Not again ..... crankshaft spacer

[Sardonicus]

In my over zealous clean up operation of spilt coolant, oil etc on the cardboard and blanket under my car on engine removal (removed timing cover and pulley while in situ) & everyday work distractions I have lost my crankshaft spacer that sits between the front pulley and oil pump gears the bins have already been emptied so its long gone can anyone oblige please?

[Alexdaredevils]

I think Derek has a spare. .......

[Sardonicus]

Thanks Alex anyone that comes up trumps gets one of these too

[jr6yam]

Street Machine! I've a copy of the first issue somewhere
Henry Highrise

[macdeb]

jr6yam said:

Street Machine! I've a copy of the first issue somewhere
Henry Highrise

Bloody 'ell I remember that! As a consequence I later had a 1960 Vauxhall Velox [wrap around screen, 'knee breaker'] with a small block Ford V8.

[jr6yam]

macdeb said:

jr6yam said:

Street Machine! I've a copy of the first issue somewhere
Henry Highrise

Bloody 'ell I remember that! As a consequence I later had a 1960 Vauxhall Velox [wrap around screen, 'knee breaker'] with a small block Ford V8.

It's been restored and is back on the road, still awesome.
Oh, and I spelt it wrong; it's Hirise

[mattrosersv]

Think I must have one in a drawer somewhere.

Just escaping my newborn daughter for an early hours garage session shortly (only way I can make any progress with projects these days). Will check.

Matt

[Sardonicus]

mattrosersv said:

Think I must have one in a drawer somewhere.

Just escaping my newborn daughter for an early hours garage session shortly (only way I can make any progress with projects these days). Will check.

Matt

Much appreciated

[mattrosersv]

Have been looking out for it for past few days- but no joy yet. Just finished my land rover project so will have a clear up tomorrow and will let you know for definite one way or the other.

Matt

[db484bhpv8]

Alexdaredevils said:

I think Derek has a spare. .......

I had one lying about for a short time but am using it again now

[spend]

Are you sure you had/need a spacer on your engine?

or are you fitting the 4.6 bottom end...

[phazed]

Look what I found............

[mattrosersv]

Nice one Phazed as I have had no luck with my search/tidy up this morning. I know it is somewhere.....

[spend]

mattrosersv said:

Nice one Phazed as I have had no luck with my search/tidy up this morning. I know it is somewhere.....

I don't think that washer is what Simon is asking for...

That doesn't fit between the oil pump gear and damper.....

[TV8]

phazed said:

Look what I found............

Is that the source of your rattle Peter?

[phazed]

spend said:

I don't think that washer is what Simon is asking for...

That doesn't fit between the oil pump gear and damper.....

Quite right Dave.............I must of had a moment

[LongBaz383BHP]

phazed said:

Look what I found............

Im having flashbacks to a bad time.

[mattrosersv]

Nice one Phazed as I have had no luck with my search/tidy up this morning. I know it is somewhere.....

[db484bhpv8]

Dont forget.

[Sardonicus]

spend said:

I don't think that washer is what Simon is asking for...

That doesn't fit between the oil pump gear and damper.....

Correct again I see something drop under the car when the front cover was removed and presumed it was said spacer it was not after trial fitting the crank up this morning to CC pistons and deck I can only assume it was my dizzy bung because that's now AWOL. So for today the plum award goes to Simon/Me

Edited by Sardonicus on Monday 20th January 10:33