How to get a level floor in a marquee on a sloping pitch?
How to get a level floor in a marquee on a sloping pitch?
Author
Discussion

singlecoil

Original Poster:

35,887 posts

277 months

Thursday 9th January 2014
quotequote all
A year ago I exhibited at the local county show and it went well. However, coping with the sloping floor was a problem I would sooner avoid in the future. I've considered hiring an exhibition trailer but they are not normally more than 3 metres wide, and we found the 6M X 6M marquee ideal, and wouldn't want to go any narrower.

Any ideas?

CRB14

1,494 posts

183 months

Thursday 9th January 2014
quotequote all
singlecoil said:
A year ago I exhibited at the local county show and it went well. However, coping with the sloping floor was a problem I would sooner avoid in the future. I've considered hiring an exhibition trailer but they are not normally more than 3 metres wide, and we found the 6M X 6M marquee ideal, and wouldn't want to go any narrower.

Any ideas?
Speak to a scaffolder? They may be able to provide you with a stage type base and you could overlay ply on top. Should be quite cheap to hire too although you'd have to bring them in to erect and dismantle.

singlecoil

Original Poster:

35,887 posts

277 months

Thursday 9th January 2014
quotequote all
CRB14 said:
singlecoil said:
A year ago I exhibited at the local county show and it went well. However, coping with the sloping floor was a problem I would sooner avoid in the future. I've considered hiring an exhibition trailer but they are not normally more than 3 metres wide, and we found the 6M X 6M marquee ideal, and wouldn't want to go any narrower.

Any ideas?
Speak to a scaffolder? They may be able to provide you with a stage type base and you could overlay ply on top. Should be quite cheap to hire too although you'd have to bring them in to erect and dismantle.
That's a thought, but I guess it would need to be a minimum height from the ground, and if there was any other solution that had a lower minimum height it would make acquisition of the appropriate marquee a good deal easier, as well as reducing the step height.

surveyor

18,707 posts

215 months

Thursday 9th January 2014
quotequote all
what about a stage?

singlecoil

Original Poster:

35,887 posts

277 months

Thursday 9th January 2014
quotequote all
surveyor said:
what about a stage?
What sort of stage do you have in mind?

surveyor

18,707 posts

215 months

Thursday 9th January 2014
quotequote all
something like this.

not a clue what the cost is

http://www.origintechnicalproductions.co.uk/outdoo...

RichB

56,485 posts

315 months

Thursday 9th January 2014
quotequote all
What's the fall? I once had a good sized marquee in my garden with about a 1m drop from side to side. They simply put in a floor which they levelled before building the marquee over the top.

singlecoil

Original Poster:

35,887 posts

277 months

Thursday 9th January 2014
quotequote all
RichB said:
What's the fall? I once had a good sized marquee in my garden with about a 1m drop from side to side. They simply put in a floor which they levelled before building the marquee over the top.
Unfortunately I can't know the fall until I get the pitch, and they are not even marked out until a couple of weeks before the event. I'd prefer to use the show contractor as the marquee supplier, and they don't offer anything such as you describe. Some kind of solution that I could do myself would be best, even if it costs me some money.

Chrisgr31

14,299 posts

286 months

Friday 10th January 2014
quotequote all
If you are going to do it yourself surely all you need to do is get some sheets of ply, and batton under them, so they will drop into a frame you build. The frame is potentially more complex but you can design it in advance so it bolts together and just put legs on it of the appropriate length. Most of it, bar the bits used for the legs (due to differential lengths) would be reusable. Effectively as you would for a deck in your garden.


The question then comes whether the marquee sits on the floor, or the floor fits in the marquee.

poj

811 posts

219 months

Friday 10th January 2014
quotequote all
Hire a digger

mattdaniels

7,362 posts

313 months

Friday 10th January 2014
quotequote all
Have you enquired with the show organiser? Presumably other stallholders may have a similar issue, there may be a common solution?

mad4amanda

2,410 posts

195 months

Friday 10th January 2014
quotequote all
Chrisgr31 said:
If you are going to do it yourself surely all you need to do is get some sheets of ply, and batton under them, so they will drop into a frame you build. The frame is potentially more complex but you can design it in advance so it bolts together and just put legs on it of the appropriate length. Most of it, bar the bits used for the legs (due to differential lengths) would be reusable. Effectively as you would for a deck in your garden.


