Halfords Trolley Jack- loses height over time
Halfords Trolley Jack- loses height over time
Author
Discussion

LittleEnus

Original Poster:

3,506 posts

205 months

Thursday 26th March 2015
quotequote all
Bought it in the sales but only just used it for the first time. It gets the rear of the car up nicely and I put some axle stands underneath. Next morning the trolley jack's lifter was right at the bottom.

Do I need more hydraulic fluid or do I need to bleed out the air? It drops even without weight on it over time.

Any help appreciated. Cheers

I'm replacing lower control arms on the rear in case you wanted to know smile

illmonkey

19,842 posts

229 months

Thursday 26th March 2015
quotequote all
Are you tightening the release valve enough, or is it moving?

mygoldfishbowl

4,304 posts

174 months

Thursday 26th March 2015
quotequote all
It's fked take it back.

kambites

71,703 posts

252 months

Thursday 26th March 2015
quotequote all
Very few trolley jacks will stay up with significant load on them but it really should do without load. I'd take it back because the seals always get worse with time and it's probably going to become unusable far quicker than it should do.

TooMany2cvs

29,008 posts

157 months

Thursday 26th March 2015
quotequote all
You shouldn't NEED to leave it extended for any period, since you shouldn't be using the jack to support, only to lift. But it's very likely the drop screw isn't sealing properly. If it were the seals in the ram, you'd be losing fluid onto the floor.

Take it back, get your money back, go to http://www.sgs-engineering.com/hydraulic-jacks/tro...

LittleEnus

Original Poster:

3,506 posts

205 months

Thursday 26th March 2015
quotequote all
illmonkey said:
Are you tightening the release valve enough, or is it moving?
Seem to be.

Not sure I have the receipt for this. It is their own brand but not sure I could pull off a refund?

mwstewart

8,613 posts

219 months

Thursday 26th March 2015
quotequote all
You shouldn't rely on a jack to do this. A lot of them will go down overnight.

BenWRXSEi

2,535 posts

165 months

Thursday 26th March 2015
quotequote all
mwstewart said:
You shouldn't rely on a jack to do this. A lot of them will go down overnight.
He's already said he uses axle stands, the jack is descending without any load on it wink

OP, if the release valve is tight and it's still going down, take it back. I gather they're usually pretty good about exchanges.

LittleEnus

Original Poster:

3,506 posts

205 months

Thursday 26th March 2015
quotequote all
Cheers guys smile

Enough of the safety first lectures hehe I am using axle stands.


PoleDriver

29,624 posts

225 months

Thursday 26th March 2015
quotequote all
The first rule about buying stuff from Halfrauds is... Don't buy stuff from Halfrauds!

grahamr88

426 posts

204 months

Thursday 26th March 2015
quotequote all
PoleDriver said:
The first rule about buying stuff from Halfrauds is... Don't buy stuff from Halfrauds!
Unless you want generally decent tools, at very good prices, with (in some cases) a lifetime guarantee, from somewhere that's open evenings and weekends...

kambites

71,703 posts

252 months

Thursday 26th March 2015
quotequote all
PoleDriver said:
The first rule about buying stuff from Halfrauds is... Don't buy stuff from Halfrauds!
Not really. They sell some of the best value DIYers' tools on the market. My socket set has had the best part of fifteen years of fairly heavy DY use and is still immaculate; it only cost about £40.

PoleDriver

29,624 posts

225 months

Thursday 26th March 2015
quotequote all
And do they give a lifetime guarantee for the cheaply made trolley jacks they sell?

motco

17,669 posts

277 months

Thursday 26th March 2015
quotequote all
TooMany2cvs said:
You shouldn't NEED to leave it extended for any period, since you shouldn't be using the jack to support, only to lift. But it's very likely the drop screw isn't sealing properly. If it were the seals in the ram, you'd be losing fluid onto the floor.

Take it back, get your money back, go to http://www.sgs-engineering.com/hydraulic-jacks/tro...
I bought one from SGS and it went down on load by 25mm in about 5 minutes. They were good about replacing it though and the new one is pretty good - not perfect, but good. Most will sink slowly, as already said. The problem is that most cars have one jacking point per 'corner' and there's nowhere officially approved to put an axle stand except where the jack already is.

kambites

71,703 posts

252 months

Thursday 26th March 2015
quotequote all
PoleDriver said:
And do they give a lifetime guarantee for the cheaply made trolley jacks they sell?
No their cheap trolley jacks are appalling, although probably no worse than anything else for the money. hehe

Pothole

34,367 posts

313 months

Thursday 26th March 2015
quotequote all
mwstewart said:
You shouldn't rely on a jack to do this. A lot of them will go down overnight.
Only a few Jills will....

snowley

183 posts

157 months

Thursday 26th March 2015
quotequote all
Pothole said:
nly a few Jills will....
Beat me to it....