GForce 1320 Kit
Author
Discussion

S800VXR

Original Poster:

5,877 posts

231 months

Monday 27th January 2014
quotequote all
Anyone have their anti wheel hop drive shafts fitted and if so are they any good at reducing wheel hop when doing burn outs...?

007 VXR

64,187 posts

218 months

Monday 27th January 2014
quotequote all
Got it on mine, no issues smile

S800VXR

Original Poster:

5,877 posts

231 months

Monday 27th January 2014
quotequote all
What do you have Mark? They do shafts, complete boltins and different levels.

007 VXR

64,187 posts

218 months

Monday 27th January 2014
quotequote all
level 2 drive shafts iirc

S800VXR

Original Poster:

5,877 posts

231 months

Monday 27th January 2014
quotequote all
Cheers, will see what they do for mine then.

ARAF

20,759 posts

254 months

Monday 27th January 2014
quotequote all
Not so sure you'll need them on a VXR8. Rear suspension design is much better at coping with that sort of thing.

EssexVXR8

1,790 posts

218 months

Monday 27th January 2014
quotequote all
S800VXR said:
Cheers, will see what they do for mine then.
Nope not any more they don't !!! Speak to Roger at Monkfish

S800VXR

Original Poster:

5,877 posts

231 months

Monday 27th January 2014
quotequote all
That was short lived! Will Roger Sat so chatting then.

Tried a burnout stock and it does hop about a bit!

007 VXR

64,187 posts

218 months

Monday 27th January 2014
quotequote all
Have seen S/C VXR8s hopping too yes

ringram

14,702 posts

279 months

Monday 27th January 2014
quotequote all
ARAF said:
Not so sure you'll need them on a VXR8. Rear suspension design is much better at coping with that sort of thing.
You most certainly do need them.

Got just the drivers side for mine a while back. Definitely helps.. a lot..

Take a look at the GTS one shaft looks about 3" thick!

gsd2000

11,515 posts

214 months

Monday 27th January 2014
quotequote all
Driveshaft shop (DSS) or BMR

MyM8V8

9,468 posts

226 months

Tuesday 28th January 2014
quotequote all
Can someone tell me if VXR8 shafts are the same as the previous models?

If so get the BMR unit for the driver side.

Edited by MyM8V8 on Tuesday 28th January 00:15

Gary H 2008

3,507 posts

220 months

Tuesday 28th January 2014
quotequote all
Yup, they do hop smile

ears

ARAF

20,759 posts

254 months

Tuesday 28th January 2014
quotequote all
Gary H 2008 said:
Yup, they do hop smile

ears
laugh Guess I should have left that one for you from the start.

ringram

14,702 posts

279 months

Tuesday 28th January 2014
quotequote all
MyM8V8 said:
Can someone tell me if VXR8 shafts are the same as the previous models?

If so get the BMR unit for the driver side.
Im pretty sure they are different.
I just got one for the drivers side. $300 US from memory.
Whacked it in my suitcase biggrin

SturdyHSV

10,443 posts

198 months

Tuesday 28th January 2014
quotequote all
MyM8V8 said:
Can someone tell me if VXR8 shafts are the same as the previous models?

If so get the BMR unit for the driver side.

Edited by MyM8V8 on Tuesday 28th January 00:15
Has your BMR completely eliminated the hop?

On mine, it's now a lot smoother, no doubt about that, but it can still hop at times.

Based on my, erm, 'testing', it'll still happen if you don't give it enough beans to completely light the tyres up.

So for example at the Pod, drove around the burnout box, gave it a little jip just to spin them round a bit to scrub off any crap, and the surface was grippier than expected, so I got a serious amount of tramp.

Also, on the (private) road, if you're right on the edge of slipping and not, you can get some hop sometimes.

It doesn't bother me too much, the only instances I'm not a fan of is occasionally if I leave an empty junction and completely by accident apply too much throttle and end up embarrassingly sliding along the road a bit sideways, the actual wheels spinning process is velvet smooth, it's just when I finally remember in my blind panic to fully correct the skid and straighten it back out, there is sometimes a little rumble as it all grips back into a straight line. It's not a huge deal, there is just still some room for improvement to make it perfect...

Roger wasn't convinced there was enough difference in the diameters of the BMR unit vs. the stock one, it appears the clever git may have been right hehe

Burnouts on the other hand are absolutely fine and tramp free hehe

For reference, the car has a truetrac LSD, the monkfish rear end pack, harrop diff cover and upgraded dampers back there.

MyM8V8

9,468 posts

226 months

Tuesday 28th January 2014
quotequote all
SturdyHSV said:
MyM8V8 said:
Can someone tell me if VXR8 shafts are the same as the previous models?

If so get the BMR unit for the driver side.

Edited by MyM8V8 on Tuesday 28th January 00:15
Has your BMR completely eliminated the hop?

On mine, it's now a lot smoother, no doubt about that, but it can still hop at times.

Based on my, erm, 'testing', it'll still happen if you don't give it enough beans to completely light the tyres up.

So for example at the Pod, drove around the burnout box, gave it a little jip just to spin them round a bit to scrub off any crap, and the surface was grippier than expected, so I got a serious amount of tramp.

Also, on the (private) road, if you're right on the edge of slipping and not, you can get some hop sometimes.

It doesn't bother me too much, the only instances I'm not a fan of is occasionally if I leave an empty junction and completely by accident apply too much throttle and end up embarrassingly sliding along the road a bit sideways, the actual wheels spinning process is velvet smooth, it's just when I finally remember in my blind panic to fully correct the skid and straighten it back out, there is sometimes a little rumble as it all grips back into a straight line. It's not a huge deal, there is just still some room for improvement to make it perfect...

Roger wasn't convinced there was enough difference in the diameters of the BMR unit vs. the stock one, it appears the clever git may have been right hehe

Burnouts on the other hand are absolutely fine and tramp free hehe

For reference, the car has a truetrac LSD, the monkfish rear end pack, harrop diff cover and upgraded dampers back there.
Well its patently much better than two stock units paddling up the road! (And there's plenty of others who agree)

Your last problem is the rubber doughnuts on the prop which will wind up and cause hop. Got rid of one on the ute (better) and am about to order a prop with solid UJs both ends.

Edited by MyM8V8 on Tuesday 28th January 11:32

SturdyHSV

10,443 posts

198 months

Tuesday 28th January 2014
quotequote all
MyM8V8 said:
Well its patently much better than two stock units paddling up the road! (And there's plenty of others who agree)

Your last problem is the rubber doughnuts on the prop which will wind up and cause hop. Got rid of one on the ute (better) and am about to order a prop with solid UJs both ends.

Edited by MyM8V8 on Tuesday 28th January 11:32
So in effect the prop is waggling the diff around and causing the hop that way?

gsd2000

11,515 posts

214 months

Tuesday 28th January 2014
quotequote all
SturdyHSV said:
MyM8V8 said:
Well its patently much better than two stock units paddling up the road! (And there's plenty of others who agree)

Your last problem is the rubber doughnuts on the prop which will wind up and cause hop. Got rid of one on the ute (better) and am about to order a prop with solid UJs both ends.

Edited by MyM8V8 on Tuesday 28th January 11:32
So in effect the prop is waggling the diff around and causing the hop that way?
its a possibility

SturdyHSV

10,443 posts

198 months

Tuesday 28th January 2014
quotequote all
gsd2000 said:
its a possibility
Interesting scratchchin