Question for Tyre fitters
Discussion
Question for Tyre fitters here,
Recently stuck two new Continental Sport contacts on my car and used a crumby large chain of stores as they were on offer there and consequently much cheaper.
The receipt came back saying both wheels required a large amount of weight fitted to balance and consequently were deemed buckled. Since having the tyres fitted there is a wheel wobble, annoyingly at around the 70mph mark. Now, the car never did this prior to fitting the new tyres.
My question is have the tyres been fitted correctly? I know in days gone by some tyres had a dot printed on the wall to indicate the heaviest point on the tyre and this was normally fitted near the valve and then balanced. Do Continentals have something similar or am I barking up the wrong tree here? Naturally I'd rather take them elsewhere and have them refitted and balanced than replace the wheels altogether
Recently stuck two new Continental Sport contacts on my car and used a crumby large chain of stores as they were on offer there and consequently much cheaper.
The receipt came back saying both wheels required a large amount of weight fitted to balance and consequently were deemed buckled. Since having the tyres fitted there is a wheel wobble, annoyingly at around the 70mph mark. Now, the car never did this prior to fitting the new tyres.
My question is have the tyres been fitted correctly? I know in days gone by some tyres had a dot printed on the wall to indicate the heaviest point on the tyre and this was normally fitted near the valve and then balanced. Do Continentals have something similar or am I barking up the wrong tree here? Naturally I'd rather take them elsewhere and have them refitted and balanced than replace the wheels altogether
If I fit tyres and the machine calls for a lot of weight I usually break the beads again and spin them 180 degrees and see if that helps.
Tyres are easy to balance yet so many seem to get it wrong.
Another thing that can happen is if there is a load of soap used to help get them over the rim and then you take the car straight after fitting and accelerate briskly the tyre can spin on the rim and that really buggers up the balance!
Tyres are easy to balance yet so many seem to get it wrong.
Another thing that can happen is if there is a load of soap used to help get them over the rim and then you take the car straight after fitting and accelerate briskly the tyre can spin on the rim and that really buggers up the balance!
JimmyConwayNW said:
I thought this was going to be about when tyre fitters refer to themselves as mechanics.
Which forces mechanics to pretend to be engineers, so that engineers have to spend 300 quid getting chartered for no real benefit what-so-ever.The trick is to look at the shoes: Safety shoes and a cheap suit = engineer, safety shoes and overalls = mechanic, safety shoes on wrong feet = tyre fitter.
That said one of the local fitters isn't terrible, and actually do the job properly. Torques and pressures and everything. Top guys.
I think the dot was only to show which way round the tyre should befitted on the rim for directional tyres. i.e. if you could / couldn't see the dot, depending upon convention, on all 4 tyres then one was the wrong way around, a manufacturing aid in the OEM plant. I couldn't imagine a process that would identify the 'heaviest' point of a tyre that isn't fitted to a rim (how would the tyre OEM determine where to put the dot?). The tyre and wheel need to be balanced in combination.
If you didn't get a wobble before but do after the tyre has been changed it suggests there's something wrong with the new fitment. I'd go back and ask for it to be done again before scrapping the wheels.
If you didn't get a wobble before but do after the tyre has been changed it suggests there's something wrong with the new fitment. I'd go back and ask for it to be done again before scrapping the wheels.
Doobs too said:
I couldn't imagine a process that would identify the 'heaviest' point of a tyre that isn't fitted to a rim (how would the tyre OEM determine where to put the dot?).
Make a round jig that holds a tyre and fit it on a bearing. Balance your jig. Push new tyre on. Watch as the whole thing rotates until the heaviest bit of the tyre is at the bottom. Dab with paint.I imagined that, but then I'm a little drunk and have very little idea of what processes actual tyre OEMs could do.
morgrp said:
Cheers for the advice guys,
I'll run it up the local tyre place tomorrow and get them re-done - hopefully will cure the problem
The local tyre place that charge more because they employ staff with brains unlike the cheap place you went to? You know what will happen if everybody acts like you don't you?I'll run it up the local tyre place tomorrow and get them re-done - hopefully will cure the problem
Spangles said:
The local tyre place that charge more because they employ staff with brains unlike the cheap place you went to? You know what will happen if everybody acts like you don't you?
Yeh, the local guy will thrive. 'Cos instead of making 3ppll (pence per ling long) of profit, he's now fully booked with double priced fittings sorted out kwik fits mess. 
Zoobeef said:
Leptons said:
Nope, there is a dot at the tyres heaviest point. Supposed to be fitted 180 degrees from the valve to counter each other out.
I wonder why it wouldn't be easier to dot the lightest bit then line it up with the valve.If, as is often the case, the tyre has been mounted any old how, there will usually be a weight 180 degrees opposite.
Paddymcc said:
The last tyre I had fitted the chap took great care fitting the tyre and then went to stick it back on the car.
He seemed perplexed and greatly inconvenienced when I asked him was he going to bother balancing it before putting it back on the car.
A while ago I had 4 new Sava tyres fitted to some Minilites, the fitter was doing me an FOC favour, at the end of the day.He seemed perplexed and greatly inconvenienced when I asked him was he going to bother balancing it before putting it back on the car.
He said "didn't need balancing" I'd not heard of that before so was a little sceptical. The car ran perfectly.
I've had some success with "Road Force" balancing with some wheels and tyres that just wouldn't balance up properly.
Edited by PositronicRay on Thursday 16th April 07:42
Had some tyres fitted to my XR3 many moons ago by Kwikfit , drove about half a mile when I realised they hadn't been balanced correctly.
Got back to be told the balance machine wasn't working !
The manager couldn't understand my displeasure or amazement that they'd fitted them in the first place.
In those days Tom Farmer advertised that you could speak to him directly if you had a problem , that was another Kwikfit fallacy.
Got them sorted eventually but what a carry on.
Got back to be told the balance machine wasn't working !
The manager couldn't understand my displeasure or amazement that they'd fitted them in the first place.
In those days Tom Farmer advertised that you could speak to him directly if you had a problem , that was another Kwikfit fallacy.
Got them sorted eventually but what a carry on.
Gassing Station | General Gassing | Top of Page | What's New | My Stuff