The question then comes whether the marquee sits on the floor, or the floor fits in the marquee.
be careful here, we were at an event about 10 years ago where a floor such as this collapsed. Several people needed hospital treatment and one suffered a head injury it became a major issue for the show organiser and he was prosecuted along with the diy stallholder under H&S for not having competently built a safe structure and no risk assessment. It changed how we operated and increased cost dramatically as we had to use a system of scaffolding supported by piles to support any floor which had to be inspected and signed off before covering.
I would be talking to the organiser about a solution.


Edited by mad4amanda on Friday 10th January 20:43

singlecoil

Original Poster:

35,887 posts

277 months

Friday 10th January 2014
quotequote all
mattdaniels said:
Have you enquired with the show organiser? Presumably other stallholders may have a similar issue, there may be a common solution?
I've done the show before, it's not an issue to any other stallholder as far as I'm aware, but then they're not showing furniture.

I think most likely I'm going to have two display areas on raised platforms each about 2.4 x 3.6 metres within the marquee, and am currently looking into good ways to achieve this in a knock-down form so they can be assembled on site briskly.

Chrisgr31

14,299 posts

286 months

Saturday 11th January 2014
quotequote all
Your problem comes in determining how great the slope is going to be. Whilst acknowledging the comments of the post above a timber construction could work although you'd have to use bearers on the ground to ensure that your vertical supports do not sink and ensure you use the correct sized timber!

You can get rostrum which work on a similar basis. Side panels which are hinged together to enable them to flat pack, pull them out to a rectangle and drop the top (floor) in. However they will be to a fixed height so no good for you.

If people are going to be standing on your plinths to view, sit in etc you furniture I would be inclined to raise the whole floor or you are going to run into dangers of creating a trip hazard, people stumbling off etc.

Brother D

4,452 posts

207 months

Saturday 11th January 2014
quotequote all
Depending on the slope half a foot can be packed out by timber. But any more we would have a scaffolding company in. PM if you want any info on Marquees or scaffolding recommendations

dave123456

4,145 posts

178 months

Saturday 11th January 2014
quotequote all
how many items to display? can you not make a small stand for each and chop the legs off on site to level? gets round the h&s issue.

kVA

2,460 posts

236 months

Saturday 11th January 2014
quotequote all
dave123456 said:
how many items to display? can you not make a small stand for each and chop the legs off on site to level? gets round the h&s issue.
Beat me to it - exactly what I was going to suggest - a plinth for each individual item

singlecoil

Original Poster:

35,887 posts

277 months

Saturday 11th January 2014
quotequote all
The stuff I am showing will be home office and home entertainment centre set-ups, and I will need the 3.6mtr x 2.4mtr platforms mentioned earlier. That will allow enough space for the displays themselves which will go against dummy walls, and viewers.

Based on some of the suggestions made, these are the lines I am now thinking along-

I can make each platform out of 3 x 8x4 sheets with something like 180mm joists (to give a single step of 200mm) so that they can be bolted together on site, so it's just a question of how best to level them, some kind of adjustable legs onto plywood load spreaders might be best, though ideally it would incorporate a way of adjusting the legs from above, so that the platforms don't require too much site assembly.

I'm going to think about this some more, I've started drawing something and will post it when ready for further comments.

Thanks everybody

Loaded1me

189 posts

225 months

Saturday 11th January 2014
quotequote all
Hire steel deck, or metro deck staging and use screw jack legs (see page 41 of the link below). Steel deck and metro deck is rated to 7.5T loading per deck, so more than enough loading to take what you need. Hire from the marquee company (as they'll use it for the stage) or any theatre suppliers (hundreds around the country).Quick to put together, and rated.

HTH.

http://www.steeldeck.com/sg_subpage_media/dl/steel...