Wortec Back Box Rattling
Wortec Back Box Rattling
Author
Discussion

Vxr8Girl

Original Poster:

207 posts

171 months

Saturday 15th February 2014
quotequote all
My mechanic believes it's the baffle inside the drivers side back box and tells me this isn't repairable frown

Dread to think how much a new Wortec back box will be, either that or I have to put up with this incessant rattling!

One thing after another with the car at the moment frown

ARAF

20,759 posts

254 months

Saturday 15th February 2014
quotequote all
Vxr8Girl said:
My mechanic believes it's the baffle inside the drivers side back box and tells me this isn't repairable frown

Dread to think how much a new Wortec back box will be, either that or I have to put up with this incessant rattling!

One thing after another with the car at the moment frown
Any warranty on the exhaust? Not sure about Wortec, but lots of stainless exhausts have a lifetime warrant.

pah250

3,270 posts

186 months

Saturday 15th February 2014
quotequote all
Do you have the switchable wortec?

One of my valves once started to rattle quite bad and it sounded aweful. The valves on the switchable wortec are right next to the back box. Monkfish/Wortec swapped the valve under warranty.

Vxr8Girl

Original Poster:

207 posts

171 months

Saturday 15th February 2014
quotequote all
I don't have a receipt for when the exhaust was purchased unfortunately so no warranty option frown

It is a switchable Wortec yes, I have tried switching it onto quiet mode to see if that changes the rattle, it's still there just a little quieter. Is there any way of finding out if it's definitely a switch issue?

Thanks smile

pah250

3,270 posts

186 months

Saturday 15th February 2014
quotequote all
Vxr8Girl said:
I don't have a receipt for when the exhaust was purchased unfortunately so no warranty option frown

It is a switchable Wortec yes, I have tried switching it onto quiet mode to see if that changes the rattle, it's still there just a little quieter. Is there any way of finding out if it's definitely a switch issue?

Thanks smile
Wortec will know when you purchased it (even if you did it through another dealer) as I believe they record the registration plate against the purchase. That said, my Wortec was out of warranty when I had my issues, but as I'd had so many problems with the valves they did it under warranty anyway.

Without removing the valve and putting in a blanking plate I don't know how you'll determine for sure if it's the box or the valve. Mine used to still rattle open or closed, so I left it open so that the rattle was less noticeable until it was fixed. My money is on the valve.

mik_ok

1,580 posts

272 months

Saturday 15th February 2014
quotequote all
And if it is a baffle, any SS Exhaust fabricator worth their salt will be able to open up the box, fix it and re-weld the box closed. About an hours labour I would guess.

ARAF

20,759 posts

254 months

Saturday 15th February 2014
quotequote all
mik_ok said:
And if it is a baffle, any SS Exhaust fabricator worth their salt will be able to open up the box, fix it and re-weld the box closed. About an hours labour I would guess.
This is true. smile There's too many places nowadays that want to replace rather than repair.

gsd2000

11,515 posts

214 months

Saturday 15th February 2014
quotequote all
If you cant get a replacement have a chat with craig at dynotorque. Hes an excellent fabricator and im fairly certain he knows how these boxes work internally so should be able to strip and sort the rattle out

wav8

3,926 posts

179 months

Saturday 15th February 2014
quotequote all
If its the valve and you are unable to source pm me got replacement ones for my last car that were not wortec.

neiljohnson

11,298 posts

238 months

Saturday 15th February 2014
quotequote all
Also check the bolts securing the valve I've seen them work loose

Vxr8Girl

Original Poster:

207 posts

171 months

Saturday 15th February 2014
quotequote all
Thanks for all of the replies smile

The exhaust was on when I bought the car so no idea how old it is, its got to be a good few years old looking at it plus I've owned the car for nearly 2 years now.

I haven't got a blanking plate to check to see if it is the valve causing the issue, can I just remove the switch and bolt the exhaust back up to test that theory?


S800VXR

5,877 posts

231 months

Sunday 16th February 2014
quotequote all
Vxr8Girl said:
Thanks for all of the replies smile

The exhaust was on when I bought the car so no idea how old it is, its got to be a good few years old looking at it plus I've owned the car for nearly 2 years now.

I haven't got a blanking plate to check to see if it is the valve causing the issue, can I just remove the switch and bolt the exhaust back up to test that theory?
No as removing the valve will leave a 20mm or so gap and the pipes aren't slack enough to pull up flush.

pah250

3,270 posts

186 months

Sunday 16th February 2014
quotequote all
S800VXR said:
Vxr8Girl said:
Thanks for all of the replies smile

The exhaust was on when I bought the car so no idea how old it is, its got to be a good few years old looking at it plus I've owned the car for nearly 2 years now.

I haven't got a blanking plate to check to see if it is the valve causing the issue, can I just remove the switch and bolt the exhaust back up to test that theory?
No as removing the valve will leave a 20mm or so gap and the pipes aren't slack enough to pull up flush.
But you could probably buy the blanking plates from monkfish. Doubt they will cost much.

R8OMG

176 posts

161 months

Sunday 16th February 2014
quotequote all
Would it not be possible to bolt the pipes together without the blanking plate accepting the fact that there will be a gap it will blow but it may be enough to stop them knocking against each other and secure them enough for a quick drive to see if the rattle has gone

snowwolf

11,503 posts

206 months

Sunday 16th February 2014
quotequote all
mik_ok said:
And if it is a baffle, any SS Exhaust fabricator worth their salt will be able to open up the box, fix it and re-weld the box closed. About an hours labour I would guess.
Mik is right, or even the nice guys at T&S engineering will do a great job,

Vxr8Girl

Original Poster:

207 posts

171 months

Sunday 16th February 2014
quotequote all
The rattle is noticeable at idle so I guess if I start it without the valve in place I'd have my answer.
I suppose a cheap alternative to a new switch would be a loud plate in place of the switch?

If it is the baffles I'll probably take it to Dynotorque in Brum as they are fairly close to me, thanks for that tip Gurm smile

monkfish1

12,522 posts

255 months

Tuesday 18th February 2014
quotequote all
99% its a valve.

If you want to prove it, give Andy a call and he can send you a blanking plate. Just remove valve and install plate, then check.

Vxr8Girl

Original Poster:

207 posts

171 months

Tuesday 18th February 2014
quotequote all
Ok smile It will have to wait until next week after pay day as I'm broke now lol.

preciousmetal

3,373 posts

207 months

Tuesday 18th February 2014
quotequote all
Vxr8Girl said:
Ok smile It will have to wait until next week after pay day as I'm broke now lol.
If its a slight metallic tinkling sound at idle its the valve, mine had the same - managed to get mine tightened up, now sorted smile

Vxr8Girl

Original Poster:

207 posts

171 months

Tuesday 18th February 2014
quotequote all
preciousmetal said:
If its a slight metallic tinkling sound at idle its the valve, mine had the same - managed to get mine tightened up, now sorted smile
Yes that's what it sounds a like! I'll have to try and tighten it up at the weekend, thanks for the tip smile