LIFTER FAILURE & DAMAGED CAM
LIFTER FAILURE & DAMAGED CAM
Author
Discussion

trendkill

Original Poster:

42 posts

154 months

Saturday 15th March 2014
quotequote all
Hello.

I'm fairly new to the forum and also owning a HSV R8. For those who don't know it's a Wortec Carbon Edition which has an LS2 6.0 Harrop 122 supercharged engine fitted. Great fun! I've had a few issues from the start but this is by far the worst. Noticed a knocking / tapping noise coming from the engine which over a week or so got worse. I decided to stop driving the motor and find out what was wrong. Once the coil packs and rocker was removed (on the left side) I thought the problem was a suspect lifter. After a late night drive to Derby to collect a decent rocker (Thanks Gurmeet!) I got back to the workshop, fitted it and soon realised that the problem was more serious than I thought. I've not labelled everything up, bagged and tagged with quite a few pictures, this is where I'm at!

First image was taken as I started to change the rear supercharger belt, which has snapped. I manage to do this with the charger still in place. Seems fate that I'd end up having to take it off sooner or later!
|http://thumbsnap.com/pmm65n6N[/url]









The last image shows where the problem is. Looks like it's time to start getting a list together for a load of parts from the USA.

Any advice, comments, suggestions etc.. are very welcome.

Many thanks!

Bob

Edited by trendkill on Saturday 15th March 14:47

gsd2000

11,515 posts

214 months

Saturday 15th March 2014
quotequote all
Like I said earlier. New lifters, gaskets, cam, bolts and get it running again

Then build a spare engine biggrin

007 VXR

64,187 posts

218 months

Saturday 15th March 2014
quotequote all
Sorry to read this frown
What would make that happen ?

trendkill

Original Poster:

42 posts

154 months

Saturday 15th March 2014
quotequote all
gsd2000 said:
Like I said earlier. New lifters, gaskets, cam, bolts and get it running again

Then build a spare engine biggrin
That's going to be the plan. Unless someone has a nice supercharged LSX kicking about for sale wink

Still waiting for a reply from BTR in the states.....

trendkill

Original Poster:

42 posts

154 months

Saturday 15th March 2014
quotequote all
007 VXR said:
Sorry to read this frown
What would make that happen ?
No idea. I do give it some stick. Always check fluids, let it warm up first and cool down after being used though. Just bad luck I guess!

trendkill

Original Poster:

42 posts

154 months

Saturday 15th March 2014
quotequote all
The view from my desk. One sad looking motor!





badboyburt

2,043 posts

208 months

Saturday 15th March 2014
quotequote all
Wow bad luck, was it an OEM lifters that failed or uprated lifters (Yellow Terras) ?

Painfull to see it like that, hopefully its not off the road long.

ringram

14,702 posts

279 months

Saturday 15th March 2014
quotequote all
Welcome to my world. Maybe lack of ZDDP in modern oils has something to do with it.
But depending on the damage chunks might have gone through the engine.

It doesnt look too bad though, so new cam and lifters might be all you need. One wheel on my oem lifter crapped out ended up almost flat on one side.

Ideal time for a cam upgrade!

j666eds

642 posts

180 months

Saturday 15th March 2014
quotequote all
change the lifter trays too, there about $7 each.

gsd2000

11,515 posts

214 months

Saturday 15th March 2014
quotequote all
I thought that the ls2 came with uprated lifter trays

j666eds

642 posts

180 months

Saturday 15th March 2014
quotequote all
gsd2000 said:
I thought that the ls2 came with uprated lifter trays
They wear out apparently (what i read on other forums) When i replaced my lifters they were quite loose in the old trays but the new ones they were tight (didn't touch the cam until i pushed the push rod down)

ringram

14,702 posts

279 months

Saturday 15th March 2014
quotequote all
Or get lifters with tie bars..

trendkill

Original Poster:

42 posts

154 months

Monday 17th March 2014
quotequote all
I'm wondering whether to remove the engine or do the work with it still in the vehicle.

Shall do some digging and find out when the clutch was last done, this will be the decider I guess.

Lifters with tie bars seems like a good idea. I don't know a great deal about all the different parts I'm going to need.

Hopefully once the heads are off I'll have a better idea.

Many thanks and keep the comments coming!

Bob


trendkill

Original Poster:

42 posts

154 months

Monday 17th March 2014
quotequote all
Right hand side head is now off. Looks nice and clean! rolleyes


badboyburt

2,043 posts

208 months

Monday 17th March 2014
quotequote all
Christ thats some bad detonating.

New crate engine possibly, thats a lot of hard work you have ahead of you.

So sad to see and especially as you havent had it long.

Wish you luck whatever route you go down.

MadMaxHSV

1,816 posts

229 months

Monday 17th March 2014
quotequote all
badboyburt said:
Christ thats some bad detonating.
Nothing to do with det.
Coked pistons par for the course on a stock motor. PCV system burned a lot of oil on the Monaro LS2 setup. Don't think it was much changed on the VXR8...

Hurry up and get those trays out and pull the lifter. Fingers crossed the lifter bore is ok still.

badboyburt

2,043 posts

208 months

Monday 17th March 2014
quotequote all
MadMaxHSV said:
Nothing to do with det.
Coked pistons par for the course on a stock motor. PCV system burned a lot of oil on the Monaro LS2 setup. Don't think it was much changed on the VXR8...

Hurry up and get those trays out and pull the lifter. Fingers crossed the lifter bore is ok still.
Ive had my head off and it looked sod all like that, I changed gaskets as one showed signs of leaking and they where know wear near as bad as these.

monkfish1

12,522 posts

255 months

Monday 17th March 2014
quotequote all
badboyburt said:
Christ thats some bad detonating.
Where?

badboyburt

2,043 posts

208 months

Monday 17th March 2014
quotequote all
monkfish1 said:
badboyburt said:
Christ thats some bad detonating.
Where?
Obviously detontation was the wrong word but point being the top of my pistons where not that filthy (50k) why would they be so black ?


monkfish1

12,522 posts

255 months

Monday 17th March 2014
quotequote all
badboyburt said:
Obviously detontation was the wrong word but point being the top of my pistons where not that filthy (50k) why would they be so black ?
Looks pretty normal to me.