***BANG*** smoke errr help
Discussion
So after a casual drive to alton (seriously it was casual!)
Pull in to the Carpark. Full lock and ***BANG*** smoke pours out and as I get out the car powersteering fluid is everywhere.
So it looks like the top of the two crimped hoses by the rack has popped out of the crimp and the rubber hose is just loose.
So what's likely to be the damage? Rack shot or am I lucky maybe? What's caused the blow. Just a weakened hose failure?
Thoughts???? Thanks.
Pull in to the Carpark. Full lock and ***BANG*** smoke pours out and as I get out the car powersteering fluid is everywhere.
So it looks like the top of the two crimped hoses by the rack has popped out of the crimp and the rubber hose is just loose.
So what's likely to be the damage? Rack shot or am I lucky maybe? What's caused the blow. Just a weakened hose failure?
Thoughts???? Thanks.
Behold81 said:
So after a casual drive to alton (seriously it was casual!)
Pull in to the Carpark. Full lock and ***BANG*** smoke pours out and as I get out the car powersteering fluid is everywhere.
So it looks like the top of the two crimped hoses by the rack has popped out of the crimp and the rubber hose is just loose.
So what's likely to be the damage? Rack shot or am I lucky maybe? What's caused the blow. Just a weakened hose failure?
Thoughts???? Thanks.
Rack should be fine Pull in to the Carpark. Full lock and ***BANG*** smoke pours out and as I get out the car powersteering fluid is everywhere.
So it looks like the top of the two crimped hoses by the rack has popped out of the crimp and the rubber hose is just loose.
So what's likely to be the damage? Rack shot or am I lucky maybe? What's caused the blow. Just a weakened hose failure?
Thoughts???? Thanks.
As long as you didn't run the engine for too long after the pump should alright too
Thanks all I'm recovered home. Although took a bit of time for breakdown.
Car is at mates garage to go on the ramp on Monday. Before we loaded it we could see the pressure pipe popped. Question is was it likely to be just a hose/crimp failure or something else causing it.
Guess we need to check it over then clamp it up and run it.
The engine was killed as it blew. Only other running was to get it in the parking bay and on/off the lorry. But on off lorry we kept it straight.
Car is at mates garage to go on the ramp on Monday. Before we loaded it we could see the pressure pipe popped. Question is was it likely to be just a hose/crimp failure or something else causing it.
Guess we need to check it over then clamp it up and run it.
The engine was killed as it blew. Only other running was to get it in the parking bay and on/off the lorry. But on off lorry we kept it straight.
throwyourbike said:
My power steering cooler went with a bang this time last year. I noticed the smoke pouring out of the engine bay and shut the engine down immediately.
It had to be restarted to drive it onto the trailer but there was no damage to the pump or rack so i reckon you'll be fine.
Cool that's good to know!It had to be restarted to drive it onto the trailer but there was no damage to the pump or rack so i reckon you'll be fine.
Mine did something similar few months back, slightly different circs in that my metal cooler pipe broke and dumped all the fluid.
I wouldn't worry mate from what you say your rack and pump should be fine doesn't sound like they were ran dry assuming the rubber is not split or damaged just put new jubilee clips on and fill it up. Few turns lock to lock and top up again. If you need new hose I got some from driftworks.
I wouldn't worry mate from what you say your rack and pump should be fine doesn't sound like they were ran dry assuming the rubber is not split or damaged just put new jubilee clips on and fill it up. Few turns lock to lock and top up again. If you need new hose I got some from driftworks.
lastmin8264 said:
Mine did something similar few months back, slightly different circs in that my metal cooler pipe broke and dumped all the fluid.
I wouldn't worry mate from what you say your rack and pump should be fine doesn't sound like they were ran dry assuming the rubber is not split or damaged just put new jubilee clips on and fill it up. Few turns lock to lock and top up again. If you need new hose I got some from driftworks.
I thought the 2 pipes from the pump and back were high pressure hence there crimped as a jubilee would not work. The cooler is low pressure hence you can. I wouldn't worry mate from what you say your rack and pump should be fine doesn't sound like they were ran dry assuming the rubber is not split or damaged just put new jubilee clips on and fill it up. Few turns lock to lock and top up again. If you need new hose I got some from driftworks.
Anyone know for sure?
If it is the line from pump to rack and factory crimped, then it will be high pressure.
