Is this better than a standard LS3 intake?
Is this better than a standard LS3 intake?
Author
Discussion

djwilk

Original Poster:

1,693 posts

200 months

Sunday 16th March 2014
quotequote all
As per the hyperlink:

http://www.ebay.com/itm/Tig-Welded-Fabricated-Alum...

Is there a benefit having one of these over the LS3 intake?

ARAF

20,759 posts

254 months

Sunday 16th March 2014
quotequote all
assault racing said:
They are about 3" taller than a stock polymer GM manifold, so make sure you have hood clearance!
Surely the first question should be "Do you have that clearance?"

gsd2000

11,515 posts

214 months

Sunday 16th March 2014
quotequote all
Just get a FAST 102

jameshsv

5,844 posts

191 months

Sunday 16th March 2014
quotequote all
gsd2000 said:
Just get a FAST 102
I agree with Gsd2ooo but expensive

djwilk

Original Poster:

1,693 posts

200 months

Sunday 16th March 2014
quotequote all
I know it is 3 inches taller and I would very much hope it can fit under the boonet of the vxr8, no?

I imagine either this or the FAsT intake increase the flow into the cylinder heads, but then would heads need upgrading to take advantage of the improved flow in the intake?

jameshsv

5,844 posts

191 months

Sunday 16th March 2014
quotequote all
djwilk said:
I know it is 3 inches taller and I would very much hope it can fit under the boonet of the vxr8, no?

I imagine either this or the FAsT intake increase the flow into the cylinder heads, but then would heads need upgrading to take advantage of the improved flow in the intake?
Ls3 heads flow ok.I have 243 cnc ported heads and fast 102 with matching TB and works well.

stevieturbo

18,106 posts

278 months

Sunday 16th March 2014
quotequote all
I think some posted photos of that on one of the US forums.

As with most cheap chinese stuff, they look ok on the outside....but fall down badly inside.

It's cheap for a reason

SturdyHSV

10,443 posts

198 months

Sunday 16th March 2014
quotequote all
The ls3 is a reasonable intake stock. Going to a 102, you may not see big gains for the money, but if you're going to do heads/cam later, the gains will be greater, the 102 can take whatever you throw at it by most accounts...

djwilk

Original Poster:

1,693 posts

200 months

Sunday 16th March 2014
quotequote all
SturdyHSV said:
The ls3 is a reasonable intake stock. Going to a 102, you may not see big gains for the money, but if you're going to do heads/cam later, the gains will be greater, the 102 can take whatever you throw at it by most accounts...
The plan is to throw a cam that is sizeable, but avoiding it being undriveable in town. I have so far learnt that the ASA Cam is out of question. The last dyno read at SRR showed 490bhp with stock engine, remap, OTR cai, WP 2.5 decat, stock headers.
The target is to get a reliable 550bhp. I know heads can be either ported or upgraded with something else. If I were to do the heads, then I guess buying is cheaper than porting, right? Yet again, I would not do anything about the heads, if there is no gain to be had at the power levels I am trying to achieve.

What would be nice, is a fairly flat torque and max power moved down the rev range.

ringram

14,702 posts

279 months

Sunday 16th March 2014
quotequote all
djwilk said:
The plan is to throw a cam that is sizeable, but avoiding it being undriveable in town. I have so far learnt that the ASA Cam is out of question. The last dyno read at SRR showed 490bhp with stock engine, remap, OTR cai, WP 2.5 decat, stock headers.
The target is to get a reliable 550bhp. I know heads can be either ported or upgraded with something else. If I were to do the heads, then I guess buying is cheaper than porting, right? Yet again, I would not do anything about the heads, if there is no gain to be had at the power levels I am trying to achieve.

What would be nice, is a fairly flat torque and max power moved down the rev range.
What was the actual rwhp number? Not the made up one, thats no use.
Cam only will get you where you are going. But you will need to look at your intake and log MAP at WOT. The otrcai might struggle.
Stock headers wont help either.

If you are looking at heads look at the tfs 255's £1500 for a pair. Fast 102 will give you some more if you need it though Id do that last IMO.
Cam first, log and check MAP, then address airbox, log and check dyno etc.

