Escort LS1 problems
Escort LS1 problems
Author
Discussion

sheepdip

Original Poster:

538 posts

206 months

Sunday 6th April 2014
quotequote all
Hi All

Escort is now up and running, and all legal.
I have a few problems - not suprising I guess!
The car has a miss-fire on small throttle openings. I have efilive software and it is logging low and high readings from the Maf. I have even watched and logged the over reading as it miss fires. Today I dis-connected the Maf and the miss-fire has gone with no difference in power or so it seems.
So this begs the questions - when running without the Maf does it run a safe map and if so how do I change this to give max power? I have seen info on the net but this seems to have disappeared due to US site worried about remaps and road going cars!

MyM8V8

9,468 posts

226 months

Sunday 6th April 2014
quotequote all
I think you need to recalibrate the maf, if you must use it? Are you using the same LS1 maf that came with the motor?

stevieturbo

18,105 posts

278 months

Monday 7th April 2014
quotequote all
sheepdip said:
Hi All

Escort is now up and running, and all legal.
I have a few problems - not suprising I guess!
The car has a miss-fire on small throttle openings. I have efilive software and it is logging low and high readings from the Maf. I have even watched and logged the over reading as it miss fires. Today I dis-connected the Maf and the miss-fire has gone with no difference in power or so it seems.
So this begs the questions - when running without the Maf does it run a safe map and if so how do I change this to give max power? I have seen info on the net but this seems to have disappeared due to US site worried about remaps and road going cars!
Where is the MAF located ? It doesnt take much to screw up airflow though one.

Solution, bin it and go MAFless. Will also make intake plumbing neater and easier.

sheepdip

Original Poster:

538 posts

206 months

Monday 7th April 2014
quotequote all
Mafless is the way I want to go but not sure which map the ecu uses. I have a wide band lamda and it reads OK with the map dis-connected but is it now running on a safe map? Power seems OK but maybe I have been spoilt over the years as was expecting more! I have another problem in that the bonnet wants to deform at speeds over 100mph! But I will be adding extra braces and vents to it tonight with a bit of luck.

MyM8V8

9,468 posts

226 months

Monday 7th April 2014
quotequote all
stevieturbo said:
Solution, bin it and go MAFless. Will also make intake plumbing neater and easier.
+1.

What do you mean which map will it use? Are you talking about low and high octane tables? Beauty of mafless is that ECU doesn't waste time referring to the maf and reads direct from the tables.

Have a look at AutoVE for LS1's on efilive. If the LS1 is from a 2004 CV8 there will be bags of power on the table for you to access.


ringram

14,702 posts

279 months

Monday 7th April 2014
quotequote all
As Gareth says there is only 1 map.
Mafless uses the same map as mafless, its just doesnt use the maf tables if its disabled.
BUT you do have to run a custom OS otherwise it will fail into low octane table.
A quick fix, which HSV did is to copy high octane table to low.
Knock retard will still work, but there will be no adaptive spark.

Read the autove tutorial and follow that to sort things out.
But perhaps first read up on the custom OS and go with cos3 or cos5 then do the autove etc..


stevieturbo

18,105 posts

278 months

Monday 7th April 2014
quotequote all
sheepdip said:
Mafless is the way I want to go but not sure which map the ecu uses. I have a wide band lamda and it reads OK with the map dis-connected but is it now running on a safe map? Power seems OK but maybe I have been spoilt over the years as was expecting more! I have another problem in that the bonnet wants to deform at speeds over 100mph! But I will be adding extra braces and vents to it tonight with a bit of luck.
LOL, you should see the shape my bonnet gets into !!

It's just a single skin of Kevlar, although I bonded some aluminium angle section in to brace it a little.

Over 100-120 or so at night I can see the front headlight through the gap.

Over 150-160 or so and it usually bends the two bonnet pins. Amazingly it has never come off though.

Mine must lift around 3" in between the hinges at speeds and about 2" at the front between the pins.

stigmundfreud

22,454 posts

241 months

Monday 7th April 2014
quotequote all
Disabling MAF is very easy, I also posted up what was part of a good base tune the other day which has a good spark table and runs semi-open loop

Its a couple of triggers to disable maf and its covered in the tuning guide from efi.

