E36 M3 clocks into a nonM...
E36 M3 clocks into a nonM...
Author
Discussion

dannyDC2

Original Poster:

7,543 posts

199 months

Monday 15th February 2016
quotequote all
Afternoon all,

In my previous E36 the previous owner had retrofitted M3 clocks and used the M3 oil temp sensor that usually runs into the S50 oil filter housing, as a sump plug.

I loved having oil temp sensor (a bit geeky I know), and now that I've got another E36 I want to do the same, but I'm wondering if I can use an aftermarket sensor somewhere in the M52 oil filter housing?

This would reduce cost, but also reduce the risk of breaking the sensor when changing oil, something I did do once before.

http://www.ebay.co.uk/itm/Aftermarket-Gauge-Univer...

It would be this kind of sensor I would look to use. They just have the two wires, a ground and a signal. I know the M3 clocks only have a signal wire too, so where does the power come from, or does it not need any power?

Thanks for any help with figuring this out. If people have a better idea hit me!

Cheers
Dan

Dannbodge

2,393 posts

152 months

Monday 15th February 2016
quotequote all
From what I can recall, the sensor is just a thermal resistor so the clocks provide the power and the amount of resistance that it sees determines the temperature of the oil. The M3 sensor has a ground and signal wire:
http://wedophones.com/Manuals/BMW/1998%20BMW%20318...

The biggest issue I can recall was finding somewhere that had a constant flow of oil, rather than just sitting in a pool which would take forever to heat up.

Alternatively you could get a tiny sensor and have the banjo bolt for one of the oil lines drilled and tapped to accept it:
http://sourceautomotive.biz/images/products/detail...

Edited by Dannbodge on Monday 15th February 15:27


Edited by Dannbodge on Monday 15th February 15:28

dannyDC2

Original Poster:

7,543 posts

199 months

Monday 15th February 2016
quotequote all
Dannbodge said:
From what I can recall, the sensor is just a thermal resistor so the clocks provide the power and the amount of resistance that it sees determines the temperature of the oil. The M3 sensor has a ground and signal wire:
http://wedophones.com/Manuals/BMW/1998%20BMW%20318...

The biggest issue I can recall was finding somewhere that had a constant flow of oil, rather than just sitting in a pool which would take forever to heat up.

Alternatively you could get a tiny sensor and have the banjo bolt for one of the oil lines drilled and tapped to accept it:
http://sourceautomotive.biz/images/products/detail...

Edited by Dannbodge on Monday 15th February 15:27


Edited by Dannbodge on Monday 15th February 15:28
Taking a reading from a pool of oil wouldn't really concern me, that's where I read it on my old E36 from the sump.

Thanks for the link, I'll check em!

E-bmw

13,666 posts

183 months

Monday 15th February 2016
quotequote all
If you can get one of those (banjo-bolt type with the drilled end as per the link) the same as the vanos banjo then that is your real easy answer.

Drilled 1/8" NPT as per the link to your sensor.

dannyDC2

Original Poster:

7,543 posts

199 months

Tuesday 16th February 2016
quotequote all
I think I'll likely be buying a spare bolt and drilling/tapping that. Those online ones are £28, plus £28 shipping! Yikes that's a lot for a bolt.

Thanks chaps.

E-bmw

13,666 posts

183 months

Tuesday 16th February 2016
quotequote all
Just be careful & check the thread of the sensor.

I know it sounds stupid, but 1/8" NPT looks very similar to m10 x 1.0 but is not, and don't forget it is tapered, so make sure you google the correct drill size & get the correct tap.

dannyDC2

Original Poster:

7,543 posts

199 months

Tuesday 16th February 2016
quotequote all
E-bmw said:
Just be careful & check the thread of the sensor.

I know it sounds stupid, but 1/8" NPT looks very similar to m10 x 1.0 but is not, and don't forget it is tapered, so make sure you google the correct drill size & get the correct tap.
Thanks sir. I already have a spare 1/8" NPT sensor so should be good to go with that. Will need to buy the tools, but I'd rather have them spare for next time smile

All the best.