HELP!!! blown head gasket
Discussion
hi Guys,
the wife was out in the car last night and the fan failed, over heated the engine, blew the return pipe off the radiator and subsequently blew the head gasket!
now I know this is a big job, but was wondering just how bad it is to do a head gasket on an LS2? and while its pulled apart what tuning can I do to it as I dont want to spend all that money fixing it to just have a standard car! all the car has at the moment is a cat back Walkinshaw exhaust, was thinking cam's? has anyone else had there head gasket go?
any help/advise would be greatly appreciated
cheer!
the wife was out in the car last night and the fan failed, over heated the engine, blew the return pipe off the radiator and subsequently blew the head gasket!
now I know this is a big job, but was wondering just how bad it is to do a head gasket on an LS2? and while its pulled apart what tuning can I do to it as I dont want to spend all that money fixing it to just have a standard car! all the car has at the moment is a cat back Walkinshaw exhaust, was thinking cam's? has anyone else had there head gasket go?
any help/advise would be greatly appreciated
cheer!
Yeah did the engine seize or hydrolock etc?
If not check the heads didnt warp. Probably good to skim anyway check block deck as well etc.
Clean it all up and reassemble. But add a cam, valve springs and perhaps a new set of lifters too.
That should sort things out nicely. Or add new heads for more depending on goals etc.
If not check the heads didnt warp. Probably good to skim anyway check block deck as well etc.
Clean it all up and reassemble. But add a cam, valve springs and perhaps a new set of lifters too.
That should sort things out nicely. Or add new heads for more depending on goals etc.
cheers so far guys! the wife shut down the engine near as soon as the return pope blew off, so hope there is no more damage. was looking on flee bay at cams, there are Lunati Voodoo cams for what seems a good price? anyone used them and if so what profile as there seems to be loads to choose from? also I take it valve springs are a must? but is it necessary to do lifters etc?
really appreciate the input/ideas!
really appreciate the input/ideas!
so the heads will need to be taken away and skimmed, has anyone done any head work to there LS2's, like a port and polish etc, is it worth it and what kind of cost would I be looking at? also with the heads off now is a good time to put a cam in, but no idea what profile? I'm looking at the Lunati cams but there is so many different ones! would love a wee pointer in the right direction. the cam would need to be ok for emissions, give a good lumpy idle and be a good increase across the rev range not just up top.
cheers guys.
cheers guys.
Go for max of zero overlap at 0.050 lumpy and emissions compliance dont go well together.
Something like a 222/226-114+4 has -4 overlap use lxl lobes and you will get around 0.600 lift.
Run some decent springs and you should be good to go.
A popular LS2 grind in Oz is the 224/228, but some like 228/232 though thats going to have +ve overlap so not as friendly on emissions.
LSR lobes will let you do a 223/227 comp do a few off the shelves around this level.
But you get the idea. low 22x intake and mid 22x exhaust with a nice lobe for decent lift and you should gain ~60rwhp
Something like a 222/226-114+4 has -4 overlap use lxl lobes and you will get around 0.600 lift.
Run some decent springs and you should be good to go.
A popular LS2 grind in Oz is the 224/228, but some like 228/232 though thats going to have +ve overlap so not as friendly on emissions.
LSR lobes will let you do a 223/227 comp do a few off the shelves around this level.
But you get the idea. low 22x intake and mid 22x exhaust with a nice lobe for decent lift and you should gain ~60rwhp
ringram said:
Go for max of zero overlap at 0.050 lumpy and emissions compliance dont go well together.
Something like a 222/226-114+4 has -4 overlap use lxl lobes and you will get around 0.600 lift.
Run some decent springs and you should be good to go.
A popular LS2 grind in Oz is the 224/228, but some like 228/232 though thats going to have +ve overlap so not as friendly on emissions.
LSR lobes will let you do a 223/227 comp do a few off the shelves around this level.
But you get the idea. low 22x intake and mid 22x exhaust with a nice lobe for decent lift and you should gain ~60rwhp
222/226 with ~.60x is what I have (albeit on ls1, with 115/+3 on EPS lobes), and I can somewhat dial the lumpy idle in or out with the tune. I think you're turning a £xxx job into a £x,xxx job mind, especially when you consider the tune and extra labour! Also, while you're in there, potentially new timing bits, oil pump, springs, push-rods, lifters, lifter trays, gaskets, head bolts (/studs)...Something like a 222/226-114+4 has -4 overlap use lxl lobes and you will get around 0.600 lift.
Run some decent springs and you should be good to go.
A popular LS2 grind in Oz is the 224/228, but some like 228/232 though thats going to have +ve overlap so not as friendly on emissions.
LSR lobes will let you do a 223/227 comp do a few off the shelves around this level.
But you get the idea. low 22x intake and mid 22x exhaust with a nice lobe for decent lift and you should gain ~60rwhp
I couldn't find anywhere particularly affordable for porting, if I were in your situation and dead-set on doing a cam now then consider efi live so you can sort the tune, and buy better heads later.
mailer555 said:
great advice guys. think I might leave the heads alone for now, but go for the cam as I might as well with the heads having to come off.
cheers.
Swapping the camshaft is still quite involved even with the heads off.cheers.
Strictly speaking, a cam swap doesnt need the heads to come off at all anyway. Most of the work is elsewhere.
yes it will be a little easier with heads off, but not a lot really.
As the heads are off, then of course having them worked on now would be the most sensible course of action well before a camshaft simply because they are off and it is the best time.
KMud said:
222/226 with ~.60x is what I have (albeit on ls1, with 115/+3 on EPS lobes), and I can somewhat dial the lumpy idle in or out with the tune. I think you're turning a £xxx job into a £x,xxx job mind, especially when you consider the tune and extra labour! Also, while you're in there, potentially new timing bits, oil pump, springs, push-rods, lifters, lifter trays, gaskets, head bolts (/studs)...
I couldn't find anywhere particularly affordable for porting, if I were in your situation and dead-set on doing a cam now then consider efi live so you can sort the tune, and buy better heads later.
Did you sort your idle with the cracker or follower tables?I couldn't find anywhere particularly affordable for porting, if I were in your situation and dead-set on doing a cam now then consider efi live so you can sort the tune, and buy better heads later.
ringram said:
Did you sort your idle with the cracker or follower tables?
A bit of everything, and some pet theories that may not sync up with some of weathermanshawn's tutorials. It's nearly there with respect to idle/idle transitions - might actually have some time to look at it again soon. Haven't moved on to spark yet, and will get COS3 on soon.Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff




h does something wrong.