Grrr gearbox ro6.0
Discussion
S60hsv
Original Poster
86 posts
[report] [news] 22:25
Ok so this gearbox is really pissin me off sometimes strugle to get it in reverse and 1st should I be worryied o and went for a drive before and put from second to 3rd and the clutch didn't feal like it came up all the way felt like it went up 90 percent but not the whole way so pushed clutch all the way in selected neutral and then 3rd again and it seemed fine should I be worried ?
Original Poster
86 posts
[report] [news] 22:25
Ok so this gearbox is really pissin me off sometimes strugle to get it in reverse and 1st should I be worryied o and went for a drive before and put from second to 3rd and the clutch didn't feal like it came up all the way felt like it went up 90 percent but not the whole way so pushed clutch all the way in selected neutral and then 3rd again and it seemed fine should I be worried ?
S60hsv said:
S60hsv
Original Poster
86 posts
[report] [news] 22:25
Ok so this gearbox is really pissin me off sometimes strugle to get it in reverse and 1st should I be worryied o and went for a drive before and put from second to 3rd and the clutch didn't feal like it came up all the way felt like it went up 90 percent but not the whole way so pushed clutch all the way in selected neutral and then 3rd again and it seemed fine should I be worried ?
Change the spigot bearing.Original Poster
86 posts
[report] [news] 22:25
Ok so this gearbox is really pissin me off sometimes strugle to get it in reverse and 1st should I be worryied o and went for a drive before and put from second to 3rd and the clutch didn't feal like it came up all the way felt like it went up 90 percent but not the whole way so pushed clutch all the way in selected neutral and then 3rd again and it seemed fine should I be worried ?
Change the clutch fluid if it's black that'll need changing too.
Make sure you get a remote clutch bled line fitted when the box is out
.What clutch do you have - I upgraded mine to LS7 as this is a common problem with the standard clutch if you are pushing it through the gears (lots of posts on the subject - look on Facebook for pictures on MW Performance site for my new one). Changing fluid might give temporary relief. Get the clutch upgraded, add a remote bleed - and get spigot done at same time if it is the common problem - or don't push it so hard!
Marc did mine and a fantastic job he did too - oh ... and check out slave.
Welcome to the Monaro owner's club!
;-)
Ian
Marc did mine and a fantastic job he did too - oh ... and check out slave.
Welcome to the Monaro owner's club!
;-)
Ian
S60hsv said:
Guseing standard one not to sure how much does this spig bearing cost fitted ruff idea
Gear box out job .....and change the slave cylinder at the same time 
If standard with that power you need a better clutch at least an LS7, BUT if you want more power, LS7 will not be any good. So more money.. ACT is good for around £1200+fitting
Edited by 007 VXR on Sunday 16th March 23:12
007 VXR said:
Gear box out job .....and change the slave cylinder at the same time 
If standard with that power you need a better clutch at least an LS7, BUT if you want more power, LS7 will not be any good. So more money.. ACT is good for around £1200+fitting
This probably stupid but if I get the twin act clutch fitted without the geRbox strengthened won't it put more stress on the trans and quite quickly get damaged ? 
If standard with that power you need a better clutch at least an LS7, BUT if you want more power, LS7 will not be any good. So more money.. ACT is good for around £1200+fitting
Edited by 007 VXR on Sunday 16th March 23:12
007 VXR said:
S60hsv said:
Guseing standard one not to sure how much does this spig bearing cost fitted ruff idea
Gear box out job .....and change the slave cylinder at the same time 
If standard with that power you need a better clutch at least an LS7, BUT if you want more power, LS7 will not be any good. So more money.. ACT is good for around £1200+fitting
Edited by 007 VXR on Sunday 16th March 23:12
) to mine.Definately Worth adding a remote bleed line (circa 45£) and having the rubber gaiter fitted as yours is likely to be as shot as mine was (circa 50 notes)
Just remember this is a rear wheel drive clutch not an expensive front wheel drive or awd clutch change money! 
A fwd clutch can be 6 hours labour (or more) compared to 3 or less hours on a rwd motor!
My LS7 clutch was cheaper to buy and fit than my Peugeot 406 clutch change or my Tourneo Flywheel and clutch change was!

