New head unit in at last, got a few questions...
Discussion
So my JVC bluetooth/usb headunit is in at last, and it all fit together nicely (thanks in part to those lovely metal brackets from the group buy), just got a couple of questions:
The wire for the bluetooth microphone - the microphone is currently near the rear view mirror, I ran the wire up the A pillar, but I can't move the trim to put the wire behind, seems quite difficult to move, there seems to be NO gap between it and the windscreen, that I normally use for this type of thing. Any suggestions for this gratefully received.
Steering wheel controls - got a PAC unit from the US, didn't bother to install as I got too cold, but is this an easy fit, I know it needs a power connection but what other wires do I need to cut into, and how do I connect it to the car loom? How do it connect to the plug on the car's loom?
Thanks.
The wire for the bluetooth microphone - the microphone is currently near the rear view mirror, I ran the wire up the A pillar, but I can't move the trim to put the wire behind, seems quite difficult to move, there seems to be NO gap between it and the windscreen, that I normally use for this type of thing. Any suggestions for this gratefully received.
Steering wheel controls - got a PAC unit from the US, didn't bother to install as I got too cold, but is this an easy fit, I know it needs a power connection but what other wires do I need to cut into, and how do I connect it to the car loom? How do it connect to the plug on the car's loom?
Thanks.
I ran my wire in exactly the same place with no problems at all just used a piece of plastic (credit card) to wedge the wires between, all fits nicely no need to remove anything.
The PAC unit is a simple job and from memory requires you to cut in to about 3 or 4 of the wires in the audio loom, the instructions that come with it will tell you all you need to know, you should be able to access the loom from the passengers foot well by removing a plastic cover near the back of the dash then you can gain access to the loom to cut in, took me all of about 15 mins, just make sure you test before putting it all back together.
Any problems more than happy to assist.
The PAC unit is a simple job and from memory requires you to cut in to about 3 or 4 of the wires in the audio loom, the instructions that come with it will tell you all you need to know, you should be able to access the loom from the passengers foot well by removing a plastic cover near the back of the dash then you can gain access to the loom to cut in, took me all of about 15 mins, just make sure you test before putting it all back together.
Any problems more than happy to assist.
VinceM said:
Thanks. I see in another post from 2012 that you used some black sticky plastic to cover the fascia adapter - where did you get this from as mine currently looks crap, and if I can improve it then I will.
Got them on ebay i have loads left if you want them, however i am thinking of painting mine with black bumper spray as im not 100% happy with the finish, its far better than standard but i strive for perfection or as close to, someone did the same with plastic bumper spray and the out come looked very tidy.maxmc2 said:
VinceM said:
Thanks. I see in another post from 2012 that you used some black sticky plastic to cover the fascia adapter - where did you get this from as mine currently looks crap, and if I can improve it then I will.
Got them on ebay i have loads left if you want them, however i am thinking of painting mine with black bumper spray as im not 100% happy with the finish, its far better than standard but i strive for perfection or as close to, someone did the same with plastic bumper spray and the out come looked very tidy.its ans easy enough job to do i have done a few now, hardest part is programming the dam thing. word of warning tho the Pac units do not work 100% of the time, but you only notice this relly if you change tracks a lot, i think it might have something to do with the electrical system in the car, as its not the cleanest supply
Thanks for the advice - I'll use some old ISO pis I've got from an old adapter I bought in error to connect to the cars loom. Will look at the tel thing with the white plug and hopefully can do the same for the power.
Just need to locate the USB slot now and sort microphone wire.
Thanks Mark for the plastic.
Just need to locate the USB slot now and sort microphone wire.
Thanks Mark for the plastic.
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff


