MAF or MafLess OTRCAI??
MAF or MafLess OTRCAI??
Author
Discussion

VXRocky

Original Poster:

262 posts

185 months

Tuesday 18th February 2014
quotequote all
Good morning Ladies and Gents,

This is very likely to be a daft question, however I'm currently unsure!

I'm looking at getting a OTRCAI shipped over from Aus, however I need to know whether I need MAF or MAFless intake??

The car is 06 'Ro vxr with a Wortec Cat-Back, the rest is standard. Once this is fitted I plan on getting it remapped then maybe go for headers down the line. With this is mind, what are your opinions?

From what I understand, the MAF limits the air intake, but gives more precise air readings for the air/fuel ratio. But MAFless is limitless therefore better if you're looking for big power gains with cams etc?

TIA,
Adam.

Edited by VXRocky on Tuesday 18th February 06:54

snowwolf

11,503 posts

206 months

Tuesday 18th February 2014
quotequote all
You will need to go for the MAF version unless of course you are going to go down the route of having mapped mafless which can be a little costly.

007 VXR

64,187 posts

218 months

Tuesday 18th February 2014
quotequote all
imho (which is not worth much) laugh
Wait until you have other bits done that require a remap?

KMud

2,924 posts

187 months

Tuesday 18th February 2014
quotequote all
You'll get a lot of opinions either way. I bought both pipes with my OTRCAI, and ran the OTRCAI with the MAF and no remap for quite a while before more mods got done.

SturdyHSV

10,443 posts

198 months

Tuesday 18th February 2014
quotequote all
You'll need the MAF version to get up and running when you receive it.

You won't need a remap with just the cat back and OTRCAI. Sure, there would be gains, but if you're going to get headers (which you will wink ) then once they're fitted get it mapped.

IMHO of course (did the same to mine, but in a different order) thumbup

VXRocky

Original Poster:

262 posts

185 months

Tuesday 18th February 2014
quotequote all
Thanks for you advice gents!

I've been running the Wortec with just the standard map for a little while anyway, a bit longer wont hurt right??

Headers may come after AP Brake kit!

ringram

14,702 posts

279 months

Tuesday 18th February 2014
quotequote all
Actually, not quite true. It will work without the maf plugged in no problem.
.. except it will fail into the low octane table.

5 min job to fix, if you want to go mafless and need the tune tweaked let me know.

ringram

14,702 posts

279 months

Tuesday 18th February 2014
quotequote all
Oh, dont forget to take care of the separate IAT sensor. Most mafless otrcai's come with them, but you will need to check.

VXRocky

Original Poster:

262 posts

185 months

Tuesday 18th February 2014
quotequote all
Ringram, slightly off topic...

When's the application closing date for the IT Solutions Architect role you posted about a little while back?

ringram

14,702 posts

279 months

Tuesday 18th February 2014
quotequote all
VXRocky said:
but gives more precise air readings for the air/fuel ratio.
Not true in absolute terms. But is true in so far that the OEM tune is not optimised for each vehicle's specific VE.

If you optimise the OEM tune, then they will be probably equivalent. Except mafless you have removed an airflow restriction as well as an intake tract design limitation in addition to a device which is limited to a max of around 400rwhp due to hard limits in airflow measurement.

In close to stock setups the MAF is good as it auto adjusts to mods as it directly measures the volume of air going into the engine. The IAT is still used to calculate mass along with rpm.

Maf also must have a laminar flow, hence the requirement to be in a straight piece of pipe away from the throttle, it also gets upset with cams as it measures flow both ways. So and decent sized cam setup will also have to be mafless.

Mafless requires a static map to be used (the VE table) with other inputs such as intake temp, engine rpm and manifold vacuum to calculate the final mass of air. This static table shows at each load and rpm the efficiency of the engine and varies with each change in mods. So if you mess stuff around a lot in theory you need to mess the tune around too.

Mafless is the only accurate method for FI setups due to the hard limits in airflow.

ringram

14,702 posts

279 months

Tuesday 18th February 2014
quotequote all
VXRocky said:
Ringram, slightly off topic...

When's the application closing date for the IT Solutions Architect role you posted about a little while back?
No closing date, we have been recruiting constantly for the last 10 years smile

SturdyHSV

10,443 posts

198 months

Tuesday 18th February 2014
quotequote all
ringram said:
No closing date, we have been recruiting constantly for the last 10 years smile
What, pray tell, is this role(s), any details?

VXRocky

Original Poster:

262 posts

185 months

Tuesday 18th February 2014
quotequote all
SturdyHSV said:
What, pray tell, is this role(s), any details?
See here...

wozzza

404 posts

162 months

Tuesday 18th February 2014
quotequote all
You can get a MAF / MAFless intake from duspeed so you can run it with the MAF in place then later on swap it out when you get to it being a restriction. Granted it's not quite as pretty with the slightly longer bit of rubber pipe.

However, the option is there which is good.

VXRocky

Original Poster:

262 posts

185 months

Tuesday 18th February 2014
quotequote all
wozzza said:
You can get a MAF / MAFless intake from duspeed so you can run it with the MAF in place then later on swap it out when you get to it being a restriction. Granted it's not quite as pretty with the slightly longer bit of rubber pipe.

However, the option is there which is good.
Sticking with the MAF, seems like the best bet for mow. Emailed you earlier wozza!