Why wont my cooling system bleed after new parts?
Why wont my cooling system bleed after new parts?
Author
Discussion

wirewick

Original Poster:

8 posts

140 months

Monday 13th June 2016
quotequote all
I am not the best with terminology, so please bear with me.

I just changed out all of my cooling system parts on my E36 328 w/ M52 Engine (waterpump, hoses, radiator, thermostat, expansion bottle)

I have experience bleeding this system but I am having some trouble this time around. The issue is that I do not see coolant streaming out from the little hole inside/on top of the expansion bottle. The system seems to have taken up the appropriate amount of fluid, and I was able to let out the air through the bleeder screw. But for whatever reason, this time around the coolant is not streaming out into the bottle from the little hole. This has me confused because this hole along with the bleeder screw are connected to the radiator via the same hose.

Does anyone have a clue what is going on here?

Ciff

50 posts

165 months

Monday 13th June 2016
quotequote all
Run it at 2.5k rpm and you will see coolant moving into expansion tank

When I bleed mine I raise front of car fill with bleed screw out give it 30 minutes to settle. Refit bleed screw and radiator cap then run it with heater on full at 2.5k for a minute and its all done. Top up if needed

E-bmw

13,657 posts

183 months

Monday 13th June 2016
quotequote all
^^^^ wot 'e said.

That is basically the preferred method of bleeding the system on the m50/m52 engines.

iSore

4,011 posts

175 months

Monday 13th June 2016
quotequote all
M52's can be a cow to bleed, worse on cars with air con. What you can try is disconnecting the long hose that goes from the base of the header tank from where it meets the heater stub on the bulkhead - disconnect it here and pour coolant down the hose until it''s full and starts to dribble from true heater valve/stub. Another trick is to unscrew the electric fan switch or brass blanking plug. Finally, what I've always done is disconnecting the top hose and refill the cooling staten through there, a litre at a time.

Collectingbrass

3,020 posts

226 months

Monday 13th June 2016
quotequote all
Ciff said:
Run it at 2.5k rpm and you will see coolant moving into expansion tank

When I bleed mine I raise front of car fill with bleed screw out give it 30 minutes to settle. Refit bleed screw and radiator cap then run it with heater on full at 2.5k for a minute and its all done. Top up if needed
Thank you, I did the same on mine this weekend and couldn't get the fker to bleed either so this is a big help.

helix402

7,913 posts

213 months

Monday 13th June 2016
quotequote all
Ignition on, fan on. Heater set to hot. Pour in ready mixed 50/50 af/water or ready mix, bleed, using all bleed screws. Sorted.

wirewick

Original Poster:

8 posts

140 months

Tuesday 14th June 2016
quotequote all
Thanks for all the tips. Unfortunately nothing seems to be working.

I think there is a blockage internally of the expansion tank. The reason why I think that is because coolant has no problem coming out of the bleeder screw, but it will NOT stream into the tank from that small hole.

I have tried half a dozen times over the course of two days and I just cannot get it to stream out. Ive tried just about everything that was suggested.

Ciff

50 posts

165 months

Tuesday 14th June 2016
quotequote all
If it doesn't stream with some revs on (needs to be over 2k bleed screw in cap off) you either have a dud water pump or a blockage somewhere. Does the heater work.

Edited by Ciff on Tuesday 14th June 06:30


Edited by Ciff on Tuesday 14th June 06:32

wirewick

Original Poster:

8 posts

140 months

Tuesday 14th June 2016
quotequote all
Heater works. Waterpump is brand new, was changed along with all the other cooling system parts. Thanks for confirming my suspicions. It must be a clog in the diptube of the expansion tank. Its a brand new one, so I will see if the vendor can replace it for me.

Triumph Man

9,654 posts

199 months

Tuesday 14th June 2016
quotequote all
I know, op, that you say you may have a blockage so this relates to other comments regarding raising the car. If the m52 is Anything like the m50, the easiest way to bleed it is to undo the top hose from the radiator, loosen at the thermostat end, and rotate the hose. Fill via this, it will bubble as air bleeds from the system, and fill until you cannot get anymore coolant in. Do it back up, fire her up, heater hot, fast idle, and it will be done. Then slacken the bleed screw on the rad to let out any little bits of air left.

kev b

2,756 posts

197 months

Tuesday 14th June 2016
quotequote all
I recently borrowed a vacuum pressure bleeder/filler and used it on a number of cars including an MGF, what a revelation, simple and quick, automatically filling to the correct level, no guesswork or spilling coolant with a funnel.

One of the most impressive pieces of kit I have ever used and a bargain at £60ish, I cannot recommend it highly enough, especially for hard to bleed cars.

wirewick

Original Poster:

8 posts

140 months

Tuesday 14th June 2016
quotequote all
Triumph Man that sounds like a pretty good technique. That way you dont have to wait for the car to get warm and the thermostat to open for the radiator to fill. Kind of a head start on a tedious process.

eztiger328

198 posts

141 months

Tuesday 5th July 2016
quotequote all
Ciff said:
Run it at 2.5k rpm and you will see coolant moving into expansion tank

When I bleed mine I raise front of car fill with bleed screw out give it 30 minutes to settle. Refit bleed screw and radiator cap then run it with heater on full at 2.5k for a minute and its all done. Top up if needed
This ^

Also good idea having a mate give the top and bottom hoses a good grope while your keeping the revs up.

P.S you dont need to remove the bleed screw completely.