Propellar / driveshaft wibrations
Propellar / driveshaft wibrations
Author
Discussion

omalley34male

Original Poster:

57 posts

153 months

Thursday 13th February 2014
quotequote all
Hi all speedjunkies
i have vibrations on the driveshaft between 80-120km/h and wonders how to solv them is it any use to fiddle with the original shaft or better of getting a new improved one but then again 1 or 2 piece ?
what do you guys use that works ?

English is NOT my primary language so i hope you can cope with my sentence and Spelling ;o)

MyM8V8

9,468 posts

226 months

Thursday 13th February 2014
quotequote all
How many kilometers has it done?

gsd2000

11,515 posts

214 months

Thursday 13th February 2014
quotequote all
I would fit check to make sure that it is nice and tight, then inspect all of the rubber mounts.

It could possibly be caused by the rubber in one of the mounts perishing, so check to make sure that they have no rips or tears in them and just look for any thing obvious

omalley34male

Original Poster:

57 posts

153 months

Friday 14th February 2014
quotequote all
Hi now i have about 140.000km on it just a Little curious looking what shaft there is and some say go 1 piece and other on forums says two pieces what are you guys have on yours ?

MyM8V8

9,468 posts

226 months

Friday 14th February 2014
quotequote all
omalley34male said:
Hi now i have about 140.000km on it just a Little curious looking what shaft there is and some say go 1 piece and other on forums says two pieces what are you guys have on yours ?
Prop should be OK. Maybe the problem is with the gearbox? Might be a good idea to check the gearbox mount and all the rear suspension and diff bushes. You could also check for wear in the prop shaft spigot bushes and maybe the centre bearing???

One piece prop OK up to 240kph, then will vibrate. Two piece seems to be the way to stay.

phantomf4

143 posts

180 months

Friday 14th February 2014
quotequote all
Hi, Spigot bearing at tail of gearbox or U/Joint at diff
Al

omalley34male

Original Poster:

57 posts

153 months

Wednesday 12th March 2014
quotequote all
ok i was thinking of changing the cross bearing dont know whats name it got in English knutkors in Swedish
is it a dana 50 cross?

SturdyHSV

10,443 posts

198 months

Wednesday 12th March 2014
quotequote all
MyM8V8 said:
One piece prop OK up to 240kph, then will vibrate. Two piece seems to be the way to stay.
Yikes, who found that out?

monkfish1

12,522 posts

255 months

Wednesday 12th March 2014
quotequote all
phantomf4 said:
Hi, Spigot bearing at tail of gearbox or U/Joint at diff
Al
This is the most likely.

mikeyb1987

2,358 posts

185 months

Wednesday 12th March 2014
quotequote all
monkfish1 said:
phantomf4 said:
Hi, Spigot bearing at tail of gearbox or U/Joint at diff
Al
This is the most likely.
Excuse the ignorance, but is that a different spigot bearing to the notorious one that is known to fail catastrophically?

What's the costs of replacing the tail bearing/universal joint at the diff?

monkfish1

12,522 posts

255 months

Wednesday 12th March 2014
quotequote all
mikeyb1987 said:
Excuse the ignorance, but is that a different spigot bearing to the notorious one that is known to fail catastrophically?

What's the costs of replacing the tail bearing/universal joint at the diff?
Yes. There is a spigot in the back of the tailshaft / front of the prop to keep them aligned. The rubber donut just transmits the drive. Said spigot is a little bronze sleeve that is rubber mounted. This and the rubber donut usually fail together.

mikeyb1987

2,358 posts

185 months

Wednesday 12th March 2014
quotequote all
monkfish1 said:
mikeyb1987 said:
Excuse the ignorance, but is that a different spigot bearing to the notorious one that is known to fail catastrophically?

What's the costs of replacing the tail bearing/universal joint at the diff?
Yes. There is a spigot in the back of the tailshaft / front of the prop to keep them aligned. The rubber donut just transmits the drive. Said spigot is a little bronze sleeve that is rubber mounted. This and the rubber donut usually fail together.
Ah, I see. Thanks for the clarification smile

stevieturbo

18,106 posts

278 months

Wednesday 12th March 2014
quotequote all
MyM8V8 said:
One piece prop OK up to 240kph, then will vibrate. Two piece seems to be the way to stay.
Depends on length, material, gearing etc.

But as has been covered before, it all boils down to the critical speed of the shaft.

With any 1 piece, this will be much lower than 2 smaller shafts.

Carbon fibre will extend this amount by a lot
Aluminium will extend this by a little over steel
Larger diameters will also extend this amount in any material.

And a taller diff ratio will slow the shaft down, also extending road speed vs shaft speed.

Given I dont trust aluminium, and carbon fibre is silly money...2 piece steel is the easiest solution.
Ive had mine at over 9000rpm with no issues.