Discussion
Well sort of... Dry sump Roush/Ford 351w, 4 speed jerico/toploader, twinplate clutch and a 9 inch coil sprung live axle.
Makes the Monaro seem refined and sophisticated.


Doesn't start well at present. Two pumps of fuel and it fires instantly and dies. If you try to keep your toe in a bit an instant carb fire results.
Fuel from the Holley blue smack on 6 psi. So it could be primary jetting or bad ignition timing.
Cold weather + Chokeless Holley double pumper with mechanical secondaries and a 1 inch throttle travel may also be a factor. Probably has quite a big cam too.
I have some 100 octane leaded so may try that.
Anyone on here have a theory?
Makes the Monaro seem refined and sophisticated.
Doesn't start well at present. Two pumps of fuel and it fires instantly and dies. If you try to keep your toe in a bit an instant carb fire results.
Fuel from the Holley blue smack on 6 psi. So it could be primary jetting or bad ignition timing.
Cold weather + Chokeless Holley double pumper with mechanical secondaries and a 1 inch throttle travel may also be a factor. Probably has quite a big cam too.
I have some 100 octane leaded so may try that.
Anyone on here have a theory?
richie slow said:
The Monaro in the background has saved the thread.
Normally a title like that would get numerous requests for thread deletion
I've still got the monaro obviously! The toy tractor in the background is more advanced than both... Cvt transmission Normally a title like that would get numerous requests for thread deletion

.Know anything about four barrel carbs / distributors then Richie?
M11 MFP said:
I've still got the monaro obviously! The toy tractor in the background is more advanced than both... Cvt transmission
.
Know anything about four barrel carbs / distributors then Richie?
Many years ago I might have tried to help (probably fruitlessly). The only carbs I ever see nowadays are on the niece's racing mini and that's not likely to be relevant here.
.Know anything about four barrel carbs / distributors then Richie?
Top marks for taking on what looks like a great project. Good luck with it
gsd2000 said:
This a new toy then?
Yep. Wasn't so much cash, but has a few problems as stated above. I think, fingers crossed the motor is good. Doesnt appear to have any blow by and has good oil pressure. It's certainly well used - the series they raced included pretty wild driving at times. Cost of tyres / dampers (shot I think on the front) is pretty eye watering but otherwise it's simple and built like a tank.stick100 said:
What race series ? I only ask as I want to do somthing like this
Eurocar V8. Long defunct unfortunately and not coming back. The similar 4 cyl SHP pickups are still going strong however. This is a two seater now. Trackdays only. Could run in CNC northern saloons etc with a total rebuild, but it wouldn't be competetive against old DTM cars etc. Also that requires a lot of money and preparation time.
Thanks for the opinion Gareth, Rich.
Runs fine when warm, so as Richard says no choke and the lean state when cold are probably the main problem. I have a 4150 (780 cfm) elec choke holley in the garage, but its jetted for a milder 302 and has vacuum secondaries, so probably not worth the hassle. I'll look into refreshing the carb and at the choked mechanical secondary options. Also at getting the ignition and jetting set up by someone informed.
So which did you go in at Mallory Gareth? V6 or V8. Guess you got to drive - there weren't many two seaters about then.

Runs fine when warm, so as Richard says no choke and the lean state when cold are probably the main problem. I have a 4150 (780 cfm) elec choke holley in the garage, but its jetted for a milder 302 and has vacuum secondaries, so probably not worth the hassle. I'll look into refreshing the carb and at the choked mechanical secondary options. Also at getting the ignition and jetting set up by someone informed.
So which did you go in at Mallory Gareth? V6 or V8. Guess you got to drive - there weren't many two seaters about then.
Richard Ingram said:
Probably 150 rwhp 
Castle Combe pre chicane, 1:04 @ 103 mph ... must go round the corners without lifting then 

stigmundfreud said:
Also what happened to the euro v8 series?
http://www.nascarwheleneuroseries.com/cars-specs/ Still going for 2014, but these are no relation to the above. Quite a lot bigger dimensions.M11 MFP said:
Castle Combe pre chicane, 1:04 @ 103 mph ... must go round the corners without lifting then 
If you want some help, I can put you in touch with an old mate of mine who raced them. PM me for a phone number if you need. Or try Sonny Howard of SHP Motorsport who started and ran the Eurocar series.
(BTW, I was in a V6, they fitted passenger seats for PR events, and our company sponsored the car)
Do you know whose car you have??.
Thanks Gareth. Sonny Howard is just up the road from me in Littleport. Wasn't going to bother him as these cars haven't been his business for many years, but thought of contacting the secretary to find the original spec / build sheet for some of the unmarked componentry, geometry etc. I know of a few people who still have them, some started a Facebook group 2 years ago. Lots of photos if you are interested.
https://www.facebook.com/eurocar.racing#!/groups/3...
Really have no idea whos car it was, there weren't many V8s with white/silver spaceframes though. Maybe Chris Dawkins?
https://www.facebook.com/eurocar.racing#!/groups/3...
Really have no idea whos car it was, there weren't many V8s with white/silver spaceframes though. Maybe Chris Dawkins?
Edited by M11 MFP on Wednesday 1st January 16:52
M11 MFP said:
Thanks Gareth. Sonny Howard is just up the road from me in Littleport. Wasn't going to bother him as these cars haven't been his business for many years, but thought of contacting the secretary to find the original spec / build sheet for some of the unmarked componentry, geometry etc. I know of a few people who still have them, some started a Facebook group 2 years ago. Lots of photos if you are interested.
https://www.facebook.com/eurocar.racing#!/groups/3...
Really have no idea whos car it was, there weren't many V8s with white/silver spaceframes though. Maybe Chris Dawkins?
The guys I remembered racing were Mike Jordan (Mac Tools), Stevie Hodgson, Kevin Clarke, Peter Falding and I Barry Lee, of Hot Rod racing fame, raced one too sponsored by Hewlett Packard (his was white I think).https://www.facebook.com/eurocar.racing#!/groups/3...
Really have no idea whos car it was, there weren't many V8s with white/silver spaceframes though. Maybe Chris Dawkins?
Edited by M11 MFP on Wednesday 1st January 16:52
Shame that they never really took off here, but I think they were quite expensive at the time. I think IIRC a firm called Tooheys built and prepped the F**d V8's.
Edited by MyM8V8 on Wednesday 1st January 18:56
MyM8V8 said:
The guys I remembered racing were Mike Jordan (Mac Tools), Stevie Hodgson, Kevin Clarke, Peter Falding and I Barry Lee, of Hot Rod racing fame, raced one too sponsored by Hewlett Packard (his was white I think).
Shame that they never really took off here, but I think they were quite expensive at the time. I think IIRC a firm called Tooheys built and prepped the F**d V8's.
Yep, John Toovey did the rebuilds when the crate Roush motors went tits up. Barry 'Leapy' Lee's had a blue spaceframe and sold at HH race-retro auction in fairly ropey condition about 3 years back.Shame that they never really took off here, but I think they were quite expensive at the time. I think IIRC a firm called Tooheys built and prepped the F**d V8's.
Edited by MyM8V8 on Wednesday 1st January 18:56
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff


