DIY Mechanic disasters
Discussion
We were having a chat in the office this morning about DIY Mechanic disasters.
Luckily I haven't had too many, the worst being gearbox oil (worst smelling thing known to mankind) running down my arm thinking the gearbox needed topping up when it didn't.
What are your funniest/ worst stories?
Luckily I haven't had too many, the worst being gearbox oil (worst smelling thing known to mankind) running down my arm thinking the gearbox needed topping up when it didn't.
What are your funniest/ worst stories?
Krikkit said:
whoops, thank you 
I'm by no means an experienced spanner monkey, but I managed to install a supercharger kit in my Civic which was pretty daunting but good fun at the same time, if you call good fun swearing at some of the bolts on the intake manifold (at one stage I'm pretty sure I was fiddling about with about four socket extensions!). This went completely smoothly and I surprised myself as the garage quoted 5 hours labour, so a fairly big job - chuffed as nuts... then the other week my wife got a slow puncture on the rear off side of her Audi, I jacked the car up with the pathetic jack from the boot, got the wheel off and realised as the car was creaking that I forgot to put it in gear. It was on a slight slope and had rolled forwards due to the s
te electric handbrake, falling off the jack and onto the disc! Cue much faffing about with two other crap jacks and some axle stands, trying desperately in vain to get it back level. Proper Barry Chuckle stuff, must have given the neighbours a laugh at least
te electric handbrake, falling off the jack and onto the disc! Cue much faffing about with two other crap jacks and some axle stands, trying desperately in vain to get it back level. Proper Barry Chuckle stuff, must have given the neighbours a laugh at leastSirSquidalot said:
Spent a good 2 hours one night trying to change a coolant temp sensor on a Seat Ibiza. Would it come out? Would it f
k?
Next day in the day light, oh i need to remove that clip. 30 second job
I had similar when removing the chargecooler from my Celica, pushed the silicone hose up off the turbo and tugged the chargecooler but it wouldn't move, swore lots and got very red in the face and it was stuck. Pushed the hose downwards onto the turbo and the chargecooler pretty much jumped off on it's own
k?Next day in the day light, oh i need to remove that clip. 30 second job


Wasn't there the guy who came on here not too long ago while changing a clutch on his Clio, asking for us to identify a part which didn't seem to fit anywhere. Small circular object a bit like a bearing, and caused him some concern as to where it came from...
Turned out to be the wheel from his trolley jack.
Turned out to be the wheel from his trolley jack.
Me and my Dad often work on our Vx220 together, we've had 2 very memorable moments when working on that car:
The first being in an attempt to swap the brake discs the driver's side retaining bolt rounded off, this probably wouldn't be so bad if the material the bolt was made out of wasn't the strongest thing known to man and an even tougher metal than the disc its attempting to keep in place. This lead to 3 days of drilling, lots of swearing and eventually a swapped over disk but we still have the remnants of that bolt in place, attempting to remove the rest of it isn't worth the hassle compared to having to line up the holes on the disk whenever we put the wheel back on.
The 2nd time being a lot more dangerous if we hadn't noticed it - while replacing the wishbone bushes all went well or so we thought, when we came back the next day to admire our handy work and found we hadn't actually bolted the wishbone in place as the bolt had missed the hole in the bush (giggedy)
That could've been very very messy if we attempted to run with the car like that
The first being in an attempt to swap the brake discs the driver's side retaining bolt rounded off, this probably wouldn't be so bad if the material the bolt was made out of wasn't the strongest thing known to man and an even tougher metal than the disc its attempting to keep in place. This lead to 3 days of drilling, lots of swearing and eventually a swapped over disk but we still have the remnants of that bolt in place, attempting to remove the rest of it isn't worth the hassle compared to having to line up the holes on the disk whenever we put the wheel back on.
The 2nd time being a lot more dangerous if we hadn't noticed it - while replacing the wishbone bushes all went well or so we thought, when we came back the next day to admire our handy work and found we hadn't actually bolted the wishbone in place as the bolt had missed the hole in the bush (giggedy)
That could've been very very messy if we attempted to run with the car like that

Gassing Station | General Gassing | Top of Page | What's New | My Stuff



