Cant get Fault code reader to work
Cant get Fault code reader to work
Author
Discussion

Gmw76

Original Poster:

104 posts

182 months

Thursday 5th December 2013
quotequote all
Hi

Hope someone can help had the car only a few days but in anticipation of some common faults bought a U480 fault code reader a while ago. It is the orange one which has had mention on here before. My car is 08 V8V. I plug in the reader and it says memoscan. I then turn on ignition and press enter. It scans through protocols and then says failed link.

Am i in the correct socket under dash slightly left of steering column?

Is this reader known as good to work with my car?

Unlike some images I have seen my car appears to have only a single grey socket on the same bracket as the footwell light.

Regards
Mark

Edited by Gmw76 on Thursday 5th December 17:53

Gettoff

1,434 posts

238 months

Thursday 5th December 2013
quotequote all
Make sure you are using the socket nearest the door, there are two side by side, the right one is for engine etc. and the left for body or something.

I have the exact same reader, 07MY V8 and have had no issues.

Gmw76

Original Poster:

104 posts

182 months

Thursday 5th December 2013
quotequote all
Can you confirm it is on the drivers side?

I am starting to believe that after a certain MY only one socket is there. I have seen internet images with 2 and some with one. The only thing on the single bracket is a light and a single socket. Similar to this link.

http://www.6speedonline.com/forums/attachment.php?...

Mark

Gettoff

1,434 posts

238 months

Thursday 5th December 2013
quotequote all
Just checked mine, and its different, two connectors. Not sure if it is just one on the newer cars, hopefully someone can confirm for you.

Have you tried the reader on any other car to confirm its functioning ok?

Gmw76

Original Poster:

104 posts

182 months

Thursday 5th December 2013
quotequote all
Thanks for your help so far.

Just tried it on a freelander and it works fine. So either something different on mine or bad socket connection. Will keep trying. I am putting ignition on but not starting car.

Mark

DB9VolanteDriver

2,661 posts

207 months

Thursday 5th December 2013
quotequote all
Powertrain is on driver's side and body port on the passenger's side for those cars that no longer have both sockets on the driver's side.

Gmw76

Original Poster:

104 posts

182 months

Thursday 5th December 2013
quotequote all
Thanks

So I am in the right socket so just need to suss out why it wont communicate.

V12Vantage

477 posts

170 months

Thursday 5th December 2013
quotequote all
Check that the USB port fuse isn't blown, it might be the same circuit as the accessory sockets. If there is no power at the socket it won't power up the code reader.

Gmw76

Original Poster:

104 posts

182 months

Friday 6th December 2013
quotequote all
Thanks.

Reader powers up and scans through different communications protocols. Then it says failed to read. I take it I shouldnt need to start the engine. I am turning ignition on.

Does anyone else use this particular code reader on MY08 car or newer?

Mark

brakedwell

1,229 posts

230 months

Friday 6th December 2013
quotequote all
The sockets in 05MY DB9 looks like this


Gmw76

Original Poster:

104 posts

182 months

Friday 6th December 2013
quotequote all
Definately only one socket on my car. U480 works on a freelander but fails communication with Vantage. Others report success with this unit but they are earlier cars up to MY08 with twin sockets.

Was the system changed?

Can anyone suggest a known working reader for MY08 ?

Thanks
Mark

DB9VolanteDriver

2,661 posts

207 months

Friday 6th December 2013
quotequote all
Gmw76 said:
Definately only one socket on my car. U480 works on a freelander but fails communication with Vantage. Others report success with this unit but they are earlier cars up to MY08 with twin sockets.

Was the system changed?

Can anyone suggest a known working reader for MY08 ?

Thanks
Mark
To be accurate, you do have two sockets. It's just that the other one is in the other foot well. You have nothing to lose by plugging your reader into the other port and see what happens. When plugging in to the body port, a 'can't communicate' message is typical.

Jalfonse

241 posts

171 months

Friday 6th December 2013
quotequote all
I have the same reader and understand what you mean, the timing of hitting scan button and switching ignition is crucial to avoid this problem, I can get it to work if I have it connected and then press the scan button and then very quickly turn the ignition on, any variation or delay gives me the error code.

Gmw76

Original Poster:

104 posts

182 months

Friday 6th December 2013
quotequote all
Thanks for that Jalfonse.

Is you car the same age or newer than mine ?

Just tried again trying to be quick and various other combinations.

Starting to think I need an alternative code reader.

Anyone got a reliabe code reader suggestion for my model year?

Mark



Edited by Gmw76 on Friday 6th December 15:23

Jalfonse

241 posts

171 months

Friday 6th December 2013
quotequote all
Mine is a 2006 V8V, still takes me a few goes to get the thing right, good luck

Manwhoneverwas

598 posts

162 months

Friday 6th December 2013
quotequote all
I purchased one identical to this and it has been used numerous times to reset the "Emission Service Required" faux pas (select the Jaguar diagnostic option since AM is not listed on the menu)
I have a 2008 MY V8VR with the single diagnostic port under the steering column

http://www.ebay.co.uk/itm/D900-Universal-OBD2-EOBD...


Gmw76

Original Poster:

104 posts

182 months

Friday 6th December 2013
quotequote all
Thanks

Got one on order so will report back on progress.

Many thanks
Mark

Shnozz

30,693 posts

302 months

Monday 2nd April 2018
quotequote all
Jalfonse said:
I have the same reader and understand what you mean, the timing of hitting scan button and switching ignition is crucial to avoid this problem, I can get it to work if I have it connected and then press the scan button and then very quickly turn the ignition on, any variation or delay gives me the error code.
I wonder if you can elaborate on this a little as I too seem to be having the same issue with that same code reader not being able to link to the car...

raceboy

13,943 posts

311 months

Tuesday 3rd April 2018
quotequote all
On the subject of OBD II fault code readers....is there a 'recommended' best buy?
Ideally the cheapest possible, I don't want anything over complicated or fancy, if my last 10 months of ownership is anything to go by...and I hope it is, I just want the facility to turn off the "Emissions Systems Service Required" message every 5 months. rolleyes

northernmedia

1,988 posts

169 months

Tuesday 3rd April 2018
quotequote all
I've got this one.
Works fine to clear those intermittent 'emission service warning' lights wink

https://www.ebay.co.uk/itm/Car-Fault-Engine-Diagno...