DO NOT attempt to bodge a repair here. It is very high pressure, and dont forget PAS fluid is very flammable.
You can see where that can go quite easily.
Whilst less ideal, you could simply bypass the rack, connecting the feed/return together. The pressure is created by the rack itself, so the pump will simply just recirculate fluid which would let you drive the car albeit with heavy steering.
Try and get to a power washer and wash any fluid away to eliminate the fire risk before going too far.
DO NOT attempt to bodge a repair here. It is very high pressure, and dont forget PAS fluid is very flammable.
You can see where that can go quite easily.
Whilst less ideal, you could simply bypass the rack, connecting the feed/return together. The pressure is created by the rack itself, so the pump will simply just recirculate fluid which would let you drive the car albeit with heavy steering.
Try and get to a power washer and wash any fluid away to eliminate the fire risk before going too far.
stevieturbo said:
If it is the line from pump to rack and factory crimped, then it will be high pressure.
DO NOT attempt to bodge a repair here. It is very high pressure, and dont forget PAS fluid is very flammable.
You can see where that can go quite easily.
Whilst less ideal, you could simply bypass the rack, connecting the feed/return together. The pressure is created by the rack itself, so the pump will simply just recirculate fluid which would let you drive the car albeit with heavy steering.
Try and get to a power washer and wash any fluid away to eliminate the fire risk before going too far.
It will get a clean it needs it now!!! DO NOT attempt to bodge a repair here. It is very high pressure, and dont forget PAS fluid is very flammable.
You can see where that can go quite easily.
Whilst less ideal, you could simply bypass the rack, connecting the feed/return together. The pressure is created by the rack itself, so the pump will simply just recirculate fluid which would let you drive the car albeit with heavy steering.
Try and get to a power washer and wash any fluid away to eliminate the fire risk before going too far.
Agree on the repair not going to botch it. Been around hydrolics in the past. Powerful stuff my issue is what's caused it to fail. Coincidence or my header making it all a bit hot down there?
I've used these guys before to re-hose the oil cooler
pipes on the C30SE engines, just take the hoses to them
and I'm sure they will sort you out. Not the cheapest solution,
but if you cant get hoses off shelf then it's an alternative...
They're only 5 mins from your house.
G & R Hydraulics & Pneumatics
Country: United Kingdom
Region: England
City: Basingstoke
Postal code
RG21 7QB
Address
Parker House, Goat Lane , RG21 7QB
Phones
01256 330 033
Faxes
01256 351 888
Sites
http://www.tom-parker.co.uk
pipes on the C30SE engines, just take the hoses to them
and I'm sure they will sort you out. Not the cheapest solution,
but if you cant get hoses off shelf then it's an alternative...
They're only 5 mins from your house.
G & R Hydraulics & Pneumatics
Country: United Kingdom
Region: England
City: Basingstoke
Postal code
RG21 7QB
Address
Parker House, Goat Lane , RG21 7QB
Phones
01256 330 033
Faxes
01256 351 888
Sites
http://www.tom-parker.co.uk
Behold81 said:
It will get a clean it needs it now!!!
Agree on the repair not going to botch it. Been around hydrolics in the past. Powerful stuff my issue is what's caused it to fail. Coincidence or my header making it all a bit hot down there?
It would be rare for a factory crimped hose to fail. They're usually pretty robust.Agree on the repair not going to botch it. Been around hydrolics in the past. Powerful stuff my issue is what's caused it to fail. Coincidence or my header making it all a bit hot down there?
Just how close is it to the header tubes ?
stevieturbo said:
It would be rare for a factory crimped hose to fail. They're usually pretty robust.
Just how close is it to the header tubes ?
The steering gater is close. Not melting though. I checked. The hose that blew is not that near IIRC. I could see it from the top of the engine bay easy enough as its roomy around there. Just how close is it to the header tubes ?
I'll try get a pic tomorrow if can.
My thought is the rack got hot or something like that and the weakest link blew, I had just driven 20 miles then stopped I a car park before it blew. Also was on full lock when it's most under pressure.
stevieturbo said:
Has the actual crimp failed, or the metal pipe broken ?
From what I saw under torch light it looked like the hose was all intact. You could see the crushed hose with a straight edge and the crimp looked open ended. Almost not crimped anymore. I'll get a photo tomorrow. Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff




