Probably a good question for Ringram and all of the NA guys
Probably a good question for Ringram and all of the NA guys
Author
Discussion

djwilk

Original Poster:

1,693 posts

200 months

Tuesday 1st April 2014
quotequote all
Hi,
As some of you may know my engine exploded. Long story short I think I might be choosing a recon route.
More details about that once I have finalised, but I need to know what engine parts I need to get. I have got a list in mind, but checking if I have not forgotten anything. Assume I have complete con rods with pistons, crank and block. Then bare heads and just valves and rockers and covers. Oh and the deck plate with complete intake manifold coil packs and fuel rails. Ancilaries are a separate matter.

Also, one of the suppliers suggests I can have a custom made cam by comp cams. My goal is about 550 fly. Ideally, accessible at lower than engine-blowing RPM. Torque as well. No reboring, stroking, S/C etc. Keeping it simple. Anyone to advise what cam spec I would want to have it still streetable? Emissions not important.

Thanks.
Bart

jameshsv

5,844 posts

191 months

Tuesday 1st April 2014
quotequote all
Thought it was cheaper to go crate ls3 and sell off your parts.!

djwilk

Original Poster:

1,693 posts

200 months

Tuesday 1st April 2014
quotequote all
It is not, sadly...

I might be getting a new block with a used crank and pistons for a third of a cost of a new complete engine.

S800VXR

5,877 posts

231 months

Tuesday 1st April 2014
quotequote all
YHM

jameshsv

5,844 posts

191 months

Tuesday 1st April 2014
quotequote all
djwilk said:
It is not, sadly...

I might be getting a new block with a used crank and pistons for a third of a cost of a new complete engine.
OK I hope it all comes together for yousmile

KMud

2,924 posts

187 months

Tuesday 1st April 2014
quotequote all
Most cams are comp cams, but I think many people on this forum have cam motion cams (likely through Pat Guerra/EPS) - they're meant to be more gentle on the valve-train. EPS tend to be quite slow to deliver mind.

djwilk

Original Poster:

1,693 posts

200 months

Tuesday 1st April 2014
quotequote all
KMud said:
Most cams are comp cams, but I think many people on this forum have cam motion cams (likely through Pat Guerra/EPS) - they're meant to be more gentle on the valve-train. EPS tend to be quite slow to deliver mind.
I've got till the end of Summer;)
What spec CAM would be good for street and easy on the valvetrain then and what gains to expect once fully fitted and tuned? Current decat catback otrcai made 490bhp.

gsd2000

11,515 posts

214 months

Tuesday 1st April 2014
quotequote all
Have a chat with brian tooley at brian tooley racing or patG, EPS, tickshift performance

Something like gareths cam would work well

TheLeatherman

322 posts

196 months

Tuesday 1st April 2014
quotequote all
Mandatory will be ARP rod bolts and double row timing chain. Not sure if it will pass emissions, but a Comp 224/228 was always a favourite street cam in Oz, but better still is the 232/234. Decent mafless tune on that, FAST intake, 90mm TB, OTR, maybe some lighter rockers, 1 & 7/8 4-1's and you should be doing some nice numbers - on a manual that should be making around 295 rwkw. Oh and get some decent springs on the valvetrain as they will help no end, but don't get the heavy dual springs.

And all fairly straightforward on the parts side in truth.

Edited by TheLeatherman on Tuesday 1st April 22:20

ArnieVXR

2,458 posts

214 months

Tuesday 1st April 2014
quotequote all
Can't see you achieving 550fwhp normally aspirated without a decent sized stroker kit or an unusable tune/cam.

I've just commissioned the build of my 4.100" stroked LS2. It will end up 6.7-litres, so should run over 500fwhp with a streetable cam, my FAST 102 and a bit of head work. That's where you need to be heading to achieve your goal.

djwilk

Original Poster:

1,693 posts

200 months

Tuesday 1st April 2014
quotequote all
I am only going by r8black's recent result of around 550 fwhp, hence my goal that was supposedly somewhat realistic, no?

ArnieVXR

2,458 posts

214 months

Tuesday 1st April 2014
quotequote all
mikeyb1987 just made 495-fwhp out of a stock stroke LS2 with LS3 heads, etc. That was impressive.

R8black made 460rwhp with a Cam, etc. I don't see that equates to 550fwhp. Indeed, I'd love to see any LS engine actually acquire well over a 100fwhp with a cam, etc and remain street legal (or even driveable).

Think about it this way, an LSX454 is rated at 580fwhp on fuel injection with a reasonable tune. That's a 7.4-litre motor.

stevieturbo

18,105 posts

278 months

Tuesday 1st April 2014
quotequote all
If you want low rpm performance n/a, go big on capacity.

You can do all the cams/heads in the world, but the extra engine size will make the biggest difference.

Also sent email via PH about some LS2 based parts.

Although not sure if you're LS2 or LS3 block/bore.

djwilk

Original Poster:

1,693 posts

200 months

Tuesday 1st April 2014
quotequote all
Stevie, thanks for the PM, it is an LS3, nevertheless...

Arnie, I appreciate what you are saying, I honestly thought I read 560 fly, but I might be wrong. Still, 460 rwhp is still a bloody good result and another 70 rwhp over my recent results. I also know that nothing can beat the displacement at the same time, but everywhere I read about a stroker, it sounds like a bad idea...

MyM8V8

9,468 posts

226 months

Tuesday 1st April 2014
quotequote all
djwilk said:
I've got till the end of Summer;)
What spec CAM would be good for street and easy on the valvetrain then and what gains to expect once fully fitted and tuned? Current decat catback otrcai made 490bhp.
I think Kaw has a brand new custom designed cam motions 222-230 cam to sell with sensible lift and lobes. Would be ideal for you. Add a set of 918 beehive springs and a set of Cadillac race lifters if you have to over rev it.


Edited by MyM8V8 on Tuesday 1st April 23:43

djwilk

Original Poster:

1,693 posts

200 months

Tuesday 1st April 2014
quotequote all
MyM8V8 said:
I think Kaw has a brand new custom designed cam motions 222-230 cam to sell with sensible lift and lobes. Would be ideal for you.
Sounds like I need to PM him wink Thanks smile

MyM8V8

9,468 posts

226 months

Tuesday 1st April 2014
quotequote all
djwilk said:
MyM8V8 said:
I think Kaw has a brand new custom designed cam motions 222-230 cam to sell with sensible lift and lobes. Would be ideal for you.
Sounds like I need to PM him wink Thanks smile
I think GSD has an unused double row chain if you must use one. The Katech C5R single row race item is highly rated and not too much dough and will stand up to the abuse you're going to give it. wink

djwilk

Original Poster:

1,693 posts

200 months

Wednesday 2nd April 2014
quotequote all
MyM8V8 said:
I think GSD has an unused double row chain if you must use one. The Katech C5R single row race item is highly rated and not too much dough and will stand up to the abuse you're going to give it. wink
Will email Gurmeet as well wink I'm assuming it is wise to bin the current timing kit and buy new when everything is on the table, right? Would I really need a C5R? Sounds a bit much for a not so shiny bling wink

MyM8V8

9,468 posts

226 months

Wednesday 2nd April 2014
quotequote all
djwilk said:
MyM8V8 said:
I think GSD has an unused double row chain if you must use one. The Katech C5R single row race item is highly rated and not too much dough and will stand up to the abuse you're going to give it. wink
Will email Gurmeet as well wink I'm assuming it is wise to bin the current timing kit and buy new when everything is on the table, right? Would I really need a C5R? Sounds a bit much for a not so shiny bling wink
Personally, if I were rebuilding a blown motor, I wouldn't re-use anything I would class as critical. IMHO the new chain is low cost insurance.

neiljohnson

11,298 posts

238 months

Wednesday 2nd April 2014
quotequote all
djwilk said:
I am only going by r8black's recent result of around 550 fwhp, hence my goal that was supposedly somewhat realistic, no?
It was done at Amd everything makes big power there