(ie) Go for the biggest bottleneck first. The cam.

djwilk

Original Poster:

1,693 posts

200 months

Sunday 16th March 2014
quotequote all
ringram said:
What was the actual rwhp number? Not the made up one, thats no use.
Cam only will get you where you are going. But you will need to look at your intake and log MAP at WOT. The otrcai might struggle.
Stock headers wont help either.

If you are looking at heads look at the tfs 255's £1500 for a pair. Fast 102 will give you some more if you need it though Id do that last IMO.
Cam first, log and check MAP, then address airbox, log and check dyno etc.

(ie) Go for the biggest bottleneck first. The cam.
From memory, it was something like 386rwhp. The OTRCAI is by Orrsom.
Headers are on the to do list as well. How about those headers that come with a crate engine? Are they improved over the stock LS3 headers?
Also, would I see a benefit in changing the exhaust to 3inch throughout?

ringram

14,702 posts

279 months

Sunday 16th March 2014
quotequote all
According to Mr Vizard dual 2.5 will support around 535fwhp without loss. So you might lose a tad, but probably not enough to warrant an expensive exhaust setup.
Dual 3" is good for over 700fwhp zero (or near to it) loss
Even a stock LS1 gains most from 1-7/8 headers at max rpm.

If it were me, Id do cam, them probably headers. Though it depends on what sort of power curve you want.

If you want max low rpm torque Id look at a smaller duration cam, heads and airbox. Because the stock exhaust wont worry you too much until the rpm gets higher.

Higher rpm power, then larger cam, headers and airbox. Maybe the Fast if you want all you can get. Then add heads if you dont hit your target.

For an LS3 cam Id probably do a comp LXL 222/234-114+4 which is just over 0.600 lift as a mild-ish NA cam. Which is bang on zero overlap.
Or a 218/230-114+4 if you want super mild.

Heads are free from compromise power, but arnt cheap. A decent airbox isnt too pricey for what you can gain. But you need to log your existing one and see if you are restricted.


djwilk

Original Poster:

1,693 posts

200 months

Monday 17th March 2014
quotequote all
ringram said:
According to Mr Vizard dual 2.5 will support around 535fwhp without loss. So you might lose a tad, but probably not enough to warrant an expensive exhaust setup.
Dual 3" is good for over 700fwhp zero (or near to it) loss
Even a stock LS1 gains most from 1-7/8 headers at max rpm.

If it were me, Id do cam, them probably headers. Though it depends on what sort of power curve you want.

If you want max low rpm torque Id look at a smaller duration cam, heads and airbox. Because the stock exhaust wont worry you too much until the rpm gets higher.

Higher rpm power, then larger cam, headers and airbox. Maybe the Fast if you want all you can get. Then add heads if you dont hit your target.

For an LS3 cam Id probably do a comp LXL 222/234-114+4 which is just over 0.600 lift as a mild-ish NA cam. Which is bang on zero overlap.
Or a 218/230-114+4 if you want super mild.

Heads are free from compromise power, but arnt cheap. A decent airbox isnt too pricey for what you can gain. But you need to log your existing one and see if you are restricted.
Piece of really good advice mate, so thanks. I am trying to plan for the whole operation, as the engine will be on the table soon and good to be tampered with. I would prefer to do as much as possible whilst it's out of the bay, hence my endless questions. I am quite surprised the Orrsom OTRCAI could be a bottleneck here, but hey! Would you advise a proper K&N cone?

As for the CAM, I would very much prefer something that is quite sharp, but not ASA sharp, something that will allow me idle and drive in traffic still... I have read somewhere that advancing timing could result in better low down torque at the cost of peak power. Also, as far as I understand what LSA means, what is the "+4" bit?

ringram

14,702 posts

279 months

Monday 17th March 2014
quotequote all
Actually the +4 is the advance, you can rotate it back more for better higher rpm peak.
Both were +4 as I like low end torque smile

The LSA determines overlap and scavanging, which you want NA to help fill the cylinder. But those 2 cams are mild with zero or less overlap at 0.050 valve lift. You can close LSA down for more overlap and more of a cam sound, keep duration short for lower rpm power. Though the LS3 type heads dont like as much overlap due to the large intake valves.

So you could go with 112 LSA on the larger cam and then you will have a tad of +ve overlap, not much mind. Do a bit of reading on LS3 cams, you will find the recommendation is less overlap than LS1/2 cams.

This is what you need to read http://www.gmhightechperformance.com/tech/lsx_engi...