I like the MAF it keeps a watch over things but Richard likes the 2hp you theoretically get if you run without wink

stigmundfreud

22,454 posts

241 months

Monday 7th April 2014
quotequote all
http://www.pistonheads.com/gassing/topic.asp?h=0&a...

that's a link to (from memory) a fairly dialied in VE and spark map based on an LS1 with the stock MAF but also had long tubes but it will be a lot closer than a base tune.

You might not bother with DFCO but if you do the settings in the above thread also work nicely and if you are running a TC mode take a look for Swingtan's posts on efilive forum as I used his, in the wet, you couldn't even tell it was kicking in but it was very effective (doubt you will be running it though?)

stigmundfreud

22,454 posts

241 months

Monday 7th April 2014
quotequote all
taken from here http://forum.efilive.com/showthread.php?10846-Trac...

I ran these timings and they worked really nice, copied here in case the thread is ever pulled

swingtan said:
Originally Posted by swingtan View Post

The basic settings are.....
•All torque reduction control setting are set to off, except for B0517
•B0517: TCS Torque Reduction By Thrttle Option - is set to Yes.
•B2501: TCS Maximum Engine Torque - is set to a value over the expected peak torque. In mine it's 700 Nm
•B2502: TCS Minimum Engine Torque - is set to the least amount of torque wanted. Mine is set to 80 Nm
•B2503: Delivered Torque Upper Duty Cycle - set hi, 90% for me.
•B2504: Delivered Torque Lower Duty Cycle - set medium, 35% for me. I think this helps set the control of the torque delivery when TCS is active.
•B2514: TCS Throttle Limiter By Gear - All maxed out.
•B2517: TCS Throttle Limiter By Input Speed -This is where it all happens. Set torque limits for each gear and RPM to suit the traction expected. The real work is done in 1st and 2nd gear. Here are my settings....

1st Gear
•147.625000
•157.500000
•168.500000
•183.250000
•220.000000
•273.500000
•325.625000
•399.375000
•700.000000


2nd Gear
•162.750000
•173.875000
•189.875000
•215.250000
•258.125000
•314.875000
•388.375000
•480.500000
•700.000000
3rd and 4th are just higher settings again.
•B2522:Torque Reduction Max - I have this set to 100 Nm


Now, with these settings and TCS turned on ( I.E. I haven't turned it off ) taking off hard on good dry bitumen has virtually no "detectable" wheel spin when sitting in the drivers seat. You can also feel the torque management release as you go through 3000 RPM. If you check the log data though, you can see around 5 to 10 kmh of wheel spin. So there is plenty of power getting to the rear wheels, just not enough to really light up the tires.

Simon.
the thread has further readings, I tested these on an e38 ls3 but the tables should be in the LS1 ecu too (I think)

ringram

14,702 posts

279 months

Monday 7th April 2014
quotequote all
Stig, FAIL! These are not in the LS1.

You have gone from the light for too long. Faecal matter now flows more voluminously.

Can I recommend you speak to Dougie and order an HSV GTS so that you can regain some of the knowledge which you have lost.

stigmundfreud

22,454 posts

241 months

Monday 7th April 2014
quotequote all
ah well for any of the e38 guys the tables work nicely!

I couldn't afford a GTS and why would I want to go from one of the nicest looking cars to dame Edna's discharge?

stevieturbo

18,105 posts

278 months

Monday 7th April 2014
quotequote all
stigmundfreud said:
I like the MAF it keeps a watch over things but Richard likes the 2hp you theoretically get if you run without wink
Only watches over while it works, and is used and scaled correctly for the application, same as any other sensor

But it does complicate installation, it can go faulty, and it can restrict.

There are very few applications where I see a MAF as a beneficial thing.

Maybe if travelling thousands of miles across continents, mountain ranges to sea level, extreme temperature swings....then yes it would help.

For UK stuff...nope.

stigmundfreud

22,454 posts

241 months

Monday 7th April 2014
quotequote all
its even worse as I now have two maf's to worry about and yes they do cause problems but when scaled right and working they are good. If the car has good set up and other sensors then altitude etc shouldn't be a problem, horses for courses I guess. I will probably ditch mine in the near future as at 500 a pop they aint cheap (or reliable) so its cheaper to get an SD tune