A fwd clutch can be 6 hours labour (or more) compared to 3 or less hours on a rwd motor!

My LS7 clutch was cheaper to buy and fit than my Peugeot 406 clutch change or my Tourneo Flywheel and clutch change was!
S60hsv said:
007 VXR said:
Gear box out job .....and change the slave cylinder at the same time 
If standard with that power you need a better clutch at least an LS7, BUT if you want more power, LS7 will not be any good. So more money.. ACT is good for around £1200+fitting
This probably stupid but if I get the twin act clutch fitted without the geRbox strengthened won't it put more stress on the trans and quite quickly get damaged ? 
If standard with that power you need a better clutch at least an LS7, BUT if you want more power, LS7 will not be any good. So more money.. ACT is good for around £1200+fitting
Edited by 007 VXR on Sunday 16th March 23:12
BigbadVXR said:
Just remember this is a rear wheel drive clutch not an expensive front wheel drive or awd clutch change money! 
A fwd clutch can be 6 hours labour (or more) compared to 3 or less hours on a rwd motor!
My LS7 clutch was cheaper to buy and fit than my Peugeot 406 clutch change or my Tourneo Flywheel and clutch change was!
That would be about right and roughly what I paid for mine at MW 'HSV'. Have a look here ...
A fwd clutch can be 6 hours labour (or more) compared to 3 or less hours on a rwd motor!

My LS7 clutch was cheaper to buy and fit than my Peugeot 406 clutch change or my Tourneo Flywheel and clutch change was!
https://www.facebook.com/photo.php?fbid=6670682466...
None of the above is likely to fix it.
Its a known issue with the T56 model. If you look at what changed in the TR6060 you will see a number of issues were addressed, including synchro's to make shifting better etc.
Thats where the real issue is.
One tip is to select another forward gear, then snatch reverse and also double clutching.
If you force it you mess the synchro's up more.
My 2p
Its a known issue with the T56 model. If you look at what changed in the TR6060 you will see a number of issues were addressed, including synchro's to make shifting better etc.
Thats where the real issue is.
One tip is to select another forward gear, then snatch reverse and also double clutching.
If you force it you mess the synchro's up more.
My 2p
This is worth a watch (even just for how this guy can row a gearbox!)
http://www.youtube.com/watch?v=gBbsy0LjUvE
LS7 clutch is a delight to use after the stock one, I have complete faith in it.
The gearbox can be a bit of a pig, just try to rev match every shift as best you can, both down and up. When going up, due to the fairly slow rate it loses rpm, this may simply mean the shift has to take a little longer than you would like.
http://www.youtube.com/watch?v=gBbsy0LjUvE
LS7 clutch is a delight to use after the stock one, I have complete faith in it.
The gearbox can be a bit of a pig, just try to rev match every shift as best you can, both down and up. When going up, due to the fairly slow rate it loses rpm, this may simply mean the shift has to take a little longer than you would like.
ringram said:
None of the above is likely to fix it.
Its a known issue with the T56 model. If you look at what changed in the TR6060 you will see a number of issues were addressed, including synchro's to make shifting better etc.
Thats where the real issue is.
One tip is to select another forward gear, then snatch reverse and also double clutching.
If you force it you mess the synchro's up more.
My 2p
Good point Richard - I was more concerned with my clutch pedal not coming back up. Fitting the LS7 cured that and it drives a treat now. (and I recently took it for a very lively session - no problems at all).Its a known issue with the T56 model. If you look at what changed in the TR6060 you will see a number of issues were addressed, including synchro's to make shifting better etc.
Thats where the real issue is.
One tip is to select another forward gear, then snatch reverse and also double clutching.
If you force it you mess the synchro's up more.
My 2p
It's very true though - you have to add a little 'pause' between gear changes in my experience.
Regards
Ian
SturdyHSV said:
This is worth a watch (even just for how this guy can row a gearbox!)
http://www.youtube.com/watch?v=gBbsy0LjUvE
e.
That's a good find.http://www.youtube.com/watch?v=gBbsy0LjUvE
e.
I wouldn't dare drive mine like that, one handed it would have me in a ditch.
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff


