problems after fitting new vanos seals
Discussion
Hi all
done a lot of searching but nothing specific to this please read and you'll see why..
I recently installed new vanos seals on my 1999 saloon with 64k on clock (from I6 automotive sheffield uk) and installed them myself. Im not a mechanic but was pretty straightforward and i THINK everything went as it should. I started the car and drove it for about 30 miles in total without any issues. Didnt notice much difference but its said that a couple hundred miles run in period for management system to adjust and seals to sit in is normal.
So started the car and immediately a loud metallic 'klanging' sound started coming from the vanos / inlet manifold area. Switched off engine immediately! had a good look around engine bay and found a tear the usual hole in my lower intake boot. I replaced the boot and then noticed that the exhaust solenoid had come loose and disconnected (I obviously hadnt put it on properly). I thought aha !! thats bound to be the cause of the metalic 'klanging' sound. I started car and to my relief all sounded fine.
Then my problems started ! I now have a lumpy idle .. It varies as sometimes its just a little lumpy but other times i start the car its enough to start making the car shake side to side. I have purposely taken the car 200 miles and now over 'spirited' driving as suggested by bessian systems guide. All this has done is shown me that the car seems 'resistant' throughout the entire rev range. On 3 occasions i have started the car and its really struggled to get passed 2000 revs.. switching the engine off and on again sorted that immediate issue out , but i still had rough idle etc.
Now i dont know if this is related or just weird timing but almost immediately after I replaced the lower boot , an EXISTING (since I bought car) vacuum leak / suction sound became worse. Whenever i took my foot OFF the accelerator pedal the sound like someone sucking up fluid through a straw can be heard (what is this???? cant find anyone describing this specific issue) but now its also when I put my foot down. The MPG economy gauge has also started fluctuating when I come to a stop and makes the vacuum leak sucking sound.
I haven't taken to a garage yet and haven't had a diagnostic done, which is next, but then i'm at thier mercy and i'd like to be as informed as possible to the causes of this...
I dont believe i fitted the seals incorrectly .. it was very straightforward really. Im worried that the disconnected solenoid sensor that caused the 'klanging' has damaged something , or have the worsened vacuum leaks caused this ?
done a lot of searching but nothing specific to this please read and you'll see why..
I recently installed new vanos seals on my 1999 saloon with 64k on clock (from I6 automotive sheffield uk) and installed them myself. Im not a mechanic but was pretty straightforward and i THINK everything went as it should. I started the car and drove it for about 30 miles in total without any issues. Didnt notice much difference but its said that a couple hundred miles run in period for management system to adjust and seals to sit in is normal.
So started the car and immediately a loud metallic 'klanging' sound started coming from the vanos / inlet manifold area. Switched off engine immediately! had a good look around engine bay and found a tear the usual hole in my lower intake boot. I replaced the boot and then noticed that the exhaust solenoid had come loose and disconnected (I obviously hadnt put it on properly). I thought aha !! thats bound to be the cause of the metalic 'klanging' sound. I started car and to my relief all sounded fine.
Then my problems started ! I now have a lumpy idle .. It varies as sometimes its just a little lumpy but other times i start the car its enough to start making the car shake side to side. I have purposely taken the car 200 miles and now over 'spirited' driving as suggested by bessian systems guide. All this has done is shown me that the car seems 'resistant' throughout the entire rev range. On 3 occasions i have started the car and its really struggled to get passed 2000 revs.. switching the engine off and on again sorted that immediate issue out , but i still had rough idle etc.
Now i dont know if this is related or just weird timing but almost immediately after I replaced the lower boot , an EXISTING (since I bought car) vacuum leak / suction sound became worse. Whenever i took my foot OFF the accelerator pedal the sound like someone sucking up fluid through a straw can be heard (what is this???? cant find anyone describing this specific issue) but now its also when I put my foot down. The MPG economy gauge has also started fluctuating when I come to a stop and makes the vacuum leak sucking sound.
I haven't taken to a garage yet and haven't had a diagnostic done, which is next, but then i'm at thier mercy and i'd like to be as informed as possible to the causes of this...
I dont believe i fitted the seals incorrectly .. it was very straightforward really. Im worried that the disconnected solenoid sensor that caused the 'klanging' has damaged something , or have the worsened vacuum leaks caused this ?
I assume you mean the large o-ring etc in the Vanos piston.
How did you fit the seals?
There are 2 ways to do it, the normal way requires the operating gear for the cam to be re-aligned afterwards.
There is another way that I worked out meaning that it is done in-place & requires no re-alignment, no cam locking & takes 30 min instead of 3 hours.
How did you fit the seals?
There are 2 ways to do it, the normal way requires the operating gear for the cam to be re-aligned afterwards.
There is another way that I worked out meaning that it is done in-place & requires no re-alignment, no cam locking & takes 30 min instead of 3 hours.
When I replaced the vanos seals on my M50 (single vanos on the intake) I had a couple of air leaks that gave very similar symptoms. The idle was very rough and sometimes would stall and it was very hit and miss with the performance. Turns out that there was a split intake hose that was causing air to enter after the MAF which resulted in the wrong AFR. Replacing the split hose cured the idle, however I did have to re-align the vanos as it was a degree or two out so felt very flat.
All sorted afterwards though, hope it helps.
All sorted afterwards though, hope it helps.
Gassing Station | BMW General | Top of Page | What's New | My Stuff


