Powersteering again. I'm paranoid!
Powersteering again. I'm paranoid!
Author
Discussion

Behold81

Original Poster:

2,931 posts

200 months

Friday 28th March 2014
quotequote all
Before the PAS blew on me there was a small rattle/knock on the car. After the pipe was replaced the garage looked at it and believe the sound is the headers once they expand hitting my chassis rail where it was repaired/strengthened making it a bit thicker than normal.

Is there a way to prove this? The sound almost sounds bearing like. or shot bearing like. Its certainly rev dependent and takes 3-5 mins before it sounds. it also disappears at times too.

I'm a bit paranoid that its a sound from the rack where its shot. not sure if you would get a sound like that.

At the moment if it is the headers I need the chassis rail repairing again to remove the thickness on that side. that's not looking like it will be an easy job as there headers are close there.

any thoughts/tests would be appreciated.

thanks

TimDaciaBumdart

22,454 posts

241 months

Friday 28th March 2014
quotequote all
if it is the headers then you have two options

1.) Bash the ferk out of them to make them no longer foul
2.) Ditch the long tubes and go with stubbies, in the long run, its the better option unless you want that small amount of unnoticable power they give

KMud

2,924 posts

187 months

Friday 28th March 2014
quotequote all
Whack some fresh paint on the chassis rail and see if it gets marked and transfers onto the headers?

SturdyHSV

10,443 posts

198 months

Friday 28th March 2014
quotequote all
KMud said:
Whack some fresh paint on the chassis rail and see if it gets marked and transfers onto the headers?
Or blue tack wink

KMud

2,924 posts

187 months

Friday 28th March 2014
quotequote all
Wouldn't blu tack get sweaty and drop off?

SturdyHSV

10,443 posts

198 months

Friday 28th March 2014
quotequote all
KMud said:
Wouldn't blu tack get sweaty and drop off?
No idea, was just a funny idea or using blutack to fix things hehe

Tattooboy

7,946 posts

209 months

Friday 28th March 2014
quotequote all
Is there enough room to wrap some exhaust tape just on that part, see if the noise lessens?

ARAF

20,759 posts

254 months

Friday 28th March 2014
quotequote all
KMud said:
Wouldn't blu tack get sweaty and drop off?
I wish DaciaBumdart would get sweaty and drop off sometimes. hehe


If the headers are hitting the chassis, they should be wearing a patch shiny on the headers and the rail, where they are hitting. If there's no mark, I cannot see this as being the problem.

TheLeatherman

322 posts

196 months

Friday 28th March 2014
quotequote all
I have 2 inch DF 4-1 headers on mine and they don't touch!!! What brand and who fitted them is the first question......

Behold81

Original Poster:

2,931 posts

200 months

Friday 28th March 2014
quotequote all
TheLeatherman said:
I have 2 inch DF 4-1 headers on mine and they don't touch!!! What brand and who fitted them is the first question......
They wouldn't touch if I had not had a repair on the chassis rail. but the repair was not for strength not just patching so a complete new plate was put in over the length while minimising how much of the original was removed. it means that its a bit thicker there.

The headers are ProFlow which I believe are a stainless replica of the pacemakers. They fit fine everywhere else. There is a mark on the chassis rail so it is hitting but the sound just doesn't match up. I want to see if I can change the sound and if so i'll know its them making that sound. So I think the exhaust wrap is an idea. anyone got some off cuts laying around?

personally the sound is more a failing bearing or something. I need to run it with me under the car and wedge something in there and see if the sound changes.

Would the rack be able to make a sound like this???

As to who fit them. a local garage to me. I know the guy well and he is competent. he just is really busy at the moment and looking at it in detail is just not an option at the moment. and he has seen my car for to many days with intercooler mockups, clutches, headers, PAS pipes. Unlike monkfish its a small garage and carpark.





Edited by Behold81 on Friday 28th March 14:59


Edited by Behold81 on Friday 28th March 15:01

Behold81

Original Poster:

2,931 posts

200 months

Friday 28th March 2014
quotequote all
TimDaciaBumdart said:
if it is the headers then you have two options

1.) Bash the ferk out of them to make them no longer foul
2.) Ditch the long tubes and go with stubbies, in the long run, its the better option unless you want that small amount of unnoticable power they give
With my plans the extra flow will be needed long term.

Behold81

Original Poster:

2,931 posts

200 months

Friday 28th March 2014
quotequote all
SturdyHSV said:
Or blue tack wink
Why not duct tape???


gsd2000

11,515 posts

214 months

Friday 28th March 2014
quotequote all
Stiffer engine mounts

stevieturbo

18,105 posts

278 months

Friday 28th March 2014
quotequote all
Take the headers off and run the engine, see if it makes the noise smile

TimDaciaBumdart

22,454 posts

241 months

Friday 28th March 2014
quotequote all
stevieturbo said:
Take the headers off and run the engine, see if it makes the noise smile
/end thread!

rich24v

352 posts

240 months

Friday 28th March 2014
quotequote all
Ant,
You know where a car lift is, I also have a comprehensive "Clarkson" tool kit. smile

Behold81

Original Poster:

2,931 posts

200 months

Friday 28th March 2014
quotequote all
TimDaciaBumdart said:
stevieturbo said:
Take the headers off and run the engine, see if it makes the noise smile
/end thread!
PMSL

Behold81

Original Poster:

2,931 posts

200 months

Friday 28th March 2014
quotequote all
gsd2000 said:
Stiffer engine mounts
There stock but new engine mounts. Which are stiffer as my SC doesn't hit the strut anymore!!

Behold81

Original Poster:

2,931 posts

200 months

Friday 28th March 2014
quotequote all
rich24v said:
Ant,
You know where a car lift is, I also have a comprehensive "Clarkson" tool kit. smile
Might be over in a week or so!