poster:

18,982 posts

267 months

Tuesday 3rd December 2013
quotequote all
My finger slipped whilst browsing Ebay last Friday, picking it up tomorrow, I hope it's not st. biggrin




Cupramax

11,007 posts

283 months

Tuesday 3rd December 2013
quotequote all
Steering wheels on the wrong side wink what engine?

Adenauer

Original Poster:

18,982 posts

267 months

Tuesday 3rd December 2013
quotequote all
2.0, couldn't get a bigger one (not that I was actually looking), as my daughter's just turned 18 wink

hman

7,497 posts

225 months

Tuesday 3rd December 2013
quotequote all
had a 2.6 v6 one of these - it wasn't fast at all - but it was a nice cruiser - albeit the scuttle shake was unnerving.

2.0 would be seriously underpowered but would get you to the shops ok I suppose.

Power hood I trust?

Powerflex those front wishbones too, soggier than wet cardboard otherwise.


Adenauer

Original Poster:

18,982 posts

267 months

Tuesday 3rd December 2013
quotequote all
hman, power hood, yes.

It'll be her first ever car so a little under powered isn't a bad thing. I don't think I'll start poly bushing, stiffening and lowering it just yet. biggrin

Adenauer

Original Poster:

18,982 posts

267 months

Tuesday 3rd December 2013
quotequote all
The Germans recommend sticking a strut brace in the front to help with the scuttle shake. Anyone think that might be a good idea?

blade7

11,311 posts

247 months

Tuesday 3rd December 2013
quotequote all
Adenauer said:
The Germans recommend sticking a strut brace in the front to help with the scuttle shake. Anyone think that might be a good idea?
Pretty sure my 2.6 80 Avant had one as standard.

Adenauer

Original Poster:

18,982 posts

267 months

Tuesday 3rd December 2013
quotequote all
blade7 said:
Pretty sure my 2.6 80 Avant had one as standard.
Yep, from what I can gather from '97 onwards they were fitted as standard, I'll get one fitted. yes

hman

7,497 posts

225 months

Tuesday 3rd December 2013
quotequote all
Mine was a 95 and it had a strut brace (possibly because it was the v6)

blade7

11,311 posts

247 months

Tuesday 3rd December 2013
quotequote all
hman said:
Mine was a 95 and it had a strut brace (possibly because it was the v6)
Could be, mine was a 92 I think.

Vince70

1,944 posts

225 months

Tuesday 3rd December 2013
quotequote all
I have a nice low mileage one myself in 2.3 flavour which was bought 2 years ago now.


There is a bit of scuttle shake on the old 80 but it only ever shows itself on badly potholed roads (so thats 99.9 of our roads lol)

The only weak points I've ever heard of on the 80 is the heater matrix and the front suspension top mounts (never had a problem myself) and mine is 21 years old.

The 2 litre lump might be a bit on the slow side but for reliability and servicing costs it can't be beaten,, my father had an A6 which had the same lump which he recently sold to a fellow piston head and he never had a single problem with it in the 4 years he owned it..

You may get a problem with a dodgy fuel and temp gauge again a very easy fix which takes 15 minutes and 10 pence for four small washers.



Yours looks a nice car. But you need to fit an electric aerial (wiring is already in the boot) for that added retro look lol

Its handy to know about the strut brace being fitted on the later variants though so.. I'm going to be looking myself on eBay for a cheap one to retro fit..

Edited by Vince70 on Tuesday 3rd December 14:47

Adenauer

Original Poster:

18,982 posts

267 months

Tuesday 3rd December 2013
quotequote all
Cheers, Vince, that all sounds beautifully positive, just what I wanted to hear thumbup

hman

7,497 posts

225 months

Tuesday 3rd December 2013
quotequote all
hmmm yes heater matrix - that went on an audi coupe quattro I sold to a friend antifreeze on the mats was the giveaway - then one day it totally let go = scalding hot water into the footwell!!!

Dash board out job to replace, so he plugged the hoses and and sold the car with cold air only!.

Also heater fans have a habit of blowing the resistor pack which means all or nothing.

The cable and multiplug to the roof pump can breakdown leaving you with a manual roof only - and boot switches can fail which again stop the roof working.

Something is making me think of the brake bomb problem with these too...

Oh yes and rear calipers seize up very easily due to their rubbish design - make sure they arent dragging...

Adenauer

Original Poster:

18,982 posts

267 months

Tuesday 3rd December 2013
quotequote all
Thanks for that, hman, that nicely balanced out Vince's enjoyable post. laugh

Vince70

1,944 posts

225 months

Tuesday 3rd December 2013
quotequote all
Well I'd rather my glass half full than half empty lol smile

Yertis

19,742 posts

297 months

Tuesday 3rd December 2013
quotequote all
Vince70 said:
You may get a problem with a dodgy fuel and temp gauge again a very easy fix which takes 15 minutes and 10 pence for four small washers.
Could you elaborate on that Vince? I just bought my daughter a Coupe, the temp reads high (it's spot on when checked with VAG-COM) and the fuel reads low.

The matrix was starting to leak too - hopefully a can of K-Seal has sorted that.

hman

7,497 posts

225 months

Wednesday 4th December 2013
quotequote all
Yertis, they fail along a seam - once they go, THEY GO!!!

