Roller rockers
Author
Discussion

neal1980

Original Poster:

2,585 posts

270 months

Saturday 1st March 2014
quotequote all
Are they worth it??

Looking at these

http://www.ebay.co.uk/itm/Chevy-LS1-Alloy-Roller-R...

Seem cheap if they give you a few extra BHP

MyM8V8

9,468 posts

226 months

Saturday 1st March 2014
quotequote all
They will not give you ANY extra bhp.

They look like Yella Terras, but if they are a chinese copy, they wouldn't be going anywhere near the valvetrain one of my motors.

Edited by MyM8V8 on Saturday 1st March 13:49

neal1980

Original Poster:

2,585 posts

270 months

Saturday 1st March 2014
quotequote all
That's not what I'm reading.

They look pretty though hehe

KMud

2,924 posts

187 months

Saturday 1st March 2014
quotequote all
Stock rockers with trunion upgrade IMO after reading a bajillion threads on this on ls1tech. Assuming you aren't running crazy lift.

Edited by KMud on Saturday 1st March 14:15

gsd2000

11,515 posts

214 months

Saturday 1st March 2014
quotequote all
Stock with trunion upgrade here

MyM8V8

9,468 posts

226 months

Saturday 1st March 2014
quotequote all
neal1980 said:
That's not what I'm reading.

They look pretty though hehe
I have yella terras and I'm damn sure they don't give any extra HP. You would use them to beef up the valve train after some HP mods to your motor. Consensus is that stock rockers are hard to beat and benefit from a trunion upgrade as G has said.

S800VXR

5,877 posts

231 months

Saturday 1st March 2014
quotequote all
After reading this thread I went and did some reading.... Looks like a worthwhile safety mod to swap out for upgraded rockers?

stevieturbo

18,106 posts

278 months

Saturday 1st March 2014
quotequote all
S800VXR said:
After reading this thread I went and did some reading.... Looks like a worthwhile safety mod to swap out for upgraded rockers?
Not so much.

Whilst I use YT's myself and havent had problems, the same cannot be said for all. Whether it was a bad batch for a few years or whether it's a more common problem, there have been a lot of failures.

For that reason alone I wouldnt buy another set. And those "Granatelli" look identical to YT's in every respect. They probably just change the packaging.

An awful lot of people do say just use the standard rockers with the trunion upgrade. Lots and lots, so it would seen an easy option.

If using more lift and you wanted roller rockers, then...fk knows lol.
Comp's designs have varied over the years, Some people seem to like Crane. Jesel always get good reviews although not sure if they offer cheaper sets.

Some aftermarket heads can be fussy about which rockers you use too

KMud

2,924 posts

187 months

Saturday 1st March 2014
quotequote all
S800VXR said:
After reading this thread I went and did some reading.... Looks like a worthwhile safety mod to swap out for upgraded rockers?
What are you worried about failing? The stock rockers don't really fail often from what I've read, but they are sub-optimal in terms of scrubbing the valve tips and applying side loads that do in bronze valve guides in aftermarket heads. The needle bearings on the stock rockers are a liability though, hence the trunion upgrade. I went for a light-ish valve-train (not as light as Gurmeet's Ti bits cry) with beehive springs. Many go for dual springs and roller rockers.

S800VXR

5,877 posts

231 months

Saturday 1st March 2014
quotequote all
I was reading and referring to either Trunion upgrades or just buying OEM ones already upgraded...

gsd2000

11,515 posts

214 months

Sunday 2nd March 2014
quotequote all
S800VXR said:
I was reading and referring to either Trunion upgrades or just buying OEM ones already upgraded...
Its a DIY job so it depends. If you want to save time buy them already upgraded