What garage floor??
Discussion
I am just about to pour the floor on my new garage. It will be used for hobby work on cars and bikes etc but no major traffic. Looking for suggestions on which floor prep to use. Approx 600sq feet.
I will be power floating the floor tomorrow night but the decision from there is wide open.
Floor paint, 2 pack epoxy coating, floor tiles or high shine polished finish.
Any ideas?
I will be power floating the floor tomorrow night but the decision from there is wide open.
Floor paint, 2 pack epoxy coating, floor tiles or high shine polished finish.
Any ideas?
When we built our garage (about 10 years ago) we decided on putting down Racedeck floor tiles. I was easily able to lay them myself and they have proved very durable and look good.
You'll see some pics of it in some of the photos of most of the cars on my website:
e.g http://www.bmwclassics.co.uk/gallery/index.php?spg...
At the time it was only available direct from the manufacturer in Salt Lake City, Utah so I had to buy it from them and have it air-freighted over. There was then Import Duty and Vat to pay on it so it ended being quite an expensive exercise.
However, it now seems they have a U.K agent:
http://www.racedeckflooring.co.uk/Racedeck_Floorin...
I think there are now also similar alternatives available in the U.K.
You'll see some pics of it in some of the photos of most of the cars on my website:
e.g http://www.bmwclassics.co.uk/gallery/index.php?spg...
At the time it was only available direct from the manufacturer in Salt Lake City, Utah so I had to buy it from them and have it air-freighted over. There was then Import Duty and Vat to pay on it so it ended being quite an expensive exercise.
However, it now seems they have a U.K agent:
http://www.racedeckflooring.co.uk/Racedeck_Floorin...
I think there are now also similar alternatives available in the U.K.
kambites said:
How well do the plastic floor tiles deal with things like trolley jacks and axle stands? Also how easy is it to get things like oil and hydraulic fluid off them?
As I found out, they don't deal with jacks and stands being stood directly on to them. That causes dimbles in them. It's best to put something between the jack/stands and the floor. I have some squares of wood for this purpose.Oil etc doesn't affect them and can be easily cleaned off. I did however make one mistake. I once washed off the whole engine underside of a filthy old car inside the garage. The water and gunk seeped between and under the tiles. So at one place I do get a continual staining appearing between the tiles. This is annoying because its position is such that I would have to take-up a major postion of the floor it get to it to clean underneath. There seems to be no way to easily remove individual tiles from the others if the ones you want to remove are in the middle of others.
Viper said:
a few of my mates have laid ceramic tiles recently, and they look good, are durable even with trolley jacks and are easy to clean
I did consider this at the time but the large area I was going to have to cover meant it was going to be prohibitively expensive for me. It wasn't so much just the purchase of the tiles and other materials but more so the labour cost of having them laid as this wasn't something I could do myself. The quotes I had for laying them ruled it out for me.Hmm, not being able to use a trolley jack and stands without arsing about with bits of wood would be a pain.
I think I'd go for polished concrete. It's resistant to just about everything, extremely easy to keep clean, lasts forever and I think relatively cheap. They do get a bit cold in the winter if you're crawling around under cars, though.
I think I'd go for polished concrete. It's resistant to just about everything, extremely easy to keep clean, lasts forever and I think relatively cheap. They do get a bit cold in the winter if you're crawling around under cars, though.
Gassing Station | General Gassing | Top of Page | What's New | My Stuff



