Knock in low gears when lift off throttle
Discussion
Car in question is an RS Clio (2008)
Seem to have a strange issue whenever I change between 1st/2nd and 2nd/3rd gear at low RPM.
I can't quite work out if the knock is because I lift off the throttle, or press the clutch, or a combination of the two.
If I wait until 3K RPM or higher, or keep the accelerator very very slightly pressed the knock doesn't seem to occur.
The gearbox seems ok, as does the clutch - no slipping, no crunches on gear shifts etc.
After much Googling, I'm wondering if it could be the engine mounts? Lifting off the throttle adds some engine vibration which is causing the knock? The car does sort of "jump" when it happens and there's a sort of "bang/knock". It doesn't seem to make too much difference if the car is warmed up or run from cold, and it doesn't happen every time, it's more "intermittent".
Any ideas? Anything I can check/look for?
Seem to have a strange issue whenever I change between 1st/2nd and 2nd/3rd gear at low RPM.
I can't quite work out if the knock is because I lift off the throttle, or press the clutch, or a combination of the two.
If I wait until 3K RPM or higher, or keep the accelerator very very slightly pressed the knock doesn't seem to occur.
The gearbox seems ok, as does the clutch - no slipping, no crunches on gear shifts etc.
After much Googling, I'm wondering if it could be the engine mounts? Lifting off the throttle adds some engine vibration which is causing the knock? The car does sort of "jump" when it happens and there's a sort of "bang/knock". It doesn't seem to make too much difference if the car is warmed up or run from cold, and it doesn't happen every time, it's more "intermittent".
Any ideas? Anything I can check/look for?
RobinBanks said:
Is it nothing to do with rev matching? Ie you lift off the accelerator and the revs drop and it's mismatched.
Or have I misunderstood?
Think slight misunderstanding, it's on up-shifts so no rev-matching. Or have I misunderstood?
So for example car in 1st, start rolling, accelerate up to 2.5K RPM, lift off accelerator/press clutch [KNOCK OCCURS], clutch out to engage 2nd, accelerate again.
The movement's are pretty much all-in-one fluid motion in the space of about 1 second.
996TT02 said:
Engine mounts most likely culprit on a FWD car.
You may even be able to rock the engine by push-pulling on it.
Otherwise failed suspension bushes allowing one or both of the struts to move.
I tried giving the engine a good shove, it moved a little, but nothing that I'd call "excessive". You may even be able to rock the engine by push-pulling on it.
Otherwise failed suspension bushes allowing one or both of the struts to move.
I had a similar thing in a Montego (was a while ago in my defence !), was ok under load, come off the gas and clunk, bag on the gas, clunk.
Got progressively worse until I hoofed it out of a junction and the contents of the diff exited through the bottom of the car at high speed, I coasted to outside our house leaving a trail of cogs, chunks of casing and gearbox oil.
It was the centre pin in the diff that had worn, so the clunk was the slack being taken up and released, the pin was over half the diameter it should be and booting it stressed it enough that the whole thing failed in a most spectacular manner.
So, if there is no play in anything else, it may be something like that
Got progressively worse until I hoofed it out of a junction and the contents of the diff exited through the bottom of the car at high speed, I coasted to outside our house leaving a trail of cogs, chunks of casing and gearbox oil.
It was the centre pin in the diff that had worn, so the clunk was the slack being taken up and released, the pin was over half the diameter it should be and booting it stressed it enough that the whole thing failed in a most spectacular manner.
So, if there is no play in anything else, it may be something like that
CallorFold said:
If it is the engine mounts, is there some sort of explanation why it only happens in lower gears and at low RPM? I'd expect there to be more engine vibration at higher revs/higher gears? Rather than the other way round.
It isn't engine vibration that is the problem, it is the leverage the torque is putting through the mounts which is greater during acceleration in the lower gears, at lower speed as the engine is working harder to shift the mass of the car and it has more leverage due to being in a lower gear.CallorFold said:
996TT02 said:
Engine mounts most likely culprit on a FWD car.
You may even be able to rock the engine by push-pulling on it.
Otherwise failed suspension bushes allowing one or both of the struts to move.
I tried giving the engine a good shove, it moved a little, but nothing that I'd call "excessive". You may even be able to rock the engine by push-pulling on it.
Otherwise failed suspension bushes allowing one or both of the struts to move.
If you can rock it a little, it can generate enough torque to rock itself more.
There's a thread running on the Clio forum currently where someone seem's to have a similar/identical issue -
They been recommended getting the upper stabiliser and the lower torque link replaced. (Upper stabiliser is the part in the pictures above), and I believe the lower torque link is the "dog bone mount"?
So I think I'll have a look at replacing those first.
They been recommended getting the upper stabiliser and the lower torque link replaced. (Upper stabiliser is the part in the pictures above), and I believe the lower torque link is the "dog bone mount"?
So I think I'll have a look at replacing those first.
Edited by CallorFold on Wednesday 15th April 12:58
Gassing Station | General Gassing | Top of Page | What's New | My Stuff


