Air bag warning light.
Air bag warning light.
Author
Discussion

GEARJAMMER

Original Poster:

449 posts

170 months

Monday 10th March 2014
quotequote all
My Monaro has had the airbag warning light on ever since i took the seats out to dry the carpet after a water leak (which im still not convinced ive sorted), will that light being on cause it to fail its M.O.T and if so can it be re-set via the buttons in the car (like the service light) or does it involve a trip to Picadors, or can my local garage do it when he M.O.Ts it?

If it involves plugging a lappy into it where the er plug?

(Monaro LS2 VXR)

Thanks in advance.

Tattooboy

7,946 posts

209 months

Monday 10th March 2014
quotequote all
Believe you need a Tech2 to do the airbag light? I'm not sure if the run of the mill cheapy readers can do it?

Mr sturdy is your expert on air bag lights !! smile

The plug is in the drivers side foot well, just follow the steering column down and you will see it.

Wyld Stallyn

2,056 posts

159 months

Monday 10th March 2014
quotequote all
GEARJAMMER said:
My Monaro has had the airbag warning light on ever since i took the seats out to dry the carpet after a water leak (which im still not convinced ive sorted), will that light being on cause it to fail its M.O.T and if so can it be re-set via the buttons in the car (like the service light) or does it involve a trip to Picadors, or can my local garage do it when he M.O.Ts it?

If it involves plugging a lappy into it where the er plug?

(Monaro LS2 VXR)

Thanks in advance.
Comms Plug under dash below Steering Wheel

and Yep Loadsa New MOT regs including Airbag lights and Door open lights and all sorts of silly stuff rolleyes

Sorry, Dunno what it will take to reset it tho

SturdyHSV

10,443 posts

198 months

Monday 10th March 2014
quotequote all
Typically Tech2 is needed. If you're handy with a soldering iron and understand sending data out of a serial port, you can do it yourself though apparently (I've not tried it)

The americans are your friends on this, try the following:

http://www.ls1gto.com/forums/showthread.php?t=4603...

There's a command line tool written for setting all the cluster stuff (shift lights, shut down logos etc.) here:

http://www.ls1gto.com/forums/showthread.php?t=5170...
(This one is specific to the addition of airbag reset functionality)
http://www.ls1gto.com/forums/showthread.php?t=5665...

And some info on making the cable if the circuit diagram isn't much use:

http://www.ls1gto.com/forums/showthread.php?t=5798...

I haven't tried any of this, it's similar to what Ferret has done, but without a cluster to test it on, I'd exercise some caution...

Hope that helps hehe

VinceM

1,906 posts

169 months

Monday 10th March 2014
quotequote all
I had this issue when I changed my seats over. Neil has a very very good code reader/diag but needed an extra piece of software to sort it out.

neiljohnson

11,298 posts

238 months

Monday 10th March 2014
quotequote all
VinceM said:
I had this issue when I changed my seats over. Neil has a very very good code reader/diag but needed an extra piece of software to sort it out.
Took a fair bit of homework that one!! Got there eventually though biggrin

SturdyHSV

10,443 posts

198 months

Tuesday 11th March 2014
quotequote all
Monkfish were very accommodating to my many requests to read/reset the codes whilst I was sorting out the dummy loads for my seats, so if you're getting something done there, you could always ask nicely wink

MyM8V8

9,468 posts

226 months

Tuesday 11th March 2014
quotequote all
SturdyHSV said:
Monkfish were very accommodating to my many requests to read/reset the codes whilst I was sorting out the dummy loads for my seats, so if you're getting something done there, you could always ask nicely wink
Yes. I have the problem still with the ute (same as 05 VXR's)and must try to get it sorted sometime. MF did do the tech2 reading but the code wasn't explicit enough to help deduce the problem. Having said that it could be seat related.

SturdyHSV

10,443 posts

198 months

Tuesday 11th March 2014
quotequote all
MyM8V8 said:
Yes. I have the problem still with the ute (same as 05 VXR's)and must try to get it sorted sometime. MF did do the tech2 reading but the code wasn't explicit enough to help deduce the problem. Having said that it could be seat related.
Do you remember the code? Happy to look up the parameters that trigger it for you smile