Yertis

19,742 posts

297 months

Wednesday 4th December 2013
quotequote all
hman said:
Yertis, they fail along a seam - once they go, THEY GO!!!
Thanks for that hman, don't want her scalding her legs so I'll order one in. That's the Christmas break taken care of then – had planned to refurb the diff on me Quattro.

Vince70

1,944 posts

225 months

Wednesday 4th December 2013
quotequote all
Yertis said:
Vince70 said:
You may get a problem with a dodgy fuel and temp gauge again a very easy fix which takes 15 minutes and 10 pence for four small washers.
Could you elaborate on that Vince? I just bought my daughter a Coupe, the temp reads high (it's spot on when checked with VAG-COM) and the fuel reads low.

The matrix was starting to leak too - hopefully a can of K-Seal has sorted that.
Sorry for the late reply.
When I took my dash out I found that mine needed a new temp gauge because a previous owner had already played with my gauge and had broke the adjuster so my gauge didn't work so I bought a NOS one off eBay for a tenner and refitted it..

Plus I fitted new small washers behind the temp and fuel gauges and cleaned up the contacts just to be on the safe side, but my circuit board was very dirty so I took all the clocks off and stripped it down and cleaned it with a bit of contact cleaner as I thought while I was at it a may as well do the job properly..

On the temperature gauge there's an adjustment screw on the back of the gauge which can be tweaked with a small screwdriver which sounds like that's your problem rather than the contact problem as otherwise your gauge would work intermittently .

As for the fuel gauge there's also an adjuster on the front of the clocks but to adjust that one you actually have to take the unit apart.

You can see the adjuster for the fuel gauge on the front of the dash.
It's the one that looks like a trip reset that doesn't actually do anything, but to adjust the gauge the clocks have to come apart...

When I was playing with my fuel gauge I actually adjusted it to under read the amount of fuel slightly on mine so that I wouldn't run out lol.


Also six months later my temp gauge packed up again and this time I thought it must of been down to my handy work so I stripped the dash down again to look for a dry joint only to find out it was a faulty coolant sensor lol...

Also there's a very good how to guide on the internet somewhere on how to change the matrix.. It looks quite daunting as the whole dash comes out but apparently it not as bad as it looks and you don't need any specialist tools and it can be done in a day and it's not a dirty job,
I wouldn't go down the K seal route as you may block up the water ways or the rad.

I also think the guide includes vital tea and hobnob breaks and a new matrix can be had for less than 40 quid if you shop around..

When my matrix goes I will have a go myself as 80's are incredibly cheap so it's hardly worth paying a garage a kings ransom to get a new one fitted, but then again I can't stop myself tinkering..
I blame it all those Airfix kits my parents bought me as a kid lol

I did try looking for the old gauge to take a photo of the back for reference but I've thrown it in the shed somewhere never to be seen again..

Edited by Vince70 on Wednesday 4th December 16:18

Yertis

19,742 posts

297 months

Wednesday 4th December 2013
quotequote all
Vince70 said:
Sorry for the late reply.
When I took my dash out I found that mine needed a new temp gauge because a previous owner had already played with my gauge and had broke the adjuster so my gauge didn't work so I bought a NOS one off eBay for a tenner and refitted it..

Plus I fitted new small washers behind the temp and fuel gauges and cleaned up the contacts just to be on the safe side, but my circuit board was very dirty so I took all the clocks off and stripped it down and cleaned it with a bit of contact cleaner as I thought while I was at it a may as well do the job properly..

On the temperature gauge there's an adjustment screw on the back of the gauge which can be tweaked with a small screwdriver which sounds like that's your problem rather than the contact problem as otherwise your gauge would work intermittently .

As for the fuel gauge there's also an adjuster on the front of the clocks but to adjust that one you actually have to take the unit apart.

You can see the adjuster for the fuel gauge on the front of the dash.
It's the one that looks like a trip reset that doesn't actually do anything, but to adjust the gauge the clocks have to come apart...

When I was playing with my fuel gauge I actually adjusted it to under read the amount of fuel slightly on mine so that I wouldn't run out lol.


Also six months later my temp gauge packed up again and this time I thought it must of been down to my handy work so I stripped the dash down again to look for a dry joint only to find out it was a faulty coolant sensor lol...

Also there's a very good how to guide on the internet somewhere on how to change the matrix.. It looks quite daunting as the whole dash comes out but apparently it not as bad as it looks and you don't need any specialist tools and it can be done in a day and it's not a dirty job,
I wouldn't go down the K seal route as you may block up the water ways or the rad.

I also think the guide includes vital tea and hobnob breaks and a new matrix can be had for less than 40 quid if you shop around..

When my matrix goes I will have a go myself as 80's are incredibly cheap so it's hardly worth paying a garage a kings ransom to get a new one fitted, but then again I can't stop myself tinkering..
I blame it all those Airfix kits my parents bought me as a kid lol

I did try looking for the old gauge to take a photo of the back for reference but I've thrown it in the shed somewhere never to be seen again..
Thanks Vince, much appreciated. I might get a spare set of clocks anyway. Totally with you on the Airfix thing - that's where I started too. K-Seal already in as the car was steaming up all the time, but I'm really not too worried about that stuff, I think there's alot of scaremongering about that sort of stuff and some manufacturers chuck it in as a matter course. Downloaded the instructions for the matrix replacement, along with how to remove the airbag without blowing yourself up...

8b is a greatly under-rated